Out of Stock
Sign up to get notified when it's available to order.
This guide will help you get started with a PiicoDev® Servo Driver module. We'll take a tour of the module and walk through some examples to drive common servos. Servo motors are integrated motors that contain their own power circuitr...
In this guide, we'll learn what a Servo is, when we might use one, how to choose a Servo, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A Positional Servo, such as the Feetech FS90 Micro Servo A Con...
This guide will teach you how to control any small and big servos with a Raspberry Pi 4 Model B (worth noting any Raspberry Pi Board with GPIO pins can be able to be used in this scenario. Servos are an immensely useful way to turn ele...
The :MOVE MINI allows you to turn your micro:bit into a simple robot! In this guide, we will give you some tips and tricks for assembling the :MOVE mini. This is a DIY assembly item and takes 30-60 minutes to fully assemble. There is a grea...
In this guide, we go over some common ways of adding motion to your project with actuators such as stepper motors, servos and linear actuators, to help you choose which one is most appropriate for your situation. The start of this guide c...
Servo motors are extremely useful in so many different applications; it’d be good to learn how to control them! Solenoid and DC motor control have been shown already; for the most part, they are both pretty straightforward (only powe...
This guide will teach you how to control up to 992 5V Servos through the GPIO pins on your Raspberry Pi! But more practically, without stacking multiple HATS (Hardware Attached on Top), this guide will teach exactly how to control sixt...
Hailing from Aleph Objects in Loveland, Colorado, the Lulzbot range of 3D printers are world renown for their quality, reliability and ease of use. The reason they're so popular? Apart from the gilded Lulzbot technical support (practically ...
Arduino Projects with Motion (Using Sparkfun RedBoard) Welcome to the Third Project Set from the Sparkfun Inventors Kit V4.0 Guide! In this tutorial, we will explore the operation of a Servo Motor and an UltraSonic Sensor in combination wi...
Pimironi Picade Pan-Tilt Hat lets you mount and control a pan-tilt module right on top of your Raspberry Pi palm-sized computer. Setting up a Pan and Tilt system has never been easier with absolutely no soldering required! Pe...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Mi...
In this guide we'll create a simple HTTP server using a Raspberry Pi Pico W. This server will be accessible from within a local WiFi network and can be used to read sensors and control hardware - in our case we'll drive an LED and read the...
The Slim Case for the Raspberry Pi Zero, Zero W and Zero WH provides protection for your Raspberry Pi without adding unnecessary bulk. Best of all it keeps everything sleek and tidy without hiding the board itself. The Slim Case was de...
Stepper Motors are a bit of a halfway mark between DC Motors and Servo motors, but they find a sweet spot that allows them to be perfect for certain applications. There are still a few main differences to be aware of when it comes to workin...
Introduction We’re going from zero to hero. Starting from nothing we’ll get a WiPy communicating with Adafruit IO, an IoT service out on the Internet. We’ll be able to send data from the device to the cloud and control th...
In this guide, we'll be learning about sensors that measure inertial movement, how they work, how to choose the right sensor type, and how to get the most out of their readings. Hardware mentioned in this guide: PiicoDev Accelerometer ...
Where do I start? If you’re new to programming Python is a great place to start! I’ve seen Python taught to primary school age children and I have used Python in a Machine Intelligence course at university. It’s no wonder...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto yo...
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - the transition from a consumer buying goods to eventually having a major part in their creation. The Maker Revolution places strong emphasis...
This guide will demonstrate exactly how to control Standard Stepper Motors and DC Motors with a Raspberry Pi Single-Board Computer. To do this as seamlessly as possible we will utilise a HAT. HAT stands for Hardware Attached on Top. HAT bo...
"Yes, I would recommend this a friend." That's the verdict of 90% of people who pick up the Rule your Room Kit from littleBits. We love it so much, we're most definitely recommending it to you and your family. But you don't need to take ...
In this guide, we'll learn what a Rotary Encoder is, when and why we might use a Rotary Encoder, and how to use a Rotary Encoder with a Raspberry Pi Pico. To follow along all you'll need is: A Rotary Encoder - we recommend using our br...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto y...
Welcome to the Raspberry Pi Pico Workshop, where you will learn everything you need to know to hit the ground running and start making your own projects with the Raspberry Pi Pico and MicroPython. This workshop is designed for complete beg...
Introduction Let's play tones and melodies on a PiicoDev® Buzzer Module with a Micro:bit. This guide will cover connecting the hardware, running an example to make sure everything works and playing simple melodies. Of course, the Micr...
Introduction Let's play tones and melodies on a PiicoDev® Buzzer Module with a Raspberry Pi Pico. This guide will cover connecting the hardware, running an example to make sure everything works, and playing simple melodies. To follow ...
Introduction Let's play tones and melodies on a PiicoDev® Buzzer Module with a Raspberry Pi. This guide will cover connecting the hardware, running an example to make sure everything works, and playing simple melodies. To follow along...
