Search results for: 'Tsunami Super WAV Trigger'
- Tsunami Super WAV Trigger (Qwiic)SKU: WIG-18159 Brand: SparkfunBased on a new generation ARM Cortex M7, the Qwiic Tsunami extends polyphony to 32 mono or 18 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks...
- Tsunami Super WAV Trigger - 25 Voice (Qwiic)SKU: WIG-20636 Brand: SparkfunBased on a new generation ARM Cortex M7, the Qwiic Tsunami extends polyphony to 25 mono or 13 stereo simultaneous uncompressed 44.1kHz, 16-bit tracks...
- WAV TriggerSKU: WIG-13660 Brand: SparkfunThe WAV Trigger is a unique high-fidelity polyphonic audio player with surprising capabilities. Supporting up to 2048 uncompressed 16-bit, 44.1kHz wav files – the same quality as an audio CD – the WAV Trigger can play and mix up to 14 stereo tracks simultaneously and independently, with very low latency. Tracks can be controlled via 16 programmable trigger inputs, or by using a native serial control protocol or even MIDI.
- MP3 TriggerSKU: WIG-13720 Brand: SparkfunMake some noise with your next project! The MP3 Trigger board is built to make MP3 sound integration easier than ever. The board has 18 external trigger pins that will directly trigger pre-selected MP3 tracks, and a full-duplex serial control port that provides full transport control, remote triggering for up to 256 tracks, and fast real-time volume control. MP3s are stored on FAT16 formatted SDSC or FAT32 formatted SDHC micro-SD flash memory cards. In addition, optimized code can achieve 192Kbps stereo playback from a wider range of cards.
- littleBits Remote TriggerSKU: LBH803 Brand: LittleBitsThe remote trigger lets you use a common remote control with your modules. Make your littleBits circuit and point your remote control at the remote trigger’s sensor. Then, press any button on your remote control to activate the module. The remote trigger will work with almost any button on a remote that uses infrared light to send signals.
- SparkFun Servo TriggerSKU: WIG-13118 Brand: SparkfunThe SparkFun Servo Trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal changes state, the Servo Trigger is able to tell an attached servo motor to move from position A to position B. To use the Servo Trigger, you simply connect a hobby servo and a switch, then use the on-board potentiometers to adjust the start/stop positions and the transition time. You can use a hobby servos in your projects without having to do any programming!
- MP3 Trigger V24SKU: POLOLU-2744 Brand: PololuMake some noise with your next project! The MP3 Trigger board is built to make MP3 sound integration easy. The board has 18 external trigger pins that...
- littleBits Motion TriggerSKU: LBH809 Brand: LittleBitsThe motion trigger is similar to the sensor on an automatic door: when someone is moving nearby, it sends an ON signal to the following Bits. It's very sensitive, so don't breathe unless you want to be detected! Try it with some LEDs to create a security light!
- littleBits Sound TriggerSKU: LBH811 Brand: LittleBitsThe sound trigger listens to the noise level in your room, and sends an ON signal when it gets over a certain level. You can make that threshold louder or softer using the included screwdriver. We like to use it with an LED to light up your room when you snap your fingers.
- Schmitt Trigger - CD40106BSKU: COM-13952 Brand: SparkfunThe CD40106BE consists of six Schmitt-trigger circuits. Each circuit functions as an inverter with Schmitt-trigger action on the input. The trigger switches at different...
- Limit Switch Trigger (1-1)SKU: GB-1207-0001-0001 Brand: goBildaThis Limit Switch Trigger is able to fasten to one end of the 3503-0804-0038 Lead Screw Nut. The profile is matched to that of Open goRAIL.....
- SparkFun Qwiic MP3 TriggerSKU: DEV-19030 Brand: SparkfunThe SparkFun Qwiic MP3 Trigger takes care of all the necessary requirements for playing sound files, all you need to do is send a simple I2C command!...$36.45 AUD, inc GSTAs low as $34.63 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- Adafruit Perma-Proto Super Pack!SKU: ADA591 Brand: AdafruitPick up a super pack of Adafruit's Perma-Proto PCBs, perfect for professional prototyping projects! This super pack contains 3 each of Adafruit's 3 sizes - 9 PCBs total. You'll...
- Super Scissors - PH-51SKU: ADA1599 Brand: AdafruitSave your scissors! Instead of using your nice shears (and dulling them) or wire cutters (not right for the job) - use these super scissors. They're meant for engineering/maker...
- Slow Vibration Sensor Switch (Hard to trigger)SKU: ADA1767 Brand: AdafruitThe "poor man's" accelerometer/motion sensor! These spring-vibration switches are low sensitivity non-directional vibration induced trigger switches. Inside is a...
- Fast Vibration Sensor Switch (Easy to trigger)SKU: ADA1766 Brand: AdafruitThe "poor man's" accelerometer/motion sensor! These spring-vibration switches are high sensitivity non-directional vibration induced trigger switches. Inside is...
- Super Capacitor - 10F/2.5VSKU: COM-00746 Brand: SparkfunYes you read that correctly - 10Farad capacitor. This small cap can be charged up and then slowly dissipated running an entire system for hours. Combine two in series for 5F/5V. Do not over voltage or reverse polarize these capacitors.
- Super Capacitor - 100F/2.7VSKU: FIT0134 Brand: DFRobotThis is a 100 Farad capacitor. Combine two in series for 50F/5.4V. Our testing told us that two of these can power Arduino for 4 hours (with one LED). And you can recharge the capacitor just within 30 seconds.$21.25 AUD, inc GSTAs low as $20.19 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- Pimoroni Super Dinky BlinkySKU: PIM540 Brand: PimoroniConnect some LEDs (and a battery) up to this little square board and watch them blink! SDB also functions as a handy power switch for papercrafts, cards and wearables.$9.50 AUD, inc GSTAs low as $8.84 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- Mini Spy Camera with Trigger for Photo or VideoSKU: ADA3202 Brand: AdafruitIs your house haunted? Or, rather, are you convinced that your house is haunted but have never been able to prove it since you've never had a camera small enough...$27.40 AUD, inc GSTAs low as $25.48 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- Adafruit Music Maker FeatherWing - MP3 OGG WAV MIDI Synth PlayerSKU: ADA3357 Brand: AdafruitBend all audio files to your will with the Adafruit Music Maker FeatherWing! It's a fun-size version of Adafruit's Music Maker shield for Arduino! This powerful shield...
- Adafruit Audio FX Sound Board - WAV/OGG Trigger with 16MB FlashSKU: ADA2220 Brand: AdafruitWould you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want...
- Adafruit Audio FX Sound Board - WAV/OGG Trigger with 2MB FlashSKU: ADA2133 Brand: AdafruitWould you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontrollers, you just want...
