Out of Stock
Sign up to get notified when it's available to order.
First of all, why subject your Raspberry Pi to this level of stress? In the case of Raspberry Pi 4, the A72 CPU is so powerful that it can overheat if it doesn't have enough cooling. This results with the CPU being governed (slowed do...
Now that we've investigated and explained how How GPS Receivers work we can apply that understanding to some real-world applications of of the ideas. To start, we can use any GPS receiver, an Arduino Uno and some male-to-female Jumper ...
In August of 2014 Shanghai-based chip manufacturer, Espressif, released a ultra-cheap Serial to Wi-Fi chip called the ESP-01. At the heart of the ESP01 was an ESP8266 chip broken out into the 8 pins needed to program it via a microcontrolle...
In this guide we'll create a simple HTTP server using a Raspberry Pi Pico W. This server will be accessible from within a local WiFi network and can be used to read sensors and control hardware - in our case we'll drive an LED and read the...
It would be good to have some understanding of Pycom microcontroller boards before reading this article. We won’t go into what capabilities each microcontroller board has. If you’d like an introduction, try our Pycom WiPy Overvi...
The Micro:bit by BBC is a great data collection tool, it just needs a little help remembering what it has measured! This tutorial is made for those Micro:bit projects where transmitting your sensor data over radio or Bluetooth to a computer...
There are a ton of electrical wire connectors, too many to elaborate on in a single guide, however there are a couple of connectors that as a maker you will come across. Often when starting your way into the electronics world all you need ...
A digital multimeter (DMM) is one of the most common tools on a Maker's bench. We use DMMs to take electrical measurements in a fast and relatively accurate way. The reason we call it a multimeter is because they can take multiple types mea...
In this article we'll show you how to connect your PiicoDev® modules to your favourite development platforms. Connection Guides Other Connection Methods Pinouts Connecting Many Modules PiicoDev Smart Modules Custom I2C Addres...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. One of the simplest sensors in an...
Back at it again with tips for IoT devices when connecting with Mobile networks. Quickly to explain The Internet of things (IoT) describes the network of physical objects (things) that are blessed with sensors, software, and other technolog...
The Micro:bit is a feature-packed development board that’s perfect for the classroom or the beginner programmer. Each Micro:bit has a built-in radio that can transmit and receive signals sent from other Micro:bits. The radio has a ran...
warning: Pycom has updated their libraries and the code listed below may not work. If you discover this and find a fix, please post it on our forum and we'll send you a $25 store credit along with a huge thank you. Go to Forum Thread. ...
Hello and welcome to our tutorial on using rotary encoders. Today we’re going to be taking a look at what is a rotary encoder, how does it work, why we would use it over other sensory inputs and creating code to use them. Rotary encod...
GPS is accurate and handy to use, so much so that we rely on it more and more every day. It's not often we take the time to learn how it works. The idea of GPS refers to a Global Positioning System; a collection of satellites in orbit above...
IntroductionWelcome to the guide for the Makerverse Essentials Kit. This kit provides the fundamental hardware required to construct many of the kits in the Makerverse Kits range along with providing hardware which will continue to be usef...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. Any good LoRaWAN device can send ...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. One of the most common sensors in...
Logic analysers are an incredibly valuable piece of test and measuring equipment, but sometimes it can be hard to work out exactly what you need, and what model is going to best suit your needs. If you’re not sure what a logic analyse...
Layer Exposure Time is the crucial parameter that when dialed in will change average 3D resin printed components into awesome, crispy, final results that capture every single detail of the CAD model. As a general rule for Normal Layer ...
The Internet of Things (IoT) describes the network of physical objects that are all around us which are blessed with sensors, software, and other technology for the purpose of connecting and exchanging data with other devices and systems al...
Feel restricted by your connectivity? Want to send data from a remote node 10km away from civilization? Or ~3km when you are in a built-up civilization. Feel the urge for Liberation? Then I have the solution for you! Using only hardware bu...
Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what you can do with it if you take a look under the hood. One of the most popular experiments to do with your Raspber...
You’ve been working on that project for days, even weeks, and you’ve gone through all the steps of the process; meticulously ensuring everything is above board. And yet, for some unexplainable reason, your circuit is acting out....
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. Sending data to the cloud is grea...
Hello there, how’s your day been? Good? Fantastic! Not so good? Don’t worry it’s about to get a lot better, because today we’re going to take a look at how to use the I2C interface on our Raspberry Pi to control I2C ...
So you’ve got your Raspberry Pi. You’ve gotten NOOBS setup on it, explored Raspbian a bit, and you’re feeling like a bit of a pro. Awesome! Now let’s get down to the nitty gritty side of things, what it’s ...
The full example-code is reproduced at the bottom of this article. Performing manual measurements (in bulk) is for suckers and undergraduate students. Thankfully, most lab gear comes with a digital interface like USB or Serial and you can ...
Electronics is fun, so far we have covered off on communicating between devices, making LEDs flash and LCD screen operation. However using electricity to control some form of movement in your project is a fun and interesting aspect to inves...
So we have vertical graphing of voltage and horizontal sweep, but our signal is just going to go bananas on our screen if we don't sweep at the same point in the waveform. That's where triggers come in, allowing us multiple ways to fix ou...
In this tutorial we will learn how to set up the Onion Omega2/Omega2+ for the first time. You will require the following: Onion Omega2 or Omega2+ An Onion Omega2 Dock, such as: An Onion Omega2 dock, eg. Power Dock or Bre...
In this tutorial, we will learn how to set up the Onion Omega2/Omega2+ for the first time using the command line. While the Omega2/2+ has a graphical setup wizard and a web-based GUI called the "Console," we have found both to ...
Ever thought it would be cool if your Raspberry Pi could see the world like you do? You’re in luck, camera support is an integral part of the Raspberry Pi hardware, it comes with a built in CSI connector for connecting camera ...
Introduction The Makerverse Motor Driver has been updated to a v20 design which now features a 5V output pin instead of the VM pin. Some images and in-video descriptions in this guide may be outdated This guide covers the use of the Maker...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. In the lasts article we looked at...
Raspberry Pi right? It’s amazing! Raspberry Pi has taken the world by storm and changed the way that people think about computing. The Raspberry Pi 3 builds on this with some amazing new features, however one feature that is still ab...
If you’ve ever come across the term ‘logic analyser’ and not been sure exactly what is was, you’re in the right place. Logic analysers are one of the less common pieces of test and measuring equipment, but they&rsquo...