The aptly named Ultimate Kit 2.0 is the final kit in the line-up of educational robots from Makeblock. With over 160 independent mechanical parts and modules, the Ultimate Kit 2.0 answers the call for almost limitless creative freedom. Matc...
Say you want to build a sun-tracking solar panel. You could add a tiny computer, like an Arduino, to control it. That might be all you need. But what if you need to connect to it to control it from somewhere else? Connecting it into your ho...
A digital multimeter (DMM) is one of the most common tools on a Maker's bench. We use DMMs to take electrical measurements in a fast and relatively accurate way. The reason we call it a multimeter is because they can take multiple types mea...
It’s always a fun day when you get hands-on with a device as cool as the 8Bitdo Zero Bluetooth gamepad. 8Bitdo are known are for their re-creations of classic gaming controllers such as the SFC30 and NES30 which bring the magic of NES...
Note that the digital artifacts on the screenare from the camera used to capture and not the screen itself How many great artworks or photos have you seen that consist of just lines of characters; words and numbers? Very few. It’s ...
We're going to compare each of the Arduino Boards available to Maker's and Electronics Enthusiats. We'll discuss the features of each board, provide an informative pinout diagram with tonnes of detail, and toward the end of the article, pro...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Mi...
First of all, why subject your Raspberry Pi to this level of stress? In the case of Raspberry Pi 4, the A72 CPU is so powerful that it can overheat if it doesn't have enough cooling. This results with the CPU being governed (slowed do...
Welcome to the Circuit Playground Express Workshop! This workshop is geared toward educators and coding beginners, who want to get started programming with this easy to use platform. We will go over everything you need to know to get you st...
Introduction This guide covers the configuration steps required to use the Makerverse Supercap Real Time Clock module as a backup RTC on a Raspberry Pi. This is required for remote applications when Internet access is impractical and accur...
Welcome to Counting with Computer 101. Have you ever looked at a colour on a computer and seen something like this #28FE9A? Or perhaps the T-shirt stating ‘There are 10 types of people in this world, those who understand binary, and t...
The Adafruit Circuit Playground Express comes packed with sensors, and for this tutorial, we are going to learn to use the onboard thermometer (technically a thermistor)! We will take temperature readings with the thermometer and print out ...
Welcome to the next step of understanding in your programming escapades with Python. This guide will introduce an overview of all keywords within Python, provide an understanding of what exactly a keyword is and how to make simple codes wit...
If there’s an odd one in the Pycom family of microprocessor boards it’s this one, the SiPy. There’s nothing wrong with it, it’s just that its sister board the LoPy4 has the same capabilities as SiPy, plus a LoRa ...
Welcome to 'Zero to Maker,' a workshop that will walk through and introduce a ton of tools and skills to help Makers of all skill levels! In this series, Jaryd and Liam will be completing projects as a part of the 2024 Fab Academy and...
Let's unlock Biometric Control on our Raspberry Pi Single Board Computers! Biometric Technology uses unique physical or behavioral attributes that are individual to each person and not (easily) replicable. Extraordinarily everyone on Earth...
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS ...
What’s even better than the world’s most popular microcomputer sitting on your desk? When it’s sitting there in a case which protects it, makes it easier to use, and gives your desk some style. If you buy a Raspberry Pi i...
LulzBot have released the Aerostruder for both Mini and Taz Printers now (Mid 2018). It features a Titan Aero Extruder from E3D, which makes it capable of printing in flexible filament and rigid filament, depending on the situation! It's an...
Want to setup a wireless XBee network between some Arduinos and your PC? We're going to show you how. We will be using Series 1 XBee modules alongside some XBee Explorer USB modules from Sparkfun to set up our own Personal Area Network (PAN...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. One of the simplest sensors in an...
There are a ton of electrical wire connectors, too many to elaborate on in a single guide, however there are a couple of connectors that as a maker you will come across. Often when starting your way into the electronics world all you need ...
Time to create a Little Red Advertisement Devouring Monster. This will be a self-hosted, network-wide, ad-blocking system running on a Raspberry Pi Single Board Computer. It will also stop access to malware sites and phishing websites. Fur...
So what does it mean to run headless?A computer setup without a monitor is said to be running headless. You might want to do this if you're installing your Pi into some project, or want to keep power-usage and cost minimal. This kind of se...
Who should follow this tutorial? If this is your first experience with Raspberry Pi, and you're using a starter kit for a Raspberry Pi Zero W, then this tutorial is for you. We'll plug everything into where it needs to be, install an ...
Have you heard about the Circuit Playground? It's the new all-in-one electronics platform from Adafruit. It was created to bring all the fun features of electronics and physical computing to makers, but It's dead-simple to use, solde...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. The TMP36 is a low cost, eas...