- LED - Super Bright WhiteSKU: COM-00531 Brand: SparkfunThese are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the intensity. All lenses are clear.
- LED - Super Bright BlueSKU: COM-00529 Brand: SparkfunThese are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the intensity. All lenses are clear.
Oscilloscope Triggers: A quick what and how
So we have vertical graphing of voltage and horizontal sweep, but our signal is just going to go bananas on our screen if we don't sweep at the same point in the waveform. That's where triggers come in, allowing us multiple ways to fix ou...
Getting Started with Saleae: Tips and Tricks
Well hello there, if you’ve been looking at the amazing line-up of Saleae gear and wondered how to get started with it all, then you’ve come to the right place. Today we’re going to take a look at getting your Saleae setup...
Put the Internet to Work with IFTTT & Particle
We’re in a golden age of connectivity, the internet we know today has given us the tools to connect anything to anything, and now with the platform brought to us by Particle, DIYers everywhere can connect the creations up to this va...
Infrared Sensing, Hardware Interrupts, and the Arduino
Infrared (IR) is a great way of using non-visible light to control electronics, and there are a bunch of modules that we can use with our Arduino. However, what do we mean when we are talking about infrared and electronics? Well, IR remotes...
Ultrasonic Sensing with Pycom
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. One of the most common sensors in...
Makerverse Audio Kit Guide | Play Music and Generate Tones
IntroductionWelcome to the guide for the Makerverse Audio Kit. This kit will allow you to build a music player, a musical keyboard, and a sound effect soundboard! To follow along you will need: The Makerverse Audio Kit The Makerverse ...
Our littleBits Rule Your Room Kit Review
"Yes, I would recommend this a friend." That's the verdict of 90% of people who pick up the Rule your Room Kit from littleBits. We love it so much, we're most definitely recommending it to you and your family. But you don't need to take ...
Raspberry Pi Workshop for Beginners
Welcome to the Raspberry Pi Workshop for Beginners! Here you'll be able to follow along with our series of bite-sized videos that cover everything you'll need to know to get started with your Raspberry Pi, and start making awesome project...
Send a Downlink from Adafruit.io via The Things Network
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. Any good LoRaWAN device can send ...
Raspberry Pi and the IQaudio DAC+ | Volumio and Raspberry Pi OS | Hi-Fi on a Ras-Pi
Flawless high-quality audio output on a Raspberry Pi Single Board Computer! All is achieved by the IQaudio DAC+ HAT. This dedicated DAC lets you enjoy high-quality, distortion-free, artifact-free, low noise, and high-bitrate audio playback...
Temperature Sensing with Particle
If you’re looking for a platform to create your ideal data-logger, then look no further than Particle. Whether it be that you want to build a weather station, or a movement detection system, thanks to Particle’s 3G and Wi-Fi boa...
Let's take a look at Makey Makey!
Makey Makey is a compact circuit board which allows you to create circuits using anything you like and connect them up to a computer. You use alligator clips to connect things to the Makey Makey, and then your Makey Makey connectors to a co...
How to set up a PiHole on a Raspberry Pi - Block All Ads and More!
Time to create a Little Red Advertisement Devouring Monster. This will be a self-hosted, network-wide, ad-blocking system running on a Raspberry Pi Single Board Computer. It will also stop access to malware sites and phishing websites. Fur...
Getting Hands-on with Sensors
What good is a robot if it can’t interact with the environment around it? Sensors are the backbone of almost every electronics project as they allow your program to make decisions based on external stimuli. We’ve got sensors for...
PiicoDev Real Time Clock (RTC) RV-3028 - Getting Started Guide
This guide will help you get started with a PiicoDev Real Time Clock. We'll set and read the time/date, observe the power-backup capability, and configure the RTC with an alarm. A Real-Time Clock (RTC) is a timekeeping device that accurat...
How to Make a Safe Shutdown Button for Raspberry Pi
Pulling the power to your Raspberry Pi can cause image corruptions & other issues that can damage your Pi! In this article, we will create a small push button that will work as a ‘Safe-Shutdown’ option. We’ll connect i...
Solarbotics Paris Flyer CarouSol Kit Speed Build
We had a lot of fun making this speed build video for the Paris Flyer CarouSol Kit by Solarbotics. If you aren't already familiar, Solarbotics makes a great line of DIY electronics kits made from laser cut materials. They range from quite s...
Capacitive Touch with Makey Makey
The Makey Makey introduces the concept of using everday objects like fruit, lead pencil drawings, play dough etc. to interact with your computer via USB. The Makey Makey acts like a HID device over USB, which means that it behaves just like...
8Bitdo Zero Controller Review
It’s always a fun day when you get hands-on with a device as cool as the 8Bitdo Zero Bluetooth gamepad. 8Bitdo are known are for their re-creations of classic gaming controllers such as the SFC30 and NES30 which bring the magic of NES...
Circuit Scribe for Educators
Educators everywhere are lining up to have the most recent, high-tech teaching tools to introduce STEM learning in the classroom. With the rate that modern technology is advancing, educators can often feel overwhelmed with the sheer number ...
Using your Arbitrary Waveform Generator
By now you are aware that when it comes to measuring electronic signals, oscilloscopes are what you are going to be using. However, if you were providing a circuit with a particular signal, a function generator is the perfect tool for tha...
DIY 10W Bluetooth Speaker - No Code Needed – How to use a Bluetooth 4.2 Audio Receiver Board with Onboard Amplifier (MH-M38)
Let's turn it up to 11! Today we are getting right into Bluetooth Audio Receivers in particular the MH-M38. The MH-M38 is a stereo audio receiver with loudspeaker outputs (and an inbuilt amplifier) that can play music from a smartphone/com...
Effective Ways To Detect People Using Common Sensors
In this guide, we'll look at common methods of detecting people and some of the different sensors you can use to detect people in your next project.Sensors covered in this guide: PIR Sensor RCWL-0516 Microwave Radar SEN0395 mmWave Rad...
Makey Makey in the Classroom
Hey guys, if you’re looking to get the creativity and fun of Makey Makey into classrooms or workshops, then you’re in the right place! Makey Makey is an incredible tool for educators to get kids thinking about how they can use t...
Say Cheese with Raspberry Pi Camera
Ever thought it would be cool if your Raspberry Pi could see the world like you do? You’re in luck, camera support is an integral part of the Raspberry Pi hardware, it comes with a built in CSI connector for connecting camera ...
How to Use Speakers and Amplifiers with Your Project
A popular question that we get all the time is ‘How do I choose a speaker or amplifier to go with my project?’. It’s a good question, and if you’re not familiar with the terminology, it can seem a bit daunting to kno...