Say you want to build a sun-tracking solar panel. You could add a tiny computer, like an Arduino, to control it. That might be all you need. But what if you need to connect to it to control it from somewhere else? Connecting it into your ho...
What fun would a computer be without a screen to see what you’re doing? Well if you own a Raspberry Pi and are curious about the different ways you can connect an external display or monitor up to it, then look no further. Today we&rs...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. Since you’ve got your new P...
This guide will teach you how to control any small and big servos with a Raspberry Pi 4 Model B (worth noting any Raspberry Pi Board with GPIO pins can be able to be used in this scenario. Servos are an immensely useful way to turn ele...
Thanks to huge advancements in technology over the last decade, the maker community that we know and love has thrived. It’s now easier than ever before to get started with programming and tinkering due to the innovation from brands su...
Speed or Perfection? That choice is what an understanding of Layer Heights whenever Resin 3D printing is going to provide you. Any Traditional Resin 3D Printer worth its salt will let you print with Layer Heights between 10 Micron to 100 Mi...
Raspberry Pi Compute Modules have developed in tandem with the many generations of Raspberry Pi single-board computers. These boards are in every right a microprocessor just like their bigger cousins however they are a very different form f...
Filament grinding is very unlikely to occur if your running an Ultimaker S5 3D Printer with Ultimaker materials or 3rd party supported materials. Filament grinding occurs when the knurled feeder gear slips against the filament instead of sm...
So in case you haven’t heard yet, digital LEDs are the go-to solution for any project that uses RGB LEDs and you want to avoid the rat's nest that ensures when using multiple RGB LEDs, each colour requiring its own connection. Digital...
Adafruit has done it again with the new and improved Circuit Playground Express. This new version of the Circuit Playground is packed with even more sensors, and capacitive touch ready connection pads. This is a great board for makers ...
Welcome to the C Programming Workshop for Makers! Here you'll be able to follow along with our series of easily digestible videos that cover everything you'll need to know to on your way with C programming and start making awesome projects....
Ever had the issue where you have dozens of old phone chargers and appliance plug packs piled up in a rats nest of AC-to-DC mayhem? We tend to breeze right past these square, black power supplies, not knowing what's happening under the hood...
We're going to pick up where the LiPo Battery tutorial left off and look closer at the Adafruit Powerboost modules for charging your LiPos. We talked about the rules of using these batteries and how to make sure you don't set your project a...
This guide is all about mounting PiicoDev® Modules. It covers how to mount modules to PiicoDev Platforms (or any other material up to 3mm thick), and shows the common dimensions and mounting-hole patterns for PiicoDev hardware...
Welcome to our beginners tutorial on analog electronics. Living in the digital age that we do, it’s easy to disregard the world of discrete analog components, however these concepts form the basis for everything from your mobile phon...
Introduction This guide will cover the basic functionality of the GlowBit Python library when driving a GlowBit Matrix 8x8 module. To follow along, it's best to have: A GlowBit Matrix 8x8 A Raspberry Pi Pico ...
Hello makers, if you love to prototype circuits and create electronic designs, then you’ll be familiar with the humble solderless breadboard. It’s where most electronic projects begin and is a familiar sight for tinkerers and in...
PiicoDev is the open-source and best-documented platform specifically designed with rapid prototyping and maker education in mind. As fellow community educators, we have infused PiicoDev with ideas to ensure that every home project, school...
So we’ve taken a look at what Bluetooth is in our Introduction to Bluetooth tutorial, and hopefully, you’ve found our Choosing a Bluetooth Module For Your Project tutorial useful in deciding which Bluetooth module is right ...
Cameras in combination with artificial intelligence create arguably the most powerful sensor you can ever put on a microcontroller. So that’s exactly what we will do here with an ESP32-CAM Development Board that sports an inbuilt 2MB...
Introduction This guide will cover the basic functionality of the GlowBit Python library when driving a GlowBit Stick 1x8 module. To follow along, it's best to have: A GlowBit Stick 1x8 A Raspberry Pi Pico or...
Welcome to Counting with Computer 101. Have you ever looked at a colour on a computer and seen something like this #28FE9A? Or perhaps the T-shirt stating ‘There are 10 types of people in this world, those who understand binary, and t...
SPI stands for Serial Peripheral Interface and it is a way to send data between microcontrollers and other small devices. It is a synchronous data bus, meaning it uses a clock to regulate the data transfer. SPI is also Full-Duplex com...
If you could operate your switch without physically toggling it on and off, you would open yourself up to an entire section of electronics. Relays are one of the best ways of doing this. A relay is essentially just a switch, controlled by a...
If you’ve ever built a robot with wheels, or any motorised parts really, you’ll have come across the issue of needing to drive it from your microcontroller. Because a standard chip is only able to output a small amount of curren...
What good is a robot if it can’t interact with the environment around it? Sensors are the backbone of almost every electronics project as they allow your program to make decisions based on external stimuli. We’ve got sensors for...
Today we're pulling out the breadboard, getting up and running with an RTC module then finishing up by making ourselves a clock that will keep the correct time even when we pull the plug. To achieve this we will be combining three main com...
Have you ever used an Arduino board, and wanted to hook it straight up to a JST connected LiPo battery but knew it wouldn’t work? Or maybe you wanted a microcontroller with built-in wireless capabilities? Well, Adafruit has developed...
What do we mean when we talk about the "Internet of Things"? Mostly we're talking about tiny computers that have access to the internet and do some useful work. Unlike the computers we're used to holding in our hands, they don't have a touc...
The Raspberry Pi 5 is here! Our favourite credit card-sized computer has just gotten an update and we already have one here to take a look at, so let’s power it up, run some tests, and see what’s new! (If you want to s...
I²C stands for the inter-integrated circuit and refers to a communication protocol we are going to use to communicate between our Arduino devices. In the past we have investigated the SPI and Asynchronous Serial Communications protocol...
Well hello there, if you’ve been looking at the amazing line-up of Saleae gear and wondered how to get started with it all, then you’ve come to the right place. Today we’re going to take a look at getting your Saleae setup...
It has finally happened, they figured it out! The new frontier of Colour Electronic Paper is here and I'm very impressed. People have been demanding this ever since the first E-Paper readers hit the market in the noughties. That black and ...
The aptly named Ultimate Kit 2.0 is the final kit in the line-up of educational robots from Makeblock. With over 160 independent mechanical parts and modules, the Ultimate Kit 2.0 answers the call for almost limitless creative freedom. Matc...