It is time for a high-quality, complete package, 1920x1200 (HD) display set up with a Raspberry Pi Single-Board Computer. In regards to touch screens with Raspberry Pi have looked at Tiny GPIO HAT LCD displays, medium-sized AMOLED maker di...
This Weather Station with Arduino was designed for the South Australia Catholic Education STEM Weather Station Challenge. We were lucky enough to be asked to build one of the basic kits provided to schools across South Australia for entry i...
Adafruit has done it again with the new and improved Circuit Playground Express. This new version of the Circuit Playground is packed with even more sensors, and capacitive touch ready connection pads. This is a great board for makers ...
Core Electronics is the official supplier for Arduino products Australia wide. We stock components from both Arduino.cc (Genuino) and Arduino.org (Arduino). Sourcing our products directly from Arduino ensures you are supporting the team beh...
The new Gizmos and Gadgets revision 2.0 from littleBits is here and we've decided to review the kit for any budding inventors (or inventor's parents) out there. The v1.0 kit was impressive enough, we were interested to see what littleBits c...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. One of the most common sensors in...
Introduction This guide covers the basic use of the Makerverse Supercap Real Time clock on the Raspberry Pi Pico using our RV3028 MicroPython module. The MicroPython module implements some commonly used features of the RV3028 RTC but is no...
Imagine being a builder without a hammer, or a car without a brake, this is kind of useful, but nowhere near as useful as it could be. This is like being a maker/DIY’er/enthusiast without being able to solder. Sure you can breadboard ...
What level of support do I get with my Lulzbot products? For all technical support enquiries for anything Lulzbot related, Aleph Objects have support covered all-day long. Email [email protected] and the team over at AO will get back to ...
The Feather boards are the brains of your project, we took a closer look at the different models in our Birds of Feather article, check that out first (especially if you have no idea what the difference is between a feather and a wing). You...
What a glorious time we live in, where, as technology continues to evolve, so too does the ability to learn more about it and get hands on with concepts that would otherwise be out of reach, especially for young minds. Today, we’re go...
Project Set 2 – Sound Welcome to the second Project Set from the Sparkfun Inventors Kit V4.0 Guide! In our last Project Set, we explored the basics of the Arduino IDE, some electrical and electronic concepts and looked at vario...
This guide will teach you exactly how to use a Raspberry Pi Single Board Computer to independently control 4 relays. A Relay is an electrically operated switch. This is all possible thanks to the PiRelay V2 HAT from SB Components. These re...
Arduino Projects with an LCD (Using Sparkfun RedBoard) Welcome to Project Set 4 in the Sparkfun Inventors Kit Guide! In this tutorial, we will look into using Liquid Crystal Displays (LCD's) to print data. This ability allows us to remotel...
Lulzbot is constantly building upon their printer's design, incorporating the best modifications and add-ons from the community into their newer models. In May 2016, their newest addition to the TAZ line of printers, the TAZ 6 wa...
Once you setup your printer and finish printing your first rocktopus, you will inevitably want to move onto more ambitious prints right away. It’s understandable, all the possibilities all at once, I get it. We are going to step you ...
Recently, we've talked a lot about Slicing software, settings, materials and the like. It's time to take a deeper dive into the actual design of model files. We've got a basics guide for Computer Aided Design available here. We're going to ...
Once you receive and unbox your Lulzbot machine you might be so eager to print things, you skip a few steps in the setup process and all of a sudden you are having all sorts of difficulties that you can’t understand. It happens, what ...
PLA is Poly-Lactic Acid filament, and it's usually the go-to choice for people looking to print larger models or for longer periods of time. The important properties of the material dictate the reasons for using it; it doesn't warp at all a...
Out of the box, a LulzBot 3D Printer comes tuned to perform exactly as you need it to. But over time we flash new firmwares, take our printers cross country, swap tool heads, perform cold pulls and a whole swathe of other things that could ...
3D Printing is one of the ways we can turn virtual 3-dimensional models into real world objects. It is an Additive manufacturing (AM) process, building models layer by layer. AM is the opposite of subtractive manufacturing which takes a blo...
OctoPrint Integration is one of my favourite new features in Cura 2.6+: LulzBot Edition. In short, this integration means that you can print and control your 3D Printer via it's OctoPrint server. All from within your slicer window on your P...
Welcome to our beginners tutorial on analog electronics. Living in the digital age that we do, it’s easy to disregard the world of discrete analog components, however these concepts form the basis for everything from your mobile phon...
If you've picked yourself up a 3D printer, you've no doubt printed yourself a heap of models from Thingiverse by now. It's great fun and the best way to learn how to control the options you have available through Cura; scaling, rotating and...
If you’ve ever built a robot with wheels, or any motorised parts really, you’ll have come across the issue of needing to drive it from your microcontroller. Because a standard chip is only able to output a small amount of curren...
There are a wide range of filaments available in FDM 3D printing; it’s easy to get lost in all the abbreviations, acronyms, and temperatures. We’ve decided to bring together the most relevant information when selecting fila...