Our Rigol DS1052E Oscilloscope Review
The 2-channel Rigol DS1052E oscilloscope is beloved by many as a really decent, cheap 'scope for the home electronics lab. While its features pale next to those hosted by more modern offerings, the 1052 packs the basics into a reliable...
Pose Estimation and Face Landmark Tracking with Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto yo...
All About Electrical Switches
On and Off. It’s the basis for all electronics, from the most sophisticated computer network to a simple circuit. Electronics is all about using one thing, to control another, input and output, on and off. Even the transistors inside ...
Control Large GoBILDA DC Motors With a Raspberry Pi - Pololu Motoron HAT
This guide will demonstrate exactly how to control any large DC Motors that we stock with a Raspberry Pi Single Board Computer, through code or through a Bluetooth Controller. To clarify (in my mind) a large DC Motors runs at 12+ Volt...
Best Glue for 3D Printed PLA Parts and a 3D Printed Ukulele
Whenever you want to print larger than your 3D printer build space you are going to find yourself wanting to combine 3D printed parts together. Furthermore, as you wrap your head around 3D printing, you learn to save on filament by printing...
How to Use HC-05 Bluetooth Modules
So we’ve taken a look at what Bluetooth is in our Introduction to Bluetooth tutorial, and hopefully, you’ve found our Choosing a Bluetooth Module For Your Project tutorial useful in deciding which Bluetooth module is right ...
PiicoDev Capacitive Touch Sensor CAP1203 - Raspberry Pi Guide
Let's get started with the PiicoDev® Capacitive Touch Sensor. In this guide, we'll connect the PiicoDev Capacitive Touch Sensor to our Raspberry Pi and get it working with some example code to detect touch events. We'll also remix the c...
Which Raspberry Pi Case is Best For You?
What’s even better than the world’s most popular microcomputer sitting on your desk? When it’s sitting there in a case which protects it, makes it easier to use, and gives your desk some style. If you buy a Raspberry Pi i...
Gaming Kit for RetroPie
Video gaming has evolved tremendously over the last decade, console games produce near real-life graphics, and playing with friends across the globe is easier than sending a text message. This is all well and good, but there are those of us...
Set Up a Geophone with a Raspberry Pi and an ADC (ADS1115)
Geophones are devices that generate electric signals proportional to the particle velocity in a sound/compression wave. More simply a Geophone is a super low frequency microphone for the ground. Geophones are used around the world to measu...
How to Create a NOOBS microSD Card
NOOBS has made installing Operating Systems (OS) on the Raspberry a super simple process. If you haven’t purchased a Raspberry Pi NOOBS MicroSD card, you can download NOOBS onto a blank SD card in a couple of quick, easy steps. ...
Using NeoPixels with Particle
Life’s better in colour right? Then why are you still using boring old regular LEDs in your project, when you could be using addressable RGB LEDs. Now LEDS that have Red, Green, and Blue integrated in a single package are nothing new,...
Lightning Sensor with a Raspberry Pi Single Board Computer - 40 KM RADIUS RANGE!
What if I told you that you could have the power to detect a lightning strike from 40km away? You'd probably think I've gone mad watching too many Marvel movies. But it is true! All thanks to the DFRobot Gravity: Lightning Sensor. Accessib...
Raspberry Pi HATs
Yep, Raspberry Pi is a very cool platform, so cool that they offer a range of stylish HATs to go with them. No not headwear, but fully functional hardware modules that are designed to plugin directly to the Raspberry Pi GPIO headers, and op...
Our Rigol DS1054Z Oscilloscope Review
The quality and features in entry-level 'scopes has made a huge jump in recent years - In a nutshell, the 4-channel Rigol DS1054Z oscilloscope delivers tremendous bang for your buck. The DS1054Z is so well outfitted, I'd b...
Chibitronics at Home - STEM Starter Kit
Now that we have dipped our toes into the Chibitronics environment, let's take a look at a more in-depth kit and see what kind of projects it offers. The Chibitronics STEM starter kit comes with: 1 Circuit Stic...
Raspberry Pi Kodi Media Centre
Media centres are everywhere nowadays, from smart TV’s with built in media apps, to standalone lounge room boxes to watch all your favourite shows on. With the new features found on the Raspberry Pi 3, it makes sense for it to become...
Getting Started with Particle Internet Button
Slowly but surely the electronics industry is moving away from discrete microcontrollers and towards boards that have sensors and extra functionality built in. This means that rather than buying a microcontroller and then needing to connect...
The Things Network, IFTTT, and BEYOND!
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. Connecting your Pycom Lopy4 or an...
Our Rigol DS1104Z Oscilloscope Review
The 4-channel Rigol DS1104Z oscilloscope is a 100MHz powerhouse. The DS1104Z is almost identical to its little brother, the DS1054Z, but brings to the table twice the bandwidth. The 1000Z line of oscilloscopes from Rigol is one...
Read-Only Raspberry Pi - Never Corrupt your Micro-SD Card
Here is a solution so you can turn your Raspberry Pi handheld computer on and off from the power plug (power cycle it) just like any other appliance in your home! And it can all be done through only one setting. With a normally set-up Rasp...
8Bitdo Controller Modes
8Bitdo controllers are the best retro-gaming controllers you can buy. You could pick one up for your RetroPie gaming system so you can relax back on your lounge with your wireless gaming controller. We did a great write up on the process of...
PiicoDev Mounting Guide
This guide is all about mounting PiicoDev® Modules. It covers how to mount modules to PiicoDev Platforms (or any other material up to 3mm thick), and shows the common dimensions and mounting-hole patterns for PiicoDev hardware...
How to use a PiRelay HAT for Raspberry Pi - Multiple Relay Control with Voice or GUI
This guide will teach you exactly how to use a Raspberry Pi Single Board Computer to independently control 4 relays. A Relay is an electrically operated switch. This is all possible thanks to the PiRelay V2 HAT from SB Components. These re...
Controlling a Solenoid with Raspberry Pi and a Relay
Here is how to control a 12 Volt Solenoid with a Raspberry Pi using a 5 Volt Relay. Solenoids are an immensely useful way to turn electrical energy into a linear motion. Solenoids come in a variety of different specifications with 5 Volt an...
Prototyping a Circuit: Methods and Tools
Ah prototyping, the backbone of maker electronics, well really all electronics. Any successful device, product, or idea doesn’t just appear as a finished concept, it goes through stages of product and one of those is prototyping. In f...
Pico Armour - A 3D Printable Case for the Raspberry Pi Pico
A super quick article for those who just got their hands on the Raspberry Pi Pico and want to keep it safe and snug in a case. Either with a resin printer or fused filament printer both can produce excellent cases. It was very pleasant prot...
Getting Started with Particle Electron
In another tutorial we looked at the Photon board from Particle, and whilst Wi-Fi is awesome for many applications, it restricts you to a localised connection. Particle have once again come to rescue and provided us with a cellular solution...
