Search results for: 'LM7912 -12V 1A Regulator'
- Pololu 12V, 1A Step-Down Voltage Regulator D24V10F12SKU: POLOLU-2834 Brand: PololuThe compact (0.5" × 0.7") D24V10F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while...
- 5V, 1A Step-Up/Step-Down Voltage Regulator S13V10F5SKU: POLOLU-4083 Brand: PololuThis powerful synchronous switching step-up/step-down regulator efficiently produces 5 V from input voltages between 2.8 V and 22 V. Its ability to...
- Pololu 9V, 1A Step-Down Voltage Regulator D24V10F9SKU: POLOLU-2833 Brand: PololuThe compact (0.5" × 0.7") D24V10F9 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V while...
- Pololu 6V, 1A Step-Down Voltage Regulator D24V10F6SKU: POLOLU-2832 Brand: PololuThe compact (0.5" × 0.7") D24V10F6 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 6 V while...
- Pololu 3.3V, 1A Step-Down Voltage Regulator D24V10F3SKU: POLOLU-2830 Brand: PololuThe compact (0.5" × 0.7") D24V10F3 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 3.3 V while...
- Pololu 5V, 1A Step-Down Voltage Regulator D24V10F5SKU: POLOLU-2831 Brand: PololuThe compact (0.5″ × 0.7″) D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 1 A.
- 12V DC 1A Fixed 2.1mm Appliance Plugpack12V DC Switchmode Plugpack Supplied with a fixed center positive 2.1mm DC jack.
- H-Bridge Motor Driver 1ASKU: COM-00315 Brand: SparkfunFaster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just that. Capable of driving high voltage motors using TTL 5V logic levels, the SN754410 can drive 4.5V up to 36V at 1A continuous output current! Please see datasheet for more information. This is a pin to pin compatible replacement for the L293D.
- 802.3af PoE Output Data & Power Splitter - 12V 1ASKU: ADA3238 Brand: AdafruitPower over Ethernet (PoE) splitters can make your project wiring a breeze - and best of all they work to connect any 802.3af-capable router to any Ethernet device...
- 1A Motor Shield For ArduinoSKU: DRI0001 Brand: DFRobotThis Motor shield for Arduino uses L293 chip which allow to drive two 7-12V DC motors with maximum 1A current. This shield can be directly mount onto standard Arduino Duemilanove and Arduino Mega.
- Monocrystalline Solar Panel (5V 1A)SKU: FIT0601 Brand: DFRobotThis is a high-performance, lightweight, portable monocrystalline silicon solar panel in a PET package, with an integrated voltage regulator output of 5V, with working...
- Electric Cooler Module (5V 1A)SKU: FIT0826 Brand: DFRobotStill worried that your CPU is running too hot? Take a look here! This kind of semiconductor refrigeration module is a simple application of the Peltier Thermoelectric...
- Diode Rectifier - 1A 50VSKU: COM-08589 Brand: SparkfunThis is a simple, very common rectifier diode. Often used for reverse voltage protection, the 1N4001 is a staple for many power, DC to DC step up, and breadboard projects. 1N4001 is rated for up to 1A/50V.
- Diode Rectifier - 1A, 400V (1N4004)SKU: COM-14884 Brand: SparkfunThis is a simple, subminiature size, axial lead mounted rectifier diode. Often used for reverse voltage protection, the 1N4004 is a staple for many power, DC to...
- Adafruit MiniBoost 5V @ 1A - TPS61023SKU: ADA4654 Brand: AdafruitThis adorable little board will come in very handy whenever you need a good amount of 5V power. It's the size of a linear regulator, but it's actually a mini-booster! Input 2-5VDC on one side, and get 5V at up to 1A supply on the other. Perfect for use with battery-powered projects with 2 or 3 Alkaline, or a single Lithium battery.
- Semi Flexible Monocrystalline Solar Panel (6V 1A)SKU: FIT0600 Brand: DFRobotThis powerful monocrystalline solar panel features an A-class monocrystalline silicon panel. Due to up to 21% conversion efficiency and waterproof design, you don't...
- Peltier Thermo-Electric Cooler Module - 5V 1ASKU: ADA1331 Brand: AdafruitKeep it cool with a Peltier module. These unique electronic components can generate a temperature differential when powered. That is to say, apply 5V to the red...