In this tutorial, we'll get some WS2812B LEDs (also known as GlowBits and NeoPixels) working with a Raspberry Pi Pico. If you haven't already set up Thonny for programming your Pico, follow our guide on that first. To follow along you'll...
If there’s an odd one in the Pycom family of microprocessor boards it’s this one, the SiPy. There’s nothing wrong with it, it’s just that its sister board the LoPy4 has the same capabilities as SiPy, plus a LoRa ...
Stepper Motors are a bit of a halfway mark between DC Motors and Servo motors, but they find a sweet spot that allows them to be perfect for certain applications. There are still a few main differences to be aware of when it comes to workin...
Sometimes all a good Pycom project needs is some colourful lights! This tutorial demonstrates how to control WS2812 LEDs with the Pycom Wipy and Lopy4. WS2812 or WS2812B LEDs (otherwise known as NeoPixels) are the most commonly used RG...
Arduino Projects with Motion (Using Sparkfun RedBoard) Welcome to the Third Project Set from the Sparkfun Inventors Kit V4.0 Guide! In this tutorial, we will explore the operation of a Servo Motor and an UltraSonic Sensor in combination wi...
We have a more recent guide to Stress testing your Raspberry Pi, this guide has been kept here for reference. Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what yo...
"Yes, I would recommend this a friend." That's the verdict of 90% of people who pick up the Rule your Room Kit from littleBits. We love it so much, we're most definitely recommending it to you and your family. But you don't need to take ...
A popular question that we get all the time is ‘How do I choose a speaker or amplifier to go with my project?’. It’s a good question, and if you’re not familiar with the terminology, it can seem a bit daunting to kno...
The Raspberry Pi 3 Model B+ (I’ll be calling it the Pi 3+ for short) is an update to the existing Raspberry Pi 3 Model B and was released on Wednesday 14th March 2018. It has some very interesting changes: The Broadcom BCM2837 has ...
Similar to how bats echo-locate and how submarines use sonar, the PiicoDev® Ultrasonic Rangefinder uses sound waves to measure the distance to an object. It sends out a high-pitched sound wave, which bounces off of the object and comes...
Toolheads for your 3D printer come in all shapes and sizes. The different models available from Lulzbot are all designed with a specific purpose in mind, usually to add a filament type to your 3D printing repertoire. Dual extruders enable y...
Electroluminescent wire, often referred to as EL wire, is a thin copper wire coated in phosphor which will produce light when alternating current is applied to it. The light emits a similar feel as if it were a neon light or ...
Hello, and welcome to our tutorial where we’ll be looking at two different types of soldering irons and which one is going to be best for your workshop. We’ll be specifically looking at soldering irons, not how to solder, so for...
Welcome to the benchmarking arena! We are going to put eleven microcontrollers to the test and see how they hold up against a set of fiendish tasks that we devised to push them beyond their limits. We chose most of our candidates based on t...
Ever wanted a pocket computer with a Full HD screen (1080x1920)? Love tiny GPIO screens like this 3.5 Inch from Waveshare but want one that is a little bigger and higher resolution so that it is easier to read? Or want a really premi...
Whenever you want to print larger than your 3D printer build space you are going to find yourself wanting to combine 3D printed parts together. Furthermore, as you wrap your head around 3D printing, you learn to save on filament by printing...
The Internet of Things(IoT) and its devices have been utilised by ‘DIYers’ and ‘Makers’ to connect projects to the internet and take advantage of the worldwide network we have created. Some might say a sentence with ...
In this article I'll compare three popular Arbitrary function generators. They are all about the same price point and popular among makers. The models up for review are: Rigol DG1022 (data) ...
The Raspberry Pi 5 is here and one of the biggest questions is, how does it stack up against the previous Pi 4? Well, we already have one to take a look at so let’s run some benchmarks and compare the two.(We also have another articl...
On the lower left-hand portion of every Adafruit Circuit Playground Express, there is a small onboard speaker and class D amplifier. This allows you to make some pretty loud sounds! The amplifier is also connected to the true analog output ...
The ability to connect your test equipment to a local PC is invaluable. It allows monitoring and the use of your equipment via a PC interface. That includes coveted mouse/keyboard control! This control centre capability is essential when yo...
Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what you can do with it if you take a look under the hood. One of the most popular experiments to do with your Raspberry Pi is o...
IntroductionWelcome to the guide for the Makerverse Audio Kit. This kit will allow you to build a music player, a musical keyboard, and a sound effect soundboard! To follow along you will need: The Makerverse Audio Kit The Makerverse ...
Introduction This guide covers the configuration steps required to use the Makerverse Supercap Real Time Clock module as a backup RTC on a Raspberry Pi. This is required for remote applications when Internet access is impractical and accur...
There is a new Raspberry Pi! The long-awaited upgrade to the Rasberry Pi 1 Model A+ (Rpi1 A+). In this article, we are going to look at how much improvement the new Raspberry Pi 3 Model A+ (Rpi3 A+) is over the Rpi1 A+ as well as how ...
We had a lot of fun making this speed build video for the Paris Flyer CarouSol Kit by Solarbotics. If you aren't already familiar, Solarbotics makes a great line of DIY electronics kits made from laser cut materials. They range from quite s...
The Raspberry Pi is an amazing piece of technology, and it’s the platform of choice for all kinds of projects. Something that makes it great is the integration of complex hardware that is taken care of for you. For example, if you wan...
Print-in-Place mechanism is one of the special things about additive manufacturing that all other manufacturing methods just cannot replicate. They use various hinges, linkages and joints to create moving parts that are printed as a single ...
The Raspberry Pi 5 was announced just a few weeks ago and across the internet, we have seen some recurring questions, so in this article, we tried our best to answer some of them. Contents: Overclocking Questions Cooling Quest...
Wouldn't it be great to have a single image, that encapsulated a tonne of handy 3D printing tips and information to hang on the wall behind your 3D Printer? Well, we agree so much so that we've gone ahead and created this infographic/cheat ...
Serial communication is the process of communicating between electronic devices one bit at a time. Serial means one after the other, so we think of serial communications as transferring data one bit at a time, one bit after the other. ...
Let's take a look at the new Siglent SDG1032X Arbitrary function generator. We're looking at yet another example of the closing gap between hobbyist and pro gear - the growing feature set and capabilities of entry-level equipment continues ...
If you’re a musician or have had anything to do with the entertainment industry, you may have heard of the term MIDI before. MIDI stands for Musical Instrument Digital Interface and was created in the mid-80’s as a way to standa...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. In our two previous Pycom article...