Our Lulzbot Taz 6 Review
Lulzbot is constantly building upon their printer's design, incorporating the best modifications and add-ons from the community into their newer models. In May 2016, their newest addition to the TAZ line of printers, the TAZ 6 wa...
Teensy Boards Compared
Hello everyone, how awesome are the Teensy boards from PJRC? Super awesome. And as with any product that has been around for a few years, and gone through various iterations, there’s now a few different boards to choose from, which ...
WS2812 / NeoPixel Addressable LEDs: Arduino Quickstart Guide
This tutorial is aimed at getting some instant gratification from your WS2812 LEDs (also known as NeoPixels). I'll briefly cover a bare-bones setup for Arduino. If you've never used an Arduino before, we've got you covered with our free, o...
8Bitdo NES30 Pro Controller Review
Today, we’re looking at the 8Bitdo NES30 Pro. It’s a newer controller from 8Bitdo and one that I’m really excited about. It’s an interesting gamepad, with the styling and form factor taking cues from both the classic...
Pi To All The World With GPIO
So you’ve got your Raspberry Pi. You’ve gotten NOOBS setup on it, explored Raspbian a bit, and you’re feeling like a bit of a pro. Awesome! Now let’s get down to the nitty gritty side of things, what it’s ...
Graphic OLED Displays with Particle
Note that the digital artifacts on the screenare from the camera used to capture and not the screen itself How many great artworks or photos have you seen that consist of just lines of characters; words and numbers? Very few. It’s ...
Getting Started with Raspberry Pi Pico
This guide is a little outdated: Follow our updated guide for a much simpler way to get started! Contents Part 1 - Interacting Coding with the REPL Part 2 - Moving Beyond the REPL (with rshell) Part 1 - Interactive Coding with the...
DIY Magnetic Encoder
The PiicoDev Magnetometer unlocks a lot of sensing abilities for your project. In this guide we'll walk through how to sense an angle with a small magnet and print the angle on a PiicoDev OLED. This guide covers what the sensor is r...
Natural Disaster Sensor Project with Circuit Playground Express
There is some wild weather approaching! We need a way to give ourselves an early warning when a disaster strikes! In this project, we will use the Adafruit Circuit Playground Express to make an all in one Disaster Detection Station that wil...
Remote Sensing with Particle Electron
Hey guys, how much fun are microcontrollers? They’re your own miniature slave to do your bidding in whatever way you choose, however as fun and all as using them to do math and crunching numbers, the real joy is seeing them interact w...
Basics: Writing Your First Script with Raspberry Pi
In this tutorial we'll be writing our first bash script for Raspberry Pi. We'll create a directory to keep this and future scripts, write the actual script, and set it up as something that can be executed from the shell. Scripts are an inc...
Arduino Projects with Motion (Using Sparkfun RedBoard)
Arduino Projects with Motion (Using Sparkfun RedBoard) Welcome to the Third Project Set from the Sparkfun Inventors Kit V4.0 Guide! In this tutorial, we will explore the operation of a Servo Motor and an UltraSonic Sensor in combination wi...
Programming with USB-Serial Converters
Thanks to huge advancements in technology over the last decade, the maker community that we know and love has thrived. It’s now easier than ever before to get started with programming and tinkering due to the innovation from brands su...
Video Looper with Raspberry Pi 4 Model B
[Update: The OMXPlayer system, needed for the video looper, has been dropped with the recent 'Bullseye' Raspberry Pi OS. Updates are coming out fast and all the teething troubles from this new OS will be ironed out. For now, download and f...
Rigol's PC software: Ultra-Sigma and beyond
The ability to connect your test equipment to a local PC is invaluable. It allows monitoring and the use of your equipment via a PC interface. That includes coveted mouse/keyboard control! This control centre capability is essential when yo...
Basics: Getting Started with the Terminal on Raspberry Pi
In this tutorial we’ll be getting familiar with basic use of the Raspberry Pi terminal. We’ll cover navigating the file-system, making directories, writing and editing text files, and just touch on the use of wildcards. To get ...
Make 3D Prints Look Like Chrome and Steel - Metallic Paints and Finishes For 3D Prints
Demonstrated here are two metallic finishes, that you can do to any 3D print, that will astound your friends and family when you tell them 'It was actually 3D printed and these are not metal at all'. These finishes are perfect to use for co...
Switches, Debouncing and the Arduino
When we boil it down, everyday interactions with electronics are usually limited to controlling stuff with switches. Whether it be turning on the lights, switching on your laptop or turning on the kettle, all examples of how a physical sw...
PiicoDev Capacitive Touch Sensor CAP1203 - Micro:bit Guide
Let's get started with the PiicoDev® Capacitive Touch Sensor. In this guide, we'll connect the PiicoDev Capacitive Touch Sensor to our Micro:bit V2 and get it working with some example code to detect touch events. We'll also remix the c...
I2C with Raspberry Pi
Hello there, how’s your day been? Good? Fantastic! Not so good? Don’t worry it’s about to get a lot better, because today we’re going to take a look at how to use the I2C interface on our Raspberry Pi to control I2C ...
How to Use a Logic Level Shifter/Converter
So you’ve got your microcontroller/development board ready to go, you’ve got your sensors and external components and you’re ready to build an IoT device to make the world your slave. But hang on a minute, the sensor you h...
Our 8Bitdo SF30 Pro Controller Overview
The 8Bitdo SF30 Pro was launched at the end of 2017 by 8Bitdo in an effort to create the ultimate, ‘portable’ gaming controller. Having become known for their faithful recreations of vintage gaming controllers, the SF30 Pro is a...
PiicoDev Capacitive Touch Sensor CAP1203 - Raspberry Pi Pico Guide
Let's get started with the PiicoDev ® Capacitive Touch Sensor. In this guide, we'll connect the PiicoDev Capacitive Touch Sensor to our Raspberry Pi Pico and get it working with some example code to detect touch events. We'll also rem...
Makerverse Real Time Clock with Supercapacitor Backup - Raspberry Pi Pico Guide
Introduction This guide covers the basic use of the Makerverse Supercap Real Time clock on the Raspberry Pi Pico using our RV3028 MicroPython module. The MicroPython module implements some commonly used features of the RV3028 RTC but is no...
Getting Started with Home Automation Using MQTT
What is MQTT? MQTT (Message Queue Telemetry Transport) is a simple and ‘lightweight’ way for internet-connected devices to send each other messages. This is important for home-automation because devices need to send messag...
Using USB and Bluetooth Controllers with Python
The Raspberry Pi is an amazing piece of technology, and it’s the platform of choice for all kinds of projects. Something that makes it great is the integration of complex hardware that is taken care of for you. For example, if you wan...