Thanks to huge advancements in technology over the last decade, the maker community that we know and love has thrived. It’s now easier than ever before to get started with programming and tinkering due to the innovation from brands su...
Espressif is a constantly ground-breaking company that produces lots of really cool development modules which includes the ESP32. ESP32 Boards, ESP32 Dev-Kits, and ESP32 Modules (the part that gets soldered to the Board/PCB) are all about ...
Welcome to the C Programming Workshop for Makers! Here you'll be able to follow along with our series of easily digestible videos that cover everything you'll need to know to on your way with C programming and start making awesome projects....
Hey guys, if you’re looking to get the creativity and fun of Makey Makey into classrooms or workshops, then you’re in the right place! Makey Makey is an incredible tool for educators to get kids thinking about how they can use t...
Hello, and welcome to our tutorial where we’ll be looking at two different types of soldering irons and which one is going to be best for your workshop. We’ll be specifically looking at soldering irons, not how to solder, so for...
In case you haven’t noticed, when dealing with electronics, you’ll be picking lots of small things up, and it only gets harder when dealing with tiny SMD components. But whatever you’re working on, be it a breadboard proto...
Welcome to the Raspberry Pi Workshop for Beginners! Here you'll be able to follow along with our series of bite-sized videos that cover everything you'll need to know to get started with your Raspberry Pi, and start making awesome project...
IntroductionIn this guide, we'll get a Raspberry Pi Pico W connected to the internet using WiFi. To demonstrate the connection we can query a webpage, or get the current time from a time service. To follow along, all you'll need is: A R...
In the dynamic and ever-evolving world of open source technology, the PiicoDev community really stands out to me as a curious and humble one. While the project's main repositories on GitHub serve as the heart of our collective endeavor, it...
Let us set our codes free into the world wide web and design codes which access real world data! This real-world data will represent the current reality of the world around us. Application Programming Interface requests is the method that a...
IntroductionIn this guide, we'll get a Raspberry Pi Pico W to send and receive data to the cloud using the MQTT protocol. To follow along, all you'll need is: A Raspberry Pi Pico W Understand how to connect the Pico W to WiFi Underst...
What is Node-RED? Node-RED is a tool originally created by IBM for flow-based programming, and has built-in support for the Raspberry Pi and it's GPIO capabilities. It runs on top of Node.js, and can be accessed with just a web browse...
The Infinity Mirror Kit is a desk-top display that creates a dazzling optical illusion - a tunnel of light that tears through space! Note: This tutorial is for the Infinity Kit V1. We updated have updated to the Infinity Kit V2 as of ...
So you have just received your OctoPi kit and you are looking to get it up and running. All you need to do is grab out all the parts you received and around 20 minutes of time. To connect your OctoPi to the network you need to decide what ...
There is a whole range of Sub-4 Inch Displays that attach directly to the GPIO pins of Raspberry Pi Palm-Sized Computers. Many of them are touch devices and increase the usability of your Raspberry Pi whilst making almost no size sacrifices...
What is MQTT? MQTT (Message Queue Telemetry Transport) is a simple and ‘lightweight’ way for internet-connected devices to send each other messages. This is important for home-automation because devices need to send messag...
A radio transceiver is a device that can both transmit and receive radio signals, making it the perfect tool for communication on the go and remote projects! The PiicoDev Transceiver™ is a 915MHz radio that can send short messages up...
Welcome to the 3D Printing Workshop! I'm Aidan from Core Electronics and in this workshop we are going to take a hands-on journey into the exciting technology that is 3D printing. I have personally spent the past 12 months immersing mysel...
Remote control of your 3D printer is a particularly appealing concept, especially if you've been forced into printing via USB in the past. Using your new 3D printer should be as simple as plugging it in, uploading some G-Code and pressing '...
To fully equip ourselves on our Python odyssey we will take a leap into Operators and their Precedence. Python is undoubtedly a Homeric programming language, epic in its possible applications and vast in its potentials. Operators ...
The Raspberry Pi has revolutionized the world of single-board computers, offering a platform for learners, hobbyists, and professionals to explore, create, and innovate. From its inception, the Raspberry Pi series has been a beacon of techn...
Ever wanted a pocket computer with a Full HD screen (1080x1920)? Love tiny GPIO screens like this 3.5 Inch from Waveshare but want one that is a little bigger and higher resolution so that it is easier to read? Or want a really premi...
In August of 2014 Shanghai-based chip manufacturer, Espressif, released a ultra-cheap Serial to Wi-Fi chip called the ESP-01. At the heart of the ESP01 was an ESP8266 chip broken out into the 8 pins needed to program it via a microcontrolle...
Feel restricted by your connectivity? Want to send data from a remote node 10km away from civilization? Or ~3km when you are in a built-up civilization. Feel the urge for Liberation? Then I have the solution for you! Using only hardware bu...