Let's unlock Biometric Control on our Raspberry Pi Single Board Computers! Biometric Technology uses unique physical or behavioral attributes that are individual to each person and not (easily) replicable. Extraordinarily everyone on Earth...
Introduction This guide covers how to connect the Makerverse Micro SD Card Adapter to a Raspberry Pi Pico and program a basic data logging script in MicroPython. To follow along, it's best to have: A Makerverse Micr...
The latest Circuit Playground board, the Adafruit Circuit Playground Express comes equipped with an onboard IR transmitter and receiver! This can be used to communicate with TVs and other household devices. You can also use infrared remote ...
This guide will help you get started with a PiicoDev 3-Axis Accelerometer. We'll walk through some examples to read acceleration, infer tilt angle (from gravity), and detect tapping and shaking. An accelerometer is a device that mea...
Arduino Projects with an LCD (Using Sparkfun RedBoard) Welcome to Project Set 4 in the Sparkfun Inventors Kit Guide! In this tutorial, we will look into using Liquid Crystal Displays (LCD's) to print data. This ability allows us to remotel...
It is long overdue. Time for a table with all the info comparing every generation and style of Raspberry Pi from the genesis to now! We have come a long way to have our hands on the Raspberry Pi 4 Model B 8 GB so it is time we give you the ...
We’re in a golden age of connectivity, the internet we know today has given us the tools to connect anything to anything, and now with the platform brought to us by Particle, DIYers everywhere can connect the creations up to this va...
Hey all! By now you should have heard about all the wonderful Teensy Boards produced by Paul Stoffregen and the PJRC team but, in case you haven't, they're a collection of high-speed, ARM-based microcontrollers that...
This will be a quick article showing the process to flash the legacy Raspberry Pi OS 'Buster' Debian 10 (or any previous OS iteration) to a Micro-SD card. With any exciting new Operating System (OS) release, there are always small ...
If you hang around 3D printers, X-Y plotters, CNC machines, drawing machines, or people who use any of them G-code is a term that will universally come up no matter where you find yourself in the world. But what is it? And how is it being u...
Once you setup your printer and finish printing your first rocktopus, you will inevitably want to move onto more ambitious prints right away. It’s understandable, all the possibilities all at once, I get it. We are going to step you ...
Where do I start? If you’re new to programming Python is a great place to start! I’ve seen Python taught to primary school age children and I have used Python in a Machine Intelligence course at university. It’s no wonder...
Hey guys, how much fun are microcontrollers? They’re your own miniature slave to do your bidding in whatever way you choose, however as fun and all as using them to do math and crunching numbers, the real joy is seeing them interact w...
Welcome to the Arduino Workshop, where you'll be able to follow our guided course which covers everything you'll need to know in order to create your own Arduino projects and become a leveled up maker. My name is Sam and along with being ...
This will be an overview, initial setup and first print guide for the Ultimaker 2 and Ultimaker 2 Extended . Quick links for the contents of this guide is seen below. Printer Overview Printer Characteristics ...
So, you want to control things with your Particle Photon and/or Electron do you? Well, a relay is a perfect way to do that. Whilst there are many ways to control an electrical signal from digital logic such as transistors and optoisolators,...
In this guide, we'll learn what a Rotary Encoder is, when and why we might use a Rotary Encoder, and how to use a Rotary Encoder with a Raspberry Pi Pico. To follow along all you'll need is: A Rotary Encoder - we recommend using our br...
The Makey Makey introduces the concept of using everday objects like fruit, lead pencil drawings, play dough etc. to interact with your computer via USB. The Makey Makey acts like a HID device over USB, which means that it behaves just like...
After lovingly crafting your project on a Raspberry Pi, you might want to share it with the world. The easiest way is of course just to publish a list of the commands that you executed to get everything up and running. For complex proj...
Let's do some creative projects to get familiar with the GlowBit™ rainbow and micro:bit. The animation runs for 10 seconds, and can be started by pressing either of the micro:bit's buttons In this guide we will: Wi...
To fully equip ourselves on our Python odyssey we will take a leap into Operators and their Precedence. Python is undoubtedly a Homeric programming language, epic in its possible applications and vast in its potentials. Operators ...
The Raspberry Pi 4 Model B is finally here! This is a huge leap forward for single-board computing and what better way to explore it than power one up, run some tests and stress it out! Here are the test results for those peopl...
[Update 18-02-2021 - Made a Vesa Mount for the Argon One M.2 Case as well so nobody missed out] A quicky article for those who have their Raspberry Pi 4 Model B all tucked in snug by the very stylish Argon One Case but wish they could...
The Infinity Mirror Kit V2 is a desktop display that creates a dazzling optical illusion - a tunnel of light that tears through space! The Infinity Mirror Kit V2 entered production in October 2018, and now ships with an Adaf...
Let's turn it up to 11! Today we are getting right into Bluetooth Audio Receivers in particular the MH-M38. The MH-M38 is a stereo audio receiver with loudspeaker outputs (and an inbuilt amplifier) that can play music from a smartphone/com...
We've been familiar with the Mooshimeter for a while now, we've got tutorials on Getting up and running with a Mooshimeter, how to datalog with your mooshimeter, taking voltage/current measurements with multi-meters and finally a whole arti...
Welcome to the 3D Printing Workshop! I'm Aidan from Core Electronics and in this workshop we are going to take a hands-on journey into the exciting technology that is 3D printing. I have personally spent the past 12 months immersing mysel...
What a time to be alive! It’s never been easier to get into electronics and programming with platforms like Arduino, Raspberry Pi, Chibitronics and many more. These platforms are great, but with the Internet of Things (IoT) becoming m...
Let's get set up with scripting in Thonny for the Micro:bit. We'll install Thonny, configure for Micro:bit, and write our first script. All you'll need to follow along is a Micro:bit v2 GO kit Contents Install Thonny Set u...
Pulling the power to your Raspberry Pi can cause image corruptions & other issues that can damage your Pi! In this article, we will create a small push button that will work as a ‘Safe-Shutdown’ option. We’ll connect i...
A big project request for the Raspberry Pi is the ability to make a digital sign, that loops images/videos/other media fullscreen with no interactivity. This can be a great way to display dashboards, promotional videos and other media. For ...
The New Version of the Raspberry Pi 4 has started going out to makers everywhere. If you are wanting to upgrade your old RPi3 project to take advantage of all the cool new features there are a few steps we are going to have to take first to...