Object and Animal Recognition With Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto yo...
Cooling Your Raspberry Pi
Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what you can do with it if you take a look under the hood. One of the most popular experiments to do with your Raspberry Pi is o...
Detect Speed with a Raspberry Pi, Camera and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Mi...
Pan-Tilt Hat with Raspberry Pi - Quick Start Guide
Pimironi Picade Pan-Tilt Hat lets you mount and control a pan-tilt module right on top of your Raspberry Pi palm-sized computer. Setting up a Pan and Tilt system has never been easier with absolutely no soldering required! Pe...
Hand Recognition and Finger Identification with Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto y...
Our Review of the MOARstruder by Lulzbot
Toolheads for your 3D printer come in all shapes and sizes. The different models available from Lulzbot are all designed with a specific purpose in mind, usually to add a filament type to your 3D printing repertoire. Dual extruders enable y...
Raspberry Pi Compute Module Generations 2020
Raspberry Pi Compute Modules have developed in tandem with the many generations of Raspberry Pi single-board computers. These boards are in every right a microprocessor just like their bigger cousins however they are a very different form f...
Solar Powered Raspberry Pi 4 Model B
This is going to be easier than you thought (or at least much easier than I thought)! Today we will create a Raspberry Pi 4 Model B UPS PiJuice System that will be completely powered by a Solar Panel. It's coming up to winter over here so I...
How to Conserve Battery Life with IoT Projects
If you’ve ever created a project that uses batteries, you’ll be well aware how hard it can be to decide on elements in the project which can affect the battery life. You end up ‘umming’ and ‘ahhing’ for a...
Maintaining a Project with Git
Let's have a very quick look at Git and Github - Git is an enormous topic, so this won't be an exhaustive tutorial but by the end of it we'll have a working knowledge of basic git workflow. I'll be showing this tutorial on a Rasp...
Teensy 3.5 & 3.6 Review
When Teensy was first released, it was a revelation to the maker community. It brought together the power of ARM processors and the simplicity that is the Arduino IDE. Building upon that platform, Paul Stoffregen, the man behind PJRC contin...
3D Printing for the Circuit Playground
You’ve made yourself a great project for your Circuit Playground Express, now all you need is a box to put it in. How do you keep your Circuit Playground safe in a housing while still being able to press the buttons and use the sensor...
DC Motor Control with an Arduino
Electronics is fun, so far we have covered off on communicating between devices, making LEDs flash and LCD screen operation. However using electricity to control some form of movement in your project is a fun and interesting aspect to inves...
Our tips for using NiMH Batteries
NiMH is an abbreviation for Nickel-Metal Hydride. NiMH batteries are some of the most common rechargeable batteries we see in consumer electronics. Due to their superior chemistry, NiMH batteries have taken over Nickel Cadmium Battery appli...
How to use Force Sensitive Resistors with a Raspberry Pi and a ADS1015 ADC
Force-sensitive resistors (FSR) are remarkable electrical components and are proper unsung heroes in the Makers World. Name me a better variable touch input device which has basically no moving parts, all whilst being available in such a t...
Choosing Your Next LiPo Battery
As technology gets smaller and more powerful, wearables and portable devices are becoming more common in our everyday lives. Makers are looking to make projects portable and with that comes the need for high capacity batteries that are reli...
How To Control A Motor with the Raspberry Pi
In this tutorial, we are going to connect a Motor to the Raspberry Pi and create a hypnotic self-spinner. We are first going to look at how to wire the Raspberry Pi to the motor controller and the motor. We will then look at using the raspb...
Getting Started With Relays | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Relay is, why we might use one, how to choose a Relay, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A 5V SPDT Relay - I'll be using a 5V Single Channel Relay M...
Swell Python Scripts with the Turtle Library
Time to flex some of the coding muscles we have gained. Using the knowledge we have with Python, this guide will go through the creation of interesting and dynamic graphic animations. The first codes in this tutorial are generators for geo...
The Lulzbot 3D Printers: Mini vs Taz
Hailing from Aleph Objects in Loveland, Colorado, the Lulzbot range of 3D printers are world renown for their quality, reliability and ease of use. The reason they're so popular? Apart from the gilded Lulzbot technical support (practically ...
PiicoDev Button | Getting Started Guide
Buttons are a ubiquitous user interface - of course, you've seen them everywhere! The humble button is often the fastest way to create a control interface for your project too. This guide will help you get started with a PiicoDev® Butt...
PiicoDev RFID Module - Guide for Raspberry Pi Pico
Radio Frequency IDentification (RFID) uses electromagnetic fields to identify and communicate with tags. Each RFID module emits radio waves that energise the passive tag, which then responds with its own identifying number or data, as reque...
PiicoDev RFID Module - Guide for Raspberry Pi
Radio Frequency IDentification (RFID) uses electromagnetic fields to identify and communicate with tags. Each RFID module emits radio waves that energise the passive tag, which then responds with its own identifying number or data, as reque...
How to use Stepper Motors and DC Motors with a Raspberry Pi - Adafruit DC & Stepper Motor HAT
This guide will demonstrate exactly how to control Standard Stepper Motors and DC Motors with a Raspberry Pi Single-Board Computer. To do this as seamlessly as possible we will utilise a HAT. HAT stands for Hardware Attached on Top. HAT bo...
Raspberry Pi Pico with LoRaWAN and The Things Network - Makerverse LoRa-E5 Module - Transmit Weather Data into IoT
Feel restricted by your connectivity? Want to send data from a remote node 10km away from civilization? Or ~3km when you are in a built-up civilization. Feel the urge for Liberation? Then I have the solution for you! Using only hardware bu...
Using Relays with Particle
So, you want to control things with your Particle Photon and/or Electron do you? Well, a relay is a perfect way to do that. Whilst there are many ways to control an electrical signal from digital logic such as transistors and optoisolators,...
Motor Drivers vs. Motor Controllers
If you’ve ever built a robot with wheels, or any motorised parts really, you’ll have come across the issue of needing to drive it from your microcontroller. Because a standard chip is only able to output a small amount of curren...
E-Textiles / Wearables Compared: LilyPad vs GEMMA vs Microbit
Every good E-Textiles or Wearables project needs to start somewhere, and the natural starting point for any project is choosing the right microcontroller. There are many good choices out there, and we will compare a few of the best and brig...
Understanding ESP32 Naming Conventions
Espressif is a constantly ground-breaking company that produces lots of really cool development modules which includes the ESP32. ESP32 Boards, ESP32 Dev-Kits, and ESP32 Modules (the part that gets soldered to the Board/PCB) are all about ...
4G and GPS HAT For Raspberry Pi - Waveshare SIM7600X
Love your Raspberry Pi but wish it had even more connectivity akin to your mobile phone. Then the Waveshare 4G HAT is the solution for you! HAT simply means Hardware attached On Top. With this installed on your Raspberry Pi Single Board Co...