Not quite sure how to get started with your Pimoroni Blinkt module? Let's set one up and have a play around! We'll guide you through the installation, open up some examples and try our hand at writing a simple program. You'll need: A Ra...
If you’ve been around electronics for a while you’ll have noticed the trend of single board microcomputers targeted at hobbyists through to industrial projects, the most popular platform being the Raspberry Pi. Now the Raspberry...
Welcome to the best article on setting up an OpenMediaVault-based NAS on a Raspberry Pi Single Board Computer! This guide is the fastest and best way to go about it. Raspberry Pi single-board computers are purpose-built to run 24/7, with a...
Geophones are devices that generate electric signals proportional to the particle velocity in a sound/compression wave. More simply a Geophone is a super low frequency microphone for the ground. Geophones are used around the world to measu...
Fused filament fabrication and transparent prints! No, surely you mean SLA prints. And true you can get excellent transparent prints effectively using SLA however consumer-grade fused filament fabrication can be mistaken for glass when corr...
In case you haven’t noticed, Internet of Things is the phrase on everyone’s lips right now; why make a device, when you can make an IoT device? And the good folks at Particle.io have made it easier than ever to create your own...
warning: Pycom has updated their libraries and the code listed below may not work. If you discover this and find a fix, please post it on our forum and we'll send you a $25 store credit along with a huge thank you. Go to Forum Thread. ...
We’re in a golden age of connectivity, the internet we know today has given us the tools to connect anything to anything, and now with the platform brought to us by Particle, DIYers everywhere can connect the creations up to this va...
In the attempt to give the most comprehensive and truly easy to understand reference pages for the programming language of Python it is only natural to talk about built-in functions. A function in Python is a block of code which only runs w...
In this tutorial, we will learn how to code for the Onion Omega2 on our PC, and then wirelessly upload our code using the ATOM text editor. The ATOM text editor is a powerful and easy to use text editor developed by the team at Github...
After the release of the Raspberry Pi 4 Model B 1 GB and 2GB and 4GB generations there was a design revision. Now if you have any other Raspberry Pi board in your hand the impact of this design revision will not affect you. If you happen to...
PiicoDev is the open-source and best-documented platform specifically designed with rapid prototyping and maker education in mind. As fellow community educators, we have infused PiicoDev with ideas to ensure that every home project, school...
Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what you can do with it if you take a look under the hood. One of the most popular experiments to do with your Raspber...
Before we dive into the FIDO Certified Key-ID Security Key and how it's used, let's get a handle on what authentication online means at the moment. Authentication is simply the process of identifying a user based on a set of unique factors...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. Connecting your Pycom Lopy4 or an...
Progressing further into the epic programming language of Python the instinctive next step should be user defined functions. Now as a quick refresher, a function in Python is a block of code which only runs when it is called. It is organise...
While the Raspberry Pi Compute Module 4s (CM4s) share a lot with the regular Pi 4 Model B, getting started with the flashing process can be quite different depending on which model you pick! This article aims to demystify that, so without f...
The Pysense expansion board from Pycom has many sensors. In Pycom Pytrack Getting Started, I showed how with some Processing code we can see the real-time position of the board in 3D. That project works with the Pysense too. How about we sh...
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. warning: this is a "nano" gateway...
Of the many great objects you can create using any 3D printer lithophanes are definitely up there. Traditionally lithophanes were an etched or moulded artwork created on a very thin translucent porcelain that can been seen clearly only...
Hola on your next viaje in Python. Python is an absolutely asombroso programming language and this is the next step on the escalera of understanding. This guide will focus on the | pass |, | continue | and | break | keywords. The...
Now I'm not talking about a delivery service - I'm talking about an Uninterruptable Power Supply for your Raspberry Pi 4. So if your Raspberry Pi project needs to be powered all the time relying solely on the mains power system may leave y...
If your 3D printer is an Ultimaker S5 then your prints will almost always come out looking brilliant. Although achieving desirable 3D printed components can sometimes require troubleshooting to resolve print errors. These errors often can ...
Love your Raspberry Pi but wish it had even more connectivity akin to your mobile phone. Then the Waveshare 4G HAT is the solution for you! HAT simply means Hardware attached On Top. With this installed on your Raspberry Pi Single Board Co...
So, you have set up your shiny new resin 3D printer and now want to produce beautiful models. Well, this tutorial will tell you exactly what to do from filling the tank, starting a print via USB then the removal, cleaning, and final UV ligh...
The PiicoDev® Air Quality Sensor is based on an ENS160 multi-gas sensor that detects Volatile Organic Compounds (VOCs). These measurements are run through some algorithms to produce standardised outputs like Air Quality Index (AQI...
Filament grinding is very unlikely to occur if your running an Ultimaker S5 3D Printer with Ultimaker materials or 3rd party supported materials. Filament grinding occurs when the knurled feeder gear slips against the filament instead of sm...