What We'll AchieveThis guide will help you set up a Plant_io controller to automatically irrigate a plant of your choice. This example focuses on germinating seeds, but this is only one option. Along the way we'll: Assemble a hardware pl...
In this tutorial, we will learn how to code for the Onion Omega2 on our PC, and then wirelessly upload our code using the ATOM text editor. The ATOM text editor is a powerful and easy to use text editor developed by the team at Github...
The Micro:bit has the ability to measure temperature by sensing the temperature of the silicon die inside the main CPU. This works because the Micro:bit runs cold, and the temperature of the CPU is usually a good approximation of ...
IntroductionThis article will compare the Raspberry Pi Pico, and Pico W. Aside from the obvious difference (the Pico W has wireless connectivity), there are a few smaller and more subtle differences that are worth considering.Physical Comp...
One of the greatest features of the Adafruit Circuit Playground Express is its MakeCode compatibility. MakeCode is an exciting coding interface that makes coding accessible for those with little or no exposure to how coding works or how it ...
Welcome to the Circuit Playground Express Workshop! This workshop is geared toward educators and coding beginners, who want to get started programming with this easy to use platform. We will go over everything you need to know to get you st...
Introduction This guide will cover the basic functionality of the GlowBit Python library when driving a GlowBit Matrix 4x4 module. To follow along, it's best to have: A GlowBit Matrix 4x4 A Raspberry Pi Pico ...
The multimeter is one of the essential tools in your electronics toolkit. These battery operated devices combine several measurement functions into one easy to use device. You can get Analog or Digital multimeters, each displaying your meas...
This tutorial is aimed at getting some instant gratification from your WS2812 LEDs (also known as NeoPixels). I'll briefly cover a bare-bones setup for Arduino. If you've never used an Arduino before, we've got you covered with our free, o...
A common issue many makers face when they move from microcontrollers to Single-Board-Computers is how to get them to run a program automatically when they are powered on. People who have cut their teeth on Arduino, Micro:bit, and other micr...
So you've got your Raspberry Pi 3 Model A and need a case to house it in. In this short guide we're going to step through the considerations you should take when designing your own case, as well as provide you with all the files you need t...
Have you ever lost or broken a TV remote before it's time? Have you ever wanted to spice up the way you change channels or inputs on your TV? Have you got a greedy housemate who always steals the remote off you? If any of these are the case...
If you ever needed a performance boost when running Machine Learnt AI Systems (like facial recognition) with a Raspberry Pi Single Board Computer then I have a solution for you. The OAK-D Lite. The Oak-D Lite is the Leatherman Multi-tool o...
Force-sensitive resistors (FSR) are remarkable electrical components and are proper unsung heroes in the Makers World. Name me a better variable touch input device which has basically no moving parts, all whilst being available in such a t...
If you're looking for a benchtop power supply, but you're unsure of what you should be looking for in a decent supply for your workspace, we have got you covered with this guide. We will look at the specifications to look out for in a power...
Life’s better in colour right? Then why are you still using boring old regular LEDs in your project, when you could be using addressable RGB LEDs. Now LEDS that have Red, Green, and Blue integrated in a single package are nothing new,...
Dual Extruding with FDM 3D Printers is typically reserved for the most expert-level makers. By adding the ability to print with 2 materials, you open yourself up to a spread of conditions that simply didn't exist with a single extruder setu...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS ...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto y...
IntroductionIn this guide, we'll get a Raspberry Pi Pico W to send and receive data to the cloud using the MQTT protocol. To follow along, all you'll need is: A Raspberry Pi Pico W Understand how to connect the Pico W to WiFi Underst...
Have you ever heard people talk about how amazing the Internet of Things is and how you can leverage the power of the internet by creating IoT devices, but not really known how to get started? This tutorial is for you! We’re going to ...
This Tutorial is all about the MicroPython Programming Language. We will discuss what MicroPython is, why you will want to use it in your projects and we will share some resources to help you learn further! What is MicroPython? MicroPyt...
Is it hot in here, or is it just my Raspberry Pi? A Raspberry Pi sitting on a desk doing nothing is kind of boring. However, a Raspberry Pi that can measure the temperature and make decisions based off that information is awesome! The Rasp...
In this tutorial we’ll be getting familiar with basic use of the Raspberry Pi terminal. We’ll cover navigating the file-system, making directories, writing and editing text files, and just touch on the use of wildcards. To get ...
The Raspberry Pi as we know it today is just the “tip of the iceberg”, the product of more than a decade of development, spanning 4 generations with up-to 18 boards and counting released so far. Alongside this development, there...
Both Python and MicroPython are powerhouse programming languages. Each of them is capable of supporting your programming needs to almost the limits of your imagination. Both languages are transportable, open-source, growing in popularity, c...
This guide will be a rundown on Python, the open-source programming language built by the hugely intelligent Guido van Rossum. This guide will also contain external links to Python resources and download links. Programming is...
To better yourself for future programming skylarking let me welcome you to the next step of understanding Python. Loops are among the most basic yet also the most powerful features in programming. Utilised by all modern programming language...
Cura is constantly being improved upon and half the fun is keeping on top of all the new changes and new offerings it gives. For completely free software, they are doing an amazing job. Nailing the recipe for a 3D prints will let you get th...
Co-Polyester is an astounding material in terms of properties, all the best properties of Tough PLA and ABS which are then dialled up just that extra bit in regards to both ruggedness and durability. Ultimaker offers two versions of Co-Poly...
Geophones are devices that generate electric signals proportional to the particle velocity in a sound/compression wave. More simply a Geophone is a super low frequency microphone for the ground. Geophones are used around the world to measu...
The Micro:bit is great for small portable projects like a soil moisture sensor. In this tutorial, we will walk through how to program a Micro:bit to make a reliable and consistent soil moisture sensor that will give consistent readings. The...
Want to setup a wireless XBee network between some Arduinos and your PC? We're going to show you how. We will be using Series 1 XBee modules alongside some XBee Explorer USB modules from Sparkfun to set up our own Personal Area Network (PAN...
Let's get started with the PiicoDev® OLED Module SSD1306. In this guide, we'll connect the PiicoDev OLED to our Raspberry Pi Pico and get it working with some example code to display text, shapes, and animations. To f...
The Infinity Mirror Kit is a desk-top display that creates a dazzling optical illusion - a tunnel of light that tears through space! Note: This tutorial is for the Infinity Kit V1. We updated have updated to the Infinity Kit V2 as of ...