PiicoDev Ultrasonic Rangefinder | Getting Started Guide
Similar to how bats echo-locate and how submarines use sonar, the PiicoDev® Ultrasonic Rangefinder uses sound waves to measure the distance to an object. It sends out a high-pitched sound wave, which bounces off of the object and comes...
More Exciting Features - Ultimaker Cura
Cura is constantly being improved upon and half the fun is keeping on top of all the new changes and new offerings it gives. For completely free software, they are doing an amazing job. Nailing the recipe for a 3D prints will let you get th...
Circuit Playground Express Workshop for Educators and Beginners
Welcome to the Circuit Playground Express Workshop! This workshop is geared toward educators and coding beginners, who want to get started programming with this easy to use platform. We will go over everything you need to know to get you st...
Integrated Computer Vision Package - OAK-D Lite With Raspberry Pi Set Up
If you ever needed a performance boost when running Machine Learnt AI Systems (like facial recognition) with a Raspberry Pi Single Board Computer then I have a solution for you. The OAK-D Lite. The Oak-D Lite is the Leatherman Multi-tool o...
Getting Started with Servos | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Servo is, when we might use one, how to choose a Servo, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A Positional Servo, such as the Feetech FS90 Micro Servo A Con...
Cura 2: LulzBot Edition - An Overview for Beginners
Now that we are all on track with our Slicer software, having just installed Cura 2 and upgraded our printer firmware, let's work on turning some 3D Model files into G-Code for our 3D Printer to create. We're going to be using our LulzBot M...
DFRobot 8.9 Inch 1920x1200 IPS Touch Display For Raspberry Pi - Set Up Guide
It is time for a high-quality, complete package, 1920x1200 (HD) display set up with a Raspberry Pi Single-Board Computer. In regards to touch screens with Raspberry Pi have looked at Tiny GPIO HAT LCD displays, medium-sized AMOLED maker di...
Arduino Boards, Compared
We're going to compare each of the Arduino Boards available to Maker's and Electronics Enthusiats. We'll discuss the features of each board, provide an informative pinout diagram with tonnes of detail, and toward the end of the article, pro...
Makerverse Motor Driver, 2 Channel - Application Guide
Introduction The Makerverse Motor Driver has been updated to a v20 design which now features a 5V output pin instead of the VM pin. Some images and in-video descriptions in this guide may be outdated This guide covers the use of the Maker...
Analog Electronics Crash Course
Welcome to our beginners tutorial on analog electronics. Living in the digital age that we do, it’s easy to disregard the world of discrete analog components, however these concepts form the basis for everything from your mobile phon...
Waveshare 5.5 Inch AMOLED Screen for Raspberry Pi
Ever wanted a pocket computer with a Full HD screen (1080x1920)? Love tiny GPIO screens like this 3.5 Inch from Waveshare but want one that is a little bigger and higher resolution so that it is easier to read? Or want a really premi...
IoT with LoRaWAN, Pycom, The Things Network & Node-RED
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. In our two previous Pycom article...
Pycom Expansion Board - Getting Started
Where do I start? If you’re new to programming Python is a great place to start! I’ve seen Python taught to primary school age children and I have used Python in a Machine Intelligence course at university. It’s no wonder...
Face and Movement Tracking Pan-Tilt System with Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS ...
PiicoDev Transceiver | Getting Started Guide
A radio transceiver is a device that can both transmit and receive radio signals, making it the perfect tool for communication on the go and remote projects! The PiicoDev Transceiver™ is a 915MHz radio that can send short messages up...
C Programming for Makers
Welcome to the C Programming Workshop for Makers! Here you'll be able to follow along with our series of easily digestible videos that cover everything you'll need to know to on your way with C programming and start making awesome projects....
Super cheap Xbox 360 wireless adapter
This project is to build a super cheap wireless adapter based on Raspberry Pi Zero and ENC28J60 ethernet module for Xbox 360I have two Xbox 360 consoles and today I want to connect them together but I only have one OEM wireless adapter. It ...
Cosplay Blaster
Hey guys! First time poster. I've been working on a blaster for my girlfriend's costume, and I thought I would share it with everyone. When triggered, it plays a selected sound effect and flashes the light. Pretty simple :)So, this is my fi...
p0wer - Control mains outlets over wifi.
As part of a larger home automation project, I wanted the ability to control some mains power outlets remotely. To achieve this, I interfaced the transmitter from an inexpensive 433MHz mains remote control kit with a raspberry pi zero w (vi...
Smart Home Makeover with HomeAssistant
IntroductionI wanted to bring ageing, and failing, Home Automation infrastructure into the modern age whilst retaining hardware investments already made. Our house had Universal Power Bus (UPB) dimmers and switches installed at build time...
Duck Off! A Duck Repellent Device
Introduction
We live on a rural property and have around 20 to 40 wild ducks around at any one time. We have a large dam and jetty, however it is almost unusable due to all the ...
The Great Doorbell Hack
Do you want a quick, easy, cheap RF remote control for your Raspberry Pi projects? Well, look no further than the front door! As you've probably got a half-duplex RF setup you've never considered using in a project before. Try this simple h...
Hyperweb: Interactive Art for Vivid Sydney
Hyperweb is a collaborative interactive sculpture installation at Vivid in Sydney. I designed and built a crowd sensing weather station that is used to control an audio "soundscape" within the piece. It also triggers light show events that ...
IoT Plant Monitor
So, my wife wanted to have some small plants in the house. I didn’t, so we compromised, and got some plants. The only thing is that neither of us remembers to water them, so I wanted to build a sensor array to monitor the moisture con...
Autozem
Introduction So now everything is available in this day and age, and all those childhood dreams can now come true as parts, technology and software has come a long way. I had recently taken up the hobby, RC planes. Eventually I learnt ho...
LoRaWAN Tank Level Sensor Node
My brother-in-law has a dairy farm in Victoria and many hours per week are wasted traversing the farm to check water tank levels, opening/closing valves, and other small tasks that could easily be remotely monitored and controlled. It was ...
Backyard Birdcam
Introduction
I had been thinking about how best to capture clear close-up photographs of some of the many birds we see around our property for quite a while and mulling over a variet...
Mailbox Delivery Notification System
Introduction
During the Covid lockdown, I needed something to do. The Postman or woman does not deliver mail every day as most bills come online. So I built this to notify me when the Pos...
mintyPi
This is an awesome project that takes about 6 hours to complete. Hours upon hours of endless fun thereafter! Ideally, some prior soldering experience is advantageous but if you take your time and practice before you start it's beginner fri...