- SparkFun Motor Driver - Dual TB6612FNG (1A)SKU: ROB-14451 Brand: SparkfunThe TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the...
- Mini Snap-Action Switch with 13.5mm Lever: 3-Pin, SPDT, 1ASKU: POLOLU-1528 Brand: PololuThis miniature single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch or as a small tactile bump sensor for your robot. The switch body dimension is 12.8 × 6.0 × 6.5 mm, and the lever arm is 13.5 mm long.
- 24V DC 1A Fixed 2.1mm Tip Positive Appliance PlugpackSKU: AM8968B Brand: Core ElectronicsOverview 24V DC Switchmode Plugpack Supplied with fixed 2.1mm DC tip (tip positive). Compact design with high current regulated output. 24VDC @ 1A.
- Voltage Regulator - 12VSKU: COM-12766 Brand: SparkfunThis is the basic L7812 voltage regulator, a three-terminal positive regulator with a 12V fixed output voltage. This fixed regulator provides a local regulation, internal current limiting, thermal shut-down control, and safe area protection for your project. Each one of these voltage regulators can output a max current of 1.5A.
- 12V Step-Up Voltage Regulator U3V16F12SKU: POLOLU-4945 Brand: PololuThis compact (0.32"×0.515") switching step-up (or boost) voltage regulator efficiently generates 12 V from input voltages as low as 1.3 V and handles...
- 12V Step-Up Voltage Regulator U3V40F12SKU: POLOLU-4016 Brand: PololuThis compact (0.6"×0.6") switching step-up (or boost) voltage regulator efficiently generates 12 V from input voltages as low as 1.3 V and handles...
- 12V Step-Up Voltage Regulator U3V70F12SKU: POLOLU-2895 Brand: PololuThis powerful synchronous switching boost regulator efficiently generates an output voltage of 12 V from an input voltage as low as 2.9 V while using an...
- $1.65 AUD, inc GSTAs low as $1.52 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
How to Use DC Regulators/Converters
So, you might have the best project in the world, an amazing idea and design, but no matter how clever your circuitry or how advanced your prototype is, unless you can power your project correctly, it all counts for nothing. Often you will ...
Ohm's Law - Practical Examples for Makers
This tutorial is a guide to the Ohm's Law / Power cheat sheet. You may have arrived here because you received a cheat sheet with your Core Electronics order. If not, no worries! You can still follow along with the examples - we've pro...
How to Drive High Power LEDs – 3W Aluminum Backed Star LEDs
High power LEDs (Light Emitting Diodes) have different requirements that need to be met when compared to regular LEDs. Current regulation using only resistors is impractical so it is necessary to use a switched-mode voltage and current reg...
Our recommendation on Breadboard Power Supplies
So, you’re looking for the right way to power your breadboard? You’ve found that your Arduino Uno just doesn’t quite have the juice to power up your circuit. It's likely that the microcontroller can output around 400mA whe...
Power Supplies for your Project
Ever had the issue where you have dozens of old phone chargers and appliance plug packs piled up in a rats nest of AC-to-DC mayhem? We tend to breeze right past these square, black power supplies, not knowing what's happening under the hood...
Which Raspberry Pi Case is Best For You?
What’s even better than the world’s most popular microcomputer sitting on your desk? When it’s sitting there in a case which protects it, makes it easier to use, and gives your desk some style. If you buy a Raspberry Pi i...
Using Relays with Particle
So, you want to control things with your Particle Photon and/or Electron do you? Well, a relay is a perfect way to do that. Whilst there are many ways to control an electrical signal from digital logic such as transistors and optoisolators,...
Choosing Your Next LiPo Battery
As technology gets smaller and more powerful, wearables and portable devices are becoming more common in our everyday lives. Makers are looking to make projects portable and with that comes the need for high capacity batteries that are reli...
How to Flash/Write Raspbian OS onto Raspberry Pi Compute Module 4 (CM4)
While the Raspberry Pi Compute Module 4s (CM4s) share a lot with the regular Pi 4 Model B, getting started with the flashing process can be quite different depending on which model you pick! This article aims to demystify that, so without f...