Ultimaker Cura is an excellent slicing software to get the best out of your 3D printers and make the greatest models it possibly can, but it can do so much more! Cura is a brilliant means to inspire and expand your own creativity particular...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Mi...
Let's get started with the PiicoDev® OLED Module SSD1306. In this guide, we'll connect the PiicoDev OLED to our Raspberry Pi Pico and get it working with some example code to display text, shapes, and animations. To ...
Let's get started with the PiicoDev® OLED Module SSD1306. In this guide, we'll connect the PiicoDev OLED to our Raspberry Pi and get it working with some example code to display text, shapes, and animations. To follo...
In the Plant_io Basic Setup Guide we assembled the Plant_io platform to automatically irrigate plants, and sprouted some seeds. As the project runs, a log file is updated with data captured at each interval. This simple log allows us ...
Today will be all about controlling Fully Addressable LED Lights using any Espressif ESP32 Development Board and your mobile Phone all through WIFI! All possible by WLED. There are many ways to use your mobile phone to remotely...
This guide will help you get started with a PiicoDev Real Time Clock. We'll set and read the time/date, observe the power-backup capability, and configure the RTC with an alarm. A Real-Time Clock (RTC) is a timekeeping device that accurat...
This guide will teach you exactly how to use a Raspberry Pi Single Board Computer to independently control 4 relays. A Relay is an electrically operated switch. This is all possible thanks to the PiRelay V2 HAT from SB Components. These re...
Flawless high-quality audio output on a Raspberry Pi Single Board Computer! All is achieved by the IQaudio DAC+ HAT. This dedicated DAC lets you enjoy high-quality, distortion-free, artifact-free, low noise, and high-bitrate audio playback...
One of the most critical parts of a successful 3D print is the correct material choice and through its careful consideration you will get the best result for the final component you had in mind. Ultimaker has a wide range of 3D printi...
This is an update to an older guide done so that we can provide you with the fastest, most modern, and best way to set up your system. Nothing beats bright shiny colourful lights and this guide demonstrates the fastest and most customizab...
This guide will demonstrate exactly how to control any large DC Motors that we stock with a Raspberry Pi Single Board Computer, through code or through a Bluetooth Controller. To clarify (in my mind) a large DC Motors runs at 12+ Volt...
Welcome to the MicroPython for micro:bit workshop! This workshop is aimed at makers who want to start programming with MicroPython, we will be using the micro:bit as it is very easy to use so we can cover the important concepts that will ap...
Welcome to the Python Workshop, where you will learn everything you need to hit the ground running with the worlds most popular programming language Python. My name is Tim and am a passionate maker and cherish free exchange of knowledge. I ...
Welcome to the Raspberry Pi Pico Workshop, where you will learn everything you need to know to hit the ground running and start making your own projects with the Raspberry Pi Pico and MicroPython. This workshop is designed for complete beg...
I wanted to build a weather station. After some googling I found a great ‘how to’ guide using a raspberry pi.
I was also interested in learning Python, so I decided to dive right in...
I wanted to build a weather station. After some googling I found a great ‘how to’ guide using a raspberry pi.
I was also interested in learning Python, so I decided to dive right in...
This project uses a US100 ultrasonic distance sensor to detect instances of a garage tilt door being left open and sends an alert via the IFTTT mobile app. Additionally, the device logs temperature and pressure to a Thingspeak channel using...
I'm an amateur musician but a pretty serious classical & jazz pianist, and this project arose out of my interest in exploring the difference between writing music for synthesisers and music for piano. I work as a mathematician, so...
This project started due to the smoke haze that enveloped our area during the 2019 and 2020 bushfires. I wanted something to check the air quality of my home and maybe find areas where it needed better sealing. In addition, the BMP280 senso...
UV is important to reptiles (and people) in processing vitamin D3 which is needed to absorb calcium. Without it reptiles often suffer from Metabolic Bone Disease (MBD) which leads to weak bones and can be fatal. Thankfully, pet shops have t...
My brother-in-law has a dairy farm in Victoria and many hours per week are wasted traversing the farm to check water tank levels, opening/closing valves, and other small tasks that could easily be remotely monitored and controlled. It was ...
This project logs temperature and pressure observations to a ThingSpeak channel using an ESP8266 WiFi module.
For this project, I designed my circuit and ordered a PCB using easyEDA. The project gets power from a USB port and uses a...
For this project, I designed my circuit and ordered a PCB using easyEDA. The project gets power from a USB port and uses a...
Introduction This began as an idea after building a very basic single-channel unit. Commercial smart watering systems use a Wifi connection to the internet and get weather reports to determine the level of watering required. These systems...
This project uses a Raspberry Pi and TFT display panel to provide a desk clock that also monitors our Home Solar and Battery system, and the weather, in one neat unit.
We recently installed a Solar Panel system and a Tesla Powerwall...
We recently installed a Solar Panel system and a Tesla Powerwall...
The objective of this project was to create an Internet of Things (IoT) device that could give pet access to a food bowl when a text message command was sent from a remote location. I had never done an IoT project before, so I wanted to ke...
If you have chickens and find you're not always available to close the gate at night or check the water levels each day, then why not use an ESP8266 to automate your chicken door and receive alerts door status and low water level, as well a...
Being punctual is important. Hence accurate time is required. Clocks tend to miss out when it comes to accuracy especially when they are set by the user. So, why not get accurate time from the internet and use tried and tested hardware to ...
We've got a whole bunch of Raspberry Pi 3 Cases here at Core Electronics. From the Official Enclosure that's perfect for most uses, right through to the gilded PiBow Coupe from Pimoroni. All of the cases we see have one or two impressive fe...
I was wanting to know what the water temperature was without having to physically go and check and I was curious about how warm the water would get during a sunny day and how much heat was lost overnight. I am interested in the idea of home...
I used an Arduino and a US-100 ultrasonic sensor to make an extremely low-cost tide gauge. This project measures the tide by sensing the distance to water using a US-100 ultrasonic sensor. The device has a 3D printed base&nb...
Introduction Searching for solar panels and related items on the Core Electronics website; I came across the Solarbotics GraviTrack Marble Machine Kit. I thought the kit would be a good educational tool for the grandkids. The kit was a hit...
I was looking for something educational to 3D-Print for my child in Thingiverse and came across the concept of the Math Spinner. I found the models lacked a method of checking the answer so I wanted to automate it. The core design is inspir...
This project creates a functional 12-volt portable battery case for camping or other outdoor activities.The battery box provides a 12V cigarette lighter socket for running lights with an on/off switch for ease of use. There is also an Ander...