Micro:bit Random Selector
This project has been created to be used as an exemplar for Year 7 Technology students to demonstrate some of the features and potential of making with a micro:bit. This device is a teacher tool or game accompaniment device that random...
Simulated Parisians: Little Autonomous Pedestrians
Introduction
Parisians is a cute simulation of Paris with autonomous pedestrians. It’s simple to build and easy to personalize, a Single Board Computer "wall piece": on display and looping ...
WiFi Garage Door Controller with Raspberry Pi Pico W
I strapped a Raspberry Pi Pico W to my garage door motor and now I can control my garage door from my phone! The Pico W hosts a simple webpage on my local network with three control buttons - one for Up, Stop and Down. Pressing one of...
Garage Door Sensor
This project uses a US100 ultrasonic distance sensor to detect instances of a garage tilt door being left open and sends an alert via the IFTTT mobile app. Additionally, the device logs temperature and pressure to a Thingspeak channel using...
Cosmic Array
An array of individual cosmic ray detectors distributed across a landscape to display how cosmic rays arrive as showers of muons. It's all powered by a Raspberry Pi Zero!This project deployed 16 individual cosmic ray detectors on the banks ...
safePower
I like working with the Pi Zero W and Pi 4 as they are very compact, very powerful and very cheap for the capability they offer. I want to use them on small projects, stand-alone, and can't always guarantee power. As we know most Pi's don't...
Rain Gauge Data Logger
Summary A Raspberry Pi 3B is used to collect digital counts from an electronic rain gauge (1mm of rain per reed switch closure by magnetic see-saw). It has been running without issues for over 12 months. A UPS powers the Pi so it is immune...
Sound Effects Button
The idea for this project came when a friend of mine flew over from Western Australia to visit, and during his stopover in Adelaide, he did what any adult would do; visit the airport novelty store and buy some random stuff. It was pretty mu...
Makey Makey Skill Tester
This is the third project I've put up using the Makey Makey, and it's incredible fun, but it's also the simplest. Today I'm going to show you how to make a simple Skill Tester game complete with sound effects using a Makey Makey board and s...
A 3D Printed Ukulele
Here is a project I just could not help myself but build. A 3D printable Ukulele with a body as large as I could fit standing upright on the printers here. The intention was to make it as large as possible, using no supports, and without th...
Aircraft Lighting Model
The aim of this project was to create a working model of the aircraft exterior lighting systems. Initially, this started as a simple project for Uni, but I wasn’t having that. I wanted to learn something. So of course, I went over the...
Smart Watering System
Introduction This began as an idea after building a very basic single-channel unit. Commercial smart watering systems use a Wifi connection to the internet and get weather reports to determine the level of watering required. These systems...
IoT House
These days we can do just about anything on our phone, we can control so many aspects of our lives using the technology in our pocket, but the most mundane aspects of our lives; opening the garage door, blindly reaching for the light switch...
Roverling
Introduction
My first 3D printer was a CTC generation 2 clone of MakerBot ‘The Replicator Dual’, circa 2012. It died a little while back and has since been replaced ...
BuzzBox
Do you ever wanna pump up some tunes but you don't know how to play a MIDI file? Fear not, the PiicoDev Buzzer modules let you stack up multiple tones into a song. Find your MIDI, export it through a script, upload it and get grovin'! ...
Raspberry Pi Steam Link
Turn Your Raspberry Pi into a Steam Link Sometimes Retropie just isn’t enough to get the best possible gaming experience with the Raspberry Pi. I originally purchased the Raspberry Pi 3B+ so that I could install Retropie and Kodi to ...
Time lapsing in OctoPrint (Properly!)
Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosure, I'm just about ready to turn on some serious 3D printing work. But before I dive into that endless pool of fun, it's a good time to take ...
Fruit and Veggie Gaming Controller
In preparation for some Maker Faire's we were heading to last year, I wanted to combine the awesomeness of the Makey Makey platform, with the fun that is RetroPie. For those who don't know the Makey Makey, it's a fantastic platform that all...
IoT Mailbox
Getting letters and parcels is awesome, what’s not so awesome though is when you miss the postman and you don’t know if that important bit of mail arrived or not. Such a frustrating, yet mundane problem can be solved by creating...
HUGE LED Pixel Panel
I’ve always been fascinated by LED screens and seeing beautiful colours mix and merge to create vibrant displays. I also love games, so what better way to combine the two than a giant LED pixel matrix which can play games, display aud...
Basic Weather Station
The aim of this project was to provide a cost effective and basic weather station for my backyard that can upload readings to Weather Underground. Part 2 of the project will be using this local data to trigger activities in and around my ho...
Smart City Tunnel with PiicoDev
Tunnels are a critical part of road infrastructure and they feature some pretty cool tech. This Smart Tunnel project demonstrates some of the technology involved and how some real-world problems might be solved. Features RFID Trip...
GlowBit Desktop Audio-Visualiser
Introduction
I’ve had this little 8x8 Glowbit matrix for a few weeks now, and for whatever reason, the first thing I thought after running the example programs was “This needs to be synchro...
Tweeting Pi-Zero-W GIF Camera
I made a Raspberry Pi camera that captures GIF files and optionally tweets them over WiFi! It's built around a Raspberry Pi Zero W and a Pi Camera module. The camera connects to a pre-programmed WiFi network to tweet the gifs, but...
Hogwarts Lights
Although there are commercially available lighting kits for Lego models, we found those that are available for this Hogwarts Castle can seem a little garish and don’t do the best job at concealing the wires. We felt that with t...
Makey Makey Pencil Piano
After seeing how much fun people had using the Makey Makey as a gaming controller for our RetroPie setup, I decided that more fun, simple projects that can be made using household materials were in order. So today I present to you the piano...
Borg Cube for Scouts STEM Camp
Introduction
What does one make for a Startrek-themed STEM camp for Scouts? Especially when given the Search and Rescue (SAR) activity base to run. Why this base you ask? Usually I run a radio d...Introduction
What does one make for a Startrek-themed STEM camp for Scouts? Especially when given the Search and Rescue (SAR) activity base to run. Why this base you ask? Usually I run a radio d...
Raspberry Pi Rain Radar and Weather Display
[Update – Until there is correct compatibility of NPM with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Micro-...
RPi Garbage Bin Reminder
Our local council picks up recycling bins one week and green waste the following week. Sometimes people forget which bins go out each week and perhaps they mistakenly put the wrong bins out. Not that that has ever happened to me of course! ...
Hogwarts Legacy Broom Flight Controller
Introduction
I embarked on this project to enhance my interactive and immersive experience with the video game "Hogwarts Legacy," as a devoted Harry Potter fan. Initially, I used a Kano wan...