It has finally happened, they figured it out! The new frontier of Colour Electronic Paper is here and I'm very impressed. People have been demanding this ever since the first E-Paper readers hit the market in the noughties. That black and ...
The Infinity Mirror Kit V2 is a desktop display that creates a dazzling optical illusion - a tunnel of light that tears through space! The Infinity Mirror Kit V2 entered production in October 2018, and now ships with an Adaf...
Welcome to the Python Workshop, where you will learn everything you need to hit the ground running with the worlds most popular programming language Python. My name is Tim and am a passionate maker and cherish free exchange of knowledge. I ...
A popular question that we get all the time is ‘How do I choose a speaker or amplifier to go with my project?’. It’s a good question, and if you’re not familiar with the terminology, it can seem a bit daunting to kno...
Introduction So now everything is available in this day and age, and all those childhood dreams can now come true as parts, technology and software has come a long way. I had recently taken up the hobby, RC planes. Eventually I learnt ho...
This project incorporates two Arduino boards, in a Master/Slave setup. The master is one with an accelerometer (ADLX345) and the slave has a Servo attached (SG90). When tilting the accelerometer, the master Arduino tells the Slave Arduino t...
My son really wanted one of the mini NES when they were released, however he missed out. I already knew that you could use a raspberry pi as an arcade emulator, so I thought why not build him one.
I grew up playing old arcade machi...
I grew up playing old arcade machi...
I like to take on projects that give me an opportunity to learn new things. For this project, my two goals were to learn more about face detection algorithms and PID controllers but of course, there were so many more skills learned along th...
Chances are if you are anything like me, being a maker is often an excuse to create as big of a mess as possible during the duration of a project. And after the project is finished? You are left with an enormous mess to clean up, taking awa...
This mini cube is made up of six 4x4 WS2812B panels giving a total of 96 individually addressable RGB LEDs. Buried inside the cube is an ATTiny85 microcontroller powered by a 120mAh Lithium-Ion battery. It also contains a mercury switch and...
I really love the reliability of my Fuji wireless mono laser printer. Best printer I've ever owned. However, it was released without Google Cloud Print. This required constant driver installation on new devices and the inconvenience of not ...
An array of individual cosmic ray detectors distributed across a landscape to display how cosmic rays arrive as showers of muons. It's all powered by a Raspberry Pi Zero!This project deployed 16 individual cosmic ray detectors on the banks ...
Ever wanted to record a video and be included in it? My children did. One does parkour, and the other loves to dance, both want to perfect their art by watching their moves during practice. They asked their inventor/tinkerer dad, "can you ...
I bought a Pi zero w from Core Electronics for a friend, also bought the official case too but thought I'd fit the Pi into something he can show off! I used an old hand held game case I had laying around, I had to remove the original circu...
The inspiration for this project stems back to my childhood when I was curious to find out how the mechanical barometer worked.
The inspiration for this project stems back to my childhood when I was curious to find out how the mechanical barometer worked.
I read somewhere about UNIX Epoch time and thought wouldn't it be neat to have a clock that showed time in this format? This project developed from that idea. I had a unused GPS module with serial output so I thought it would also be cool ...
This project has been created to be used as an exemplar for Year 7 Technology students to demonstrate some of the features and potential of making with a micro:bit. This device is a teacher tool or game accompaniment device that random...
We wanted to make a interactive display of the fun that can be had with DIY projects to take to Sydney Mini Maker Faire. We decided to do so by utilising the TinkerKit Braccio from Arduino.org, alongside some 3D Printing ingenuity, for an e...
These days we can do just about anything on our phone, we can control so many aspects of our lives using the technology in our pocket, but the most mundane aspects of our lives; opening the garage door, blindly reaching for the light switch...
I used an Arduino and a US-100 ultrasonic sensor to make an extremely low-cost tide gauge. This project measures the tide by sensing the distance to water using a US-100 ultrasonic sensor. The device has a 3D printed base&nb...
This project started life as an alarm clock for my son made to look like the time circuit from the Back to the Future movies. The display can show the time in various formats, including the one from the movies of course. It's configurable v...
The Raspberry Pi Zero W is a tiny, yet powerful little device. Coupled with a Pimoroni Speaker pHat, it can be easily turned into a portable Airplay speaker which allows you to stream your music anywhere you want.Parts you'll need: Raspb...
How-to guides are very useful, but while “do this, then do that” is great to reproduce exactly what is in the guide, it’s less helpful if you want or need to modify the project. This is especially true with technology proj...
This one is for the Stargate fans out there. A realistic, 3D printed, light-up Zero Point Module! I found a model on Thingiverse for a ZPM - It had good detail but - I took issue with the visible seam, and to change the colors of any cryst...
I was interested in creating a RPi Cluster to learn about how they work. After getting the clusterhat and Pi Zero Ws I set about creating the images for 5 sd cards. This seemed a waste so I scrapped that idea and setup the image for one sd ...