I am an amateur musician, coder, and electronics maker. When I found out that the Novation Launchpad (mine is a mini MK3) can be programmed, I was excited about creating unique music. The idea is to use the Launchpad to play a game and use ...
Chances are if you are anything like me, being a maker is often an excuse to create as big of a mess as possible during the duration of a project. And after the project is finished? You are left with an enormous mess to clean up, taking awa...
Making a dumb coffee grinder slightly less dumb. This is a programmable timer tethered to a Rancilio Rocky coffee grinder. The Rocky is a "dumb" grinder and electrically very simple. Basically it's an ac motor with an on/off switch and a m...
Despite having two high-quality variable (but analog) benchtop power supplies, I decided you can never have too many. I also specifically wanted a fixed, multi-output supply for standard project voltages such as 3.3V, 5V, 9V, 12V, ...
Despite having two high-quality variable (but analog) benchtop power supplies, I decided you can never have too many. I also specifically wanted a fixed, multi-output supply for standard project voltages such as 3.3V, 5V, 9V, 12V, ...
IntroductionI wanted to bring ageing, and failing, Home Automation infrastructure into the modern age whilst retaining hardware investments already made. Our house had Universal Power Bus (UPB) dimmers and switches installed at build time...
This mini cube is made up of six 4x4 WS2812B panels giving a total of 96 individually addressable RGB LEDs. Buried inside the cube is an ATTiny85 microcontroller powered by a 120mAh Lithium-Ion battery. It also contains a mercury switch and...
Our recycle bin is collected fortnightly, but I can never remember which week, and the printed calendar changes every year! So I made a Raspberry Pi Pico W and GlowBit Matrix powered model wheelie bin which shows when the bins are due at a...
Wow - this is one monstrous sounding and great looking speaker - even if I do say so myself! This is basically a 2.1 (stereo + subwoofer) system made with 3D plastic parts. Both the full range and subwoofer speakers are based on closed (se...
The concrete body of the lamp (which, to my eye look a bit like a leek) is made is two halves. The 1st and 2nd halves are cast in 2 steps using the same mould twice. I had a few failed attempts at making the mould entirely from sta...
The concrete body of the lamp (which, to my eye look a bit like a leek) is made is two halves. The 1st and 2nd halves are cast in 2 steps using the same mould twice. I had a few failed attempts at making the mould entirely from sta...
Who says you can't have it all? Good looks and a great sound! My name is 'Holman" and I'm a Bluetooth speaker in the form of mans best friend - a dog of course! Why is my name Holman? Well, that's the name of the manufacturer of the PVC pi...
I strapped a Raspberry Pi Pico W to my garage door motor and now I can control my garage door from my phone! The Pico W hosts a simple webpage on my local network with three control buttons - one for Up, Stop and Down. Pressing one of...
These days we can do just about anything on our phone, we can control so many aspects of our lives using the technology in our pocket, but the most mundane aspects of our lives; opening the garage door, blindly reaching for the light switch...
Introduction My passion hobby is night-time time-lapse photography and astrophotography/nightscapes. This means a lot of time spent outside in the dead of winter overnight and an issue that I faced was dew condensing on the lens. This is...
This project will measure atmospheric conditions (Temperature, Humidity, Air Pressure) and log them to an SD card over a long period (months!) while running off a few AA or AAA cells. Usually, projects powered by an Arduino Uno are quite p...
I use a Raspberry Pi running EmonCms for collecting sensor data and controlling devices around the home but several things have been on my To-Do list to enhance its functionality. A Shutdown/Power Down/Startup circuit. Proportional fan...
I’ve always been fascinated by LED screens and seeing beautiful colours mix and merge to create vibrant displays. I also love games, so what better way to combine the two than a giant LED pixel matrix which can play games, display aud...
I was down at a local game shop recently and noticed their range of chess boards and decided to try my hand at a simple little project. I'm a big fan of Doctor Who, Chess and 3D Printing. So I decided to combine them all together into a fun...
I like working with the Pi Zero W and Pi 4 as they are very compact, very powerful and very cheap for the capability they offer. I want to use them on small projects, stand-alone, and can't always guarantee power. As we know most Pi's don't...
My son really wanted one of the mini NES when they were released, however he missed out. I already knew that you could use a raspberry pi as an arcade emulator, so I thought why not build him one.
I grew up playing old arcade machi...
I grew up playing old arcade machi...
Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosure, I'm just about ready to turn on some serious 3D printing work. But before I dive into that endless pool of fun, it's a good time to take ...
I had been captivated by the sound levels of trains I could hear passing by Metford throughout the day/night. I wondered if a sound level sensor reporting data back over LoRa would help me understand when a train was noisy. I also like the ...
I made a Raspberry Pi camera that captures GIF files and optionally tweets them over WiFi! It's built around a Raspberry Pi Zero W and a Pi Camera module. The camera connects to a pre-programmed WiFi network to tweet the gifs, but...
This project started because I wanted to know the signal strength of the Wifi in various places around my house. I had set up a Pi Zero as a simple watering system controller. It would switch a solenoid on and off based on a 7 day schedule;...
Have you ever wanted to make a Weatherproof Weather and Air Quality System that transmits its edge-collected data long-range through LoRa (up to a 10Km range) and then have that data automatically uploaded to the Internet to be gorgeously ...
Do you get nightmares of losing your YouTube Subscribers? If you do, you are not the only one. Luckily I have made this "YouTube Desktop Notifier" to keep me up-to-date with my channels Subscriber and View Counts. This very simple DIY ...
This is the third project I've put up using the Makey Makey, and it's incredible fun, but it's also the simplest. Today I'm going to show you how to make a simple Skill Tester game complete with sound effects using a Makey Makey board and s...
This project has been a long and tricky one for me, I purchased my robot arm kit from Jaycar many years ago with the intention of controlling it from the start. I used to work with industrial robots, so when I saw this robot kit for sale I...
This project incorporates two Arduino boards, in a Master/Slave setup. The master is one with an accelerometer (ADLX345) and the slave has a Servo attached (SG90). When tilting the accelerometer, the master Arduino tells the Slave Arduino t...
This project started life as an alarm clock for my son made to look like the time circuit from the Back to the Future movies. The display can show the time in various formats, including the one from the movies of course. It's configurable v...
This is an awesome project that takes about 6 hours to complete. Hours upon hours of endless fun thereafter! Ideally, some prior soldering experience is advantageous but if you take your time and practice before you start it's beginner fri...