RPi Cluster - SETI@Home
I was interested in creating a RPi Cluster to learn about how they work. After getting the clusterhat and Pi Zero Ws I set about creating the images for 5 sd cards. This seemed a waste so I scrapped that idea and setup the image for one sd ...
Nintendo Wii Portable | Project G-Wii
Do you love your Wii and its ability to play all GameCube games perfectly but wish you could take it on the go like a Gameboy?
Well, I definitely did and if you're like me so do you. And here is the right place...
Do you love your Wii and its ability to play all GameCube games perfectly but wish you could take it on the go like a Gameboy?
Well, I definitely did and if you're like me so do you. And here is the right place...
The Euclidean
I'm an amateur musician but a pretty serious classical & jazz pianist, and this project arose out of my interest in exploring the difference between writing music for synthesisers and music for piano. I work as a mathematician, so...
Hydra Bluetooth Speaker
Wow - this is one monstrous sounding and great looking speaker - even if I do say so myself! This is basically a 2.1 (stereo + subwoofer) system made with 3D plastic parts. Both the full range and subwoofer speakers are based on closed (se...
Quadbeest - A Flying Strandbeest
Introducing to you today, the Quadbeest, the next evolutionary step in the Strandbeest genealogy. It seemed to be about time for Strandbeests to evolve to take over the air, so I made it happen. Able to be controlled over a kilometre in the...
Kid’s Music Box
I want to make a portable music box that my 2 year old kid can operate intuitively on her own. So, Spotify or any other on-demand music platform with tablets and Bluetooth speakers are out of the question. Remember the good old days of putt...
Remote Automation With a W5100 Shield
This is an Arduino project using and ethernet shield for remote control of a set of relays. The IPControl module was meant to be a simple web accessible device controller. It sort of grew! A little out of hand as you will see...
Identify Birds through Sound with a Raspberry Pi | BirdNET-Pi Project
Ever wanted to know exactly what bird is near you by only the sound but simultaneously have zero ideas about birds? Fear not, here is the solution for you! A fully fletched Bird Call AI System that runs completely on a Raspberry Pi Single ...
Accurate IoT Clock With ESP8266
Being punctual is important. Hence accurate time is required. Clocks tend to miss out when it comes to accuracy especially when they are set by the user. So, why not get accurate time from the internet and use tried and tested hardware to ...
The Hipster Coaster
We wanted to make a interactive display of the fun that can be had with DIY projects to take to Sydney Mini Maker Faire. We decided to do so by utilising the TinkerKit Braccio from Arduino.org, alongside some 3D Printing ingenuity, for an e...
Mini Desk Vacuum
Chances are if you are anything like me, being a maker is often an excuse to create as big of a mess as possible during the duration of a project. And after the project is finished? You are left with an enormous mess to clean up, taking awa...
Pico Baro V2
Introduction:
The inspiration for this project stems back to my childhood when I was curious to find out how the mechanical barometer worked.
Introduction:
The inspiration for this project stems back to my childhood when I was curious to find out how the mechanical barometer worked.
Creating our own Raspberry Pi 3 Case
We've got a whole bunch of Raspberry Pi 3 Cases here at Core Electronics. From the Official Enclosure that's perfect for most uses, right through to the gilded PiBow Coupe from Pimoroni. All of the cases we see have one or two impressive fe...
IoT Soundscape
I had been captivated by the sound levels of trains I could hear passing by Metford throughout the day/night. I wondered if a sound level sensor reporting data back over LoRa would help me understand when a train was noisy. I also like the ...
GraviTrack Enhancements - Lights and Sound
Introduction Searching for solar panels and related items on the Core Electronics website; I came across the Solarbotics GraviTrack Marble Machine Kit. I thought the kit would be a good educational tool for the grandkids. The kit was a hit...
IR Break-Beam Stopwatch
This project is a simple stopwatch with a little bit of a twist! It operates like a conventional stopwatch… you can start and stop it, you can record lap times and you can review the lap times once you hit stop. The twist is th...
Spirit In A Box Halloween Trick
Introduction
This project was born from the desire to craft a captivating and spine-tingling magic trick that would add an air of mystique to a Halloween and supernatural-themed party that ...
Ping Pong Launcher
I like to take on projects that give me an opportunity to learn new things. For this project, my two goals were to learn more about face detection algorithms and PID controllers but of course, there were so many more skills learned along th...
Days2Bin: Pico Powered Bin Reminder
Our recycle bin is collected fortnightly, but I can never remember which week, and the printed calendar changes every year! So I made a Raspberry Pi Pico W and GlowBit Matrix powered model wheelie bin which shows when the bins are due at a...
LoRa P2P Wireless Gate Alarm
Introduction
My front gate is a long way from the house at around 300m. I don’t want people wandering around my property without knowing about it. This project uses two Raspberry Pi P...
ESP32 IR-Triggered Camera with Home Assistant Integration
I love the ESP line-up. I started by messing around with the ESP8266 and I completely fell in love with it. The 8266 is all I ever wanted from a microcontroller: WIFI connectivity, a decent amount of GPIO, a deep-sleep mode for batter...
IoT Pet Feeder
The objective of this project was to create an Internet of Things (IoT) device that could give pet access to a food bowl when a text message command was sent from a remote location. I had never done an IoT project before, so I wanted to ke...
Raspberry Pi Pico Long Range Radio (LoRa) Weather and Air Quality Station - Full Dashboard (DataCake + TTN), Rain-Proof and Long Range
Have you ever wanted to make a Weatherproof Weather and Air Quality System that transmits its edge-collected data long-range through LoRa (up to a 10Km range) and then have that data automatically uploaded to the Internet to be gorgeously ...
Math Scroller
I was looking for something educational to 3D-Print for my child in Thingiverse and came across the concept of the Math Spinner. I found the models lacked a method of checking the answer so I wanted to automate it. The core design is inspir...
SOLARBOI
Since I was young, I've always loved to explore. Over the years, I've tinkered with RC cars and played with planes, which were always plenty of fun. But I always dreamed of going out further - out into the real world, far beyond the confine...
WhyzaGC - Feather ESP32 addon to the MightyOhm Gieger Counter
This project is about adding a wireless Adafruit Feather HUZZAH ESP8266 or ESP32 v2 with Adafruit Featherwing 128x64 OLED to interface with the self-assembled MightyOhm Geiger Kit.
Introduction
I am always on ...Introduction
I am always on ...
Vehicle GPS Logger and Speedometer
Purpose
To display time and speed to a driver while logging timestamped raw latitude, longitude and speed as returned by the GPS satellite network. This allows a driver to double-check th...
Roverling Mk.ⅠⅠ
Introduction
A few months back I created a basic mobile platform using parts from an old 3D printer. It was fun but not very practical. I designed Roverling Mark II so I could experi...
Makers love reviews as much as you do, please follow this link to review the products you have purchased.