We made a Pi Zero W retro-games console! The nostalgia is making me dizzy! If you'd like to build your own, we've put together a couple of wishlists to make things easier: For the Pi Zero W build, like in this project, check out the PiG...
Who says you can't have it all? Good looks and a great sound! My name is 'Holman" and I'm a Bluetooth speaker in the form of mans best friend - a dog of course! Why is my name Holman? Well, that's the name of the manufacturer of the PVC pi...
Recently I finished my first Particle Photon project. It’s basically a temperature, humidity, and barometric pressure monitor all in one! I’m not a programmer, but I know enough to tweak code when necessary. I have, on...
Tunnels are a critical part of road infrastructure and they feature some pretty cool tech. This Smart Tunnel project demonstrates some of the technology involved and how some real-world problems might be solved. Features RFID Trip...
For $50 and some dedication a retro gaming console can be yours and with HDMI you can play it with any modern TV or monitor. Instead of using bulky and space taking cartridges and discs it's all on the console. For this build, we're going ...
I’ve had a Current Cost Power Monitor for a number of years which worked well until we put solar on the roof. The Current Cost can’t determine which direction the power is flowing and so power generation and con...
I’ve had a Current Cost Power Monitor for a number of years which worked well until we put solar on the roof. The Current Cost can’t determine which direction the power is flowing and so power generation and con...
I am an amateur musician, coder, and electronics maker. When I found out that the Novation Launchpad (mine is a mini MK3) can be programmed, I was excited about creating unique music. The idea is to use the Launchpad to play a game and use ...
A smaller version of our amazing Infinity-Mirror Table - the Desktop Infinity Mirror compresses all the colourful goodness into a picture frame-sized display. The entire design is made from laser-cut acrylic that we cut in-house. Check out ...
The idea was to leverage the light transmitting properties of clear acrylic sheeting and pass LED light through it; interfering the transmission using laser cut edges which would cause the light to highlight the lines thereby creating a pai...
Hi all. Thought I'd share with you my modded Spirit Halloween proton pack. It's about 80% scale, which is plenty big enough for my 7-year-old son, and still looks decently sized on adults. As soon as I learned of this pack, 5-year-old me ju...
I strapped a Raspberry Pi Pico W to my garage door motor and now I can control my garage door from my phone! The Pico W hosts a simple webpage on my local network with three control buttons - one for Up, Stop and Down. Pressing one of...
My first arcade cabinet. Built from scratch using mdf panels, a donated monitor and speakers. Powered by f="/catalog/product/view/sku/CE05436">Raspberry Pi 3 running the free image "RetroPie". I have put on ab...
My first arcade cabinet. Built from scratch using mdf panels, a donated monitor and speakers. Powered by f="/catalog/product/view/sku/CE05436">Raspberry Pi 3 running the free image "RetroPie". I have put on ab...
I wanted to build a weather station. After some googling I found a great ‘how to’ guide using a raspberry pi.
I was also interested in learning Python, so I decided to dive right in...
I wanted to build a weather station. After some googling I found a great ‘how to’ guide using a raspberry pi.
I was also interested in learning Python, so I decided to dive right in...
This project started due to the smoke haze that enveloped our area during the 2019 and 2020 bushfires. I wanted something to check the air quality of my home and maybe find areas where it needed better sealing. In addition, the BMP280 senso...
I want to make a portable music box that my 2 year old kid can operate intuitively on her own. So, Spotify or any other on-demand music platform with tablets and Bluetooth speakers are out of the question. Remember the good old days of putt...
I was down at a local game shop recently and noticed their range of chess boards and decided to try my hand at a simple little project. I'm a big fan of Doctor Who, Chess and 3D Printing. So I decided to combine them all together into a fun...
The aim of this project was to use the sun to charge some batteries with 1W and 2W Seeed solar panels. The DFRobot Solar LiPo Charger and a Sunflower Solar Power Manager were purchased. Initially, this was unsuccessful because I did no...
As part of a larger home automation project, I wanted the ability to control some mains power outlets remotely. To achieve this, I interfaced the transmitter from an inexpensive 433MHz mains remote control kit with a raspberry pi zero w (vi...
Presenting the KiPad - a custom macro keypad for the popular open-source PCB design software KiCad. KiCad is awesome! But I've found that during PCB layout, my right hand is constantly moving back-and-forth between the keyboard and mouse -...
This project uses an ESP8266-01 WiFi module to send an alert to my phone if the fridge door is left open or ajar.
After ordering a few of the ESP8266 board variations I found myself with an ESP8266-01 variant which wasn't very usefu...
After ordering a few of the ESP8266 board variations I found myself with an ESP8266-01 variant which wasn't very usefu...
Our local council picks up recycling bins one week and green waste the following week. Sometimes people forget which bins go out each week and perhaps they mistakenly put the wrong bins out. Not that that has ever happened to me of course! ...