This project uses an Accelerometer to detect when you are leaning left or right. Depending on if/where you are leaning, it will flash LEDs on the right or left of the bike's rear. Powered by an Arduino and a 12v battery pack (my case 8 AA B...
This project is about how to build an 8 bit computer on breadboards, from 7400 series basic TTL. I am currently in the process of building mine, and will give an overview of what's involved. It is a great project that can teach you a lot ab...
I used to sleep in a caravan on my grandparent's property and as amenities were inside the house I had to go in and out of it quite regularly. I got sick of fumbling around with keys to go in and out of my caravan, so this project uses an A...
Today we will be making an Arduino circuit that will start playing a noise if the water (or surrounding environment) reaches a certain temperature, in our case, that temperature will be 100° Celsius. This is a useful little projec...
It is real and here it is! Including everything you need to make one a Luma 1 for yourself! So allow me to introduce you properly to the Luminator Mark 1. I'm talking all the ins and outs of this inside-out neo disco ball so you can ...
This piece combines recycled electronics extracted from decommissioned computers and new electronic components. I had an idea I wanted to incorporate a lighting element into a contemporary sculpture so it was just a matter of coming up with...
In the area I live, there are often kangaroos that jump in front of traffic, often from blind spots, and can get themselves into harm's way. I wanted to build a low-cost solution that can alert drivers to kangaroos in these blind spots to r...
Converting a Mule into an articulated 4 wheel vehicle. A 'Mule' is/was a hand trolley with a motorised elevatable platform. What for? Just for fun, want to be able to control it using the R2D2 droid inventor app via LittleBits boards, why ...
The aim of this project was to create a working model of the aircraft exterior lighting systems. Initially, this started as a simple project for Uni, but I wasn’t having that. I wanted to learn something. So of course, I went over the...
This was an attempt to build a autonomous robot that could follow a person or bike while carrying tools, equipment or water. This project used a Raspberry Pi3 and Wild Thumper All-Terrain Chassis.Here's a video of the build: There's a re...
This project is about adding a wireless Adafruit Feather HUZZAH ESP8266 or ESP32 v2 with Adafruit Featherwing 128x64 OLED to interface with the self-assembled MightyOhm Geiger Kit.
So, my wife wanted to have some small plants in the house. I didn’t, so we compromised, and got some plants. The only thing is that neither of us remembers to water them, so I wanted to build a sensor array to monitor the moisture con...
The aim of this project was to use the sun to charge some batteries with 1W and 2W Seeed solar panels. The DFRobot Solar LiPo Charger and a Sunflower Solar Power Manager were purchased. Initially, this was unsuccessful because I did no...
After seeing how much fun people had using the Makey Makey as a gaming controller for our RetroPie setup, I decided that more fun, simple projects that can be made using household materials were in order. So today I present to you the piano...
Do you love your Wii and its ability to play all GameCube games perfectly but wish you could take it on the go like a Gameboy?
Well, I definitely did and if you're like me so do you. And here is the right place...
Do you love your Wii and its ability to play all GameCube games perfectly but wish you could take it on the go like a Gameboy?
Well, I definitely did and if you're like me so do you. And here is the right place...
Introduction This project started because I needed to replace a water tap timer that had seen better days. The aim was to use a Raspberry Pi Pico and a couple of PiicoDev boards to do what the water timer did. The actual stopping a...
The driver behind this project is to allow the remote control of some of the equipment in my shed. I have a CNC router/laser cutter that uses my compressor and dust extractor whilst it is running, and well whats the point in having a comput...
This project is to modify a Dell multimedia keyboard into a Raspberry Pi Zero dedicated keyboard with external powered USB hub. You can find this article in my blog http://sizeofinfinity.blogspot.com.au/2017/06/modify-dell-multimedia-keyboa...
Turn Your Raspberry Pi into a Steam Link Sometimes Retropie just isn’t enough to get the best possible gaming experience with the Raspberry Pi. I originally purchased the Raspberry Pi 3B+ so that I could install Retropie and Kodi to ...
Since I was young, I've always loved to explore. Over the years, I've tinkered with RC cars and played with planes, which were always plenty of fun. But I always dreamed of going out further - out into the real world, far beyond the confine...
This project is to build a super cheap wireless adapter based on Raspberry Pi Zero and ENC28J60 ethernet module for Xbox 360I have two Xbox 360 consoles and today I want to connect them together but I only have one OEM wireless adapter. It ...
Do you want a quick, easy, cheap RF remote control for your Raspberry Pi projects? Well, look no further than the front door! As you've probably got a half-duplex RF setup you've never considered using in a project before. Try this simple h...
Summary A Raspberry Pi 3B is used to collect digital counts from an electronic rain gauge (1mm of rain per reed switch closure by magnetic see-saw). It has been running without issues for over 12 months. A UPS powers the Pi so it is immune...
Although there are commercially available lighting kits for Lego models, we found those that are available for this Hogwarts Castle can seem a little garish and don’t do the best job at concealing the wires. We felt that with t...
A smaller version of our amazing Infinity-Mirror Table - the Desktop Infinity Mirror compresses all the colourful goodness into a picture frame-sized display. The entire design is made from laser-cut acrylic that we cut in-house. Check out ...
Introducing to you today, the Quadbeest, the next evolutionary step in the Strandbeest genealogy. It seemed to be about time for Strandbeests to evolve to take over the air, so I made it happen. Able to be controlled over a kilometre in the...
I want to make a portable music box that my 2 year old kid can operate intuitively on her own. So, Spotify or any other on-demand music platform with tablets and Bluetooth speakers are out of the question. Remember the good old days of putt...
Here is a project I just could not help myself but build. A 3D printable Ukulele with a body as large as I could fit standing upright on the printers here. The intention was to make it as large as possible, using no supports, and without th...
The purpose of this project is to design a system that will automatically track stars or satellites. The first version, described here, is specifically to track stars and operate a Raspberry Pi HQ camera to take a series of long-exposure im...
I have a peer-reviewed study on my desk and it confidently tells me that all the capacitors on planet Earth want to be synthesisers when they grow up. To make the world a better place, let's realise the dream of four fortunate elec...
After experimenting with automatic blue light filters on my electronic devices I wanted to replicate the idea with the lighting around the house so that it would gradually transition to warmer colours as the night progresses. I believe this...
I like to take on projects that give me an opportunity to learn new things. For this project, my two goals were to learn more about face detection algorithms and PID controllers but of course, there were so many more skills learned along th...
Makers love reviews as much as you do, please follow this link to review the products you have purchased.