This is an Arduino project using and ethernet shield for remote control of a set of relays. The IPControl module was meant to be a simple web accessible device controller. It sort of grew! A little out of hand as you will see...
I love the ESP line-up. I started by messing around with the ESP8266 and I completely fell in love with it. The 8266 is all I ever wanted from a microcontroller: WIFI connectivity, a decent amount of GPIO, a deep-sleep mode for batter...
Introduction Searching for solar panels and related items on the Core Electronics website; I came across the Solarbotics GraviTrack Marble Machine Kit. I thought the kit would be a good educational tool for the grandkids. The kit was a hit...
This project is about adding a wireless Adafruit Feather HUZZAH ESP8266 or ESP32 v2 with Adafruit Featherwing 128x64 OLED to interface with the self-assembled MightyOhm Geiger Kit.
The UNITRAC (UNIversal TRACtion system) is a simple 3D printable conversion for the Black Gladiator-Tracked chassis, It’s designed to transform the large wheelbase platform into a self-contained propulsion system that has all the torq...
Do you get nightmares of losing your YouTube Subscribers? If you do, you are not the only one. Luckily I have made this "YouTube Desktop Notifier" to keep me up-to-date with my channels Subscriber and View Counts. This very simple DIY ...
Our recycle bin is collected fortnightly, but I can never remember which week, and the printed calendar changes every year! So I made a Raspberry Pi Pico W and GlowBit Matrix powered model wheelie bin which shows when the bins are due at a...
Being punctual is important. Hence accurate time is required. Clocks tend to miss out when it comes to accuracy especially when they are set by the user. So, why not get accurate time from the internet and use tried and tested hardware to ...
Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosure, I'm just about ready to turn on some serious 3D printing work. But before I dive into that endless pool of fun, it's a good time to take ...
The driver behind this project is to allow the remote control of some of the equipment in my shed. I have a CNC router/laser cutter that uses my compressor and dust extractor whilst it is running, and well whats the point in having a comput...
If you haven't already seen it, check out part 1 of this project. it has all the background info in it. And if you haven't got one yet, get yourself a particle photon, they are great. This part of the project was hooking the particle photon...
We've built a mass SD card writer using a Raspberry Pi 3 Model B, some USB hubs and SD card readers. This beast has enough ports to write 49 SD cards at once! At Core Electronics, sometimes logistics hang-ups mean that suppliers cannot mee...
Introducing to you today, the Quadbeest, the next evolutionary step in the Strandbeest genealogy. It seemed to be about time for Strandbeests to evolve to take over the air, so I made it happen. Able to be controlled over a kilometre in the...
The Raspberry Pi Microscope was put together to help with soldering PCBs that have small surface mount components. Its main function is to verify the quality of solder joints and ensure there aren’t any short circuits. With the addition of...
YAM (or YetAnotherMonitor) I keep more than 20 enclosures of Australian native lizards and turtles and I want to make sure they are all in an appropriate environment. To that end, I built a microcontroller-based system to monitor the tempe...
If you have chickens and find you're not always available to close the gate at night or check the water levels each day, then why not use an ESP8266 to automate your chicken door and receive alerts door status and low water level, as well a...
I use a Raspberry Pi running EmonCms for collecting sensor data and controlling devices around the home but several things have been on my To-Do list to enhance its functionality. A Shutdown/Power Down/Startup circuit. Proportional fan...
[Update – Until there is correct compatibility of NPM with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Micro-...
It is real and here it is! Including everything you need to make one a Luma 1 for yourself! So allow me to introduce you properly to the Luminator Mark 1. I'm talking all the ins and outs of this inside-out neo disco ball so you can ...
This project is to build a super cheap wireless adapter based on Raspberry Pi Zero and ENC28J60 ethernet module for Xbox 360I have two Xbox 360 consoles and today I want to connect them together but I only have one OEM wireless adapter. It ...
This project started because I wanted to know the signal strength of the Wifi in various places around my house. I had set up a Pi Zero as a simple watering system controller. It would switch a solenoid on and off based on a 7 day schedule;...
This project is to modify a Dell multimedia keyboard into a Raspberry Pi Zero dedicated keyboard with external powered USB hub. You can find this article in my blog http://sizeofinfinity.blogspot.com.au/2017/06/modify-dell-multimedia-keyboa...
I made a Raspberry Pi camera that captures GIF files and optionally tweets them over WiFi! It's built around a Raspberry Pi Zero W and a Pi Camera module. The camera connects to a pre-programmed WiFi network to tweet the gifs, but...
This project is a raspberry pi powered photo both. It uses a raspberry pi zero and the raspberry pi camera. All the code has been uploaded to GitHub for you. It has a ten-second timer, from when you press the button, and then it takes ...
I had been captivated by the sound levels of trains I could hear passing by Metford throughout the day/night. I wondered if a sound level sensor reporting data back over LoRa would help me understand when a train was noisy. I also like the ...
Makers love reviews as much as you do, please follow this link to review the products you have purchased.