Getting Started With Relays | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Relay is, why we might use one, how to choose a Relay, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A 5V SPDT Relay - I'll be using a 5V Single Channel Relay M...
Teensy Boards Compared
Hello everyone, how awesome are the Teensy boards from PJRC? Super awesome. And as with any product that has been around for a few years, and gone through various iterations, there’s now a few different boards to choose from, which ...
What is LattePanda?
If you’ve been around electronics for a while you’ll have noticed the trend of single board microcomputers targeted at hobbyists through to industrial projects, the most popular platform being the Raspberry Pi. Now the Raspberry...
Our Arduino SPI Tutorial
SPI stands for Serial Peripheral Interface and it is a way to send data between microcontrollers and other small devices. It is a synchronous data bus, meaning it uses a clock to regulate the data transfer. SPI is also Full-Duplex com...
Our tips for using NiMH Batteries
NiMH is an abbreviation for Nickel-Metal Hydride. NiMH batteries are some of the most common rechargeable batteries we see in consumer electronics. Due to their superior chemistry, NiMH batteries have taken over Nickel Cadmium Battery appli...
Powering Portable Projects: Batteries
Want to make your project portable? We've put together a quick guide to get you up to speed on battery options and help you decide which batteries might be best for your project. Batteries are a whole different game to plug packs and bencht...
How to Save Games on RetroPie
So you've got your brand new RetroPie gaming kit setup, but you've got no idea how to save your games. No one wants to be starting afresh each and every time they jump onto their Pi for some light gaming. I've put together this handy guide ...
Optimising RetroPie
Hello and welcome to another tutorial on the joys of RetroPie. Today we’re going to look at making RetroPie even better. If you’ve had the chance to play around with the RetroPie system, you’ll have noticed that whilst it ...
PiicoDev Ambient Light Sensor VEML6030 - Raspberry Pi Guide
Introduction This guide will help you read light intensity data from your PiicoDev® Ambient Light Sensor and a Raspberry Pi single-board computer To follow along, it's best to have: A Raspberry Pi (model 3, 4, Zero W) This tut...
Arduino Projects with Sound (Using Sparkfun RedBoard)
Project Set 2 – Sound Welcome to the second Project Set from the Sparkfun Inventors Kit V4.0 Guide! In our last Project Set, we explored the basics of the Arduino IDE, some electrical and electronic concepts and looked at vario...
Makerverse Micro SD Adapter - MicroPython Guide and Data Logging
Introduction This guide covers how to connect the Makerverse Micro SD Card Adapter to a Raspberry Pi Pico and program a basic data logging script in MicroPython. To follow along, it's best to have: A Makerverse Micr...
How to Use HC-05 Bluetooth Modules
So we’ve taken a look at what Bluetooth is in our Introduction to Bluetooth tutorial, and hopefully, you’ve found our Choosing a Bluetooth Module For Your Project tutorial useful in deciding which Bluetooth module is right ...
Arduino Projects with Motion (Using Sparkfun RedBoard)
Arduino Projects with Motion (Using Sparkfun RedBoard) Welcome to the Third Project Set from the Sparkfun Inventors Kit V4.0 Guide! In this tutorial, we will explore the operation of a Servo Motor and an UltraSonic Sensor in combination wi...
How to use Solar LiPO Chargers
Every day, Solar energy bombards Earth with about 173,000 terawatts of power. That's close to the yearly electricity bill for Planet Earth. Solar energy is free power from the stars. So the question stands, why aren't we using it more? Pric...
Motor Drivers vs. Motor Controllers
If you’ve ever built a robot with wheels, or any motorised parts really, you’ll have come across the issue of needing to drive it from your microcontroller. Because a standard chip is only able to output a small amount of curren...
Makerverse Motor Driver, 2 Channel - Application Guide
Introduction The Makerverse Motor Driver has been updated to a v20 design which now features a 5V output pin instead of the VM pin. Some images and in-video descriptions in this guide may be outdated This guide covers the use of the Maker...
All About LEDs
Hello and welcome to our tutorial where we a look at all things LED. Now first of all, what is an LED? LED stands for Light Emitting Diode and is an electronic component used to convert electrical energy to light energy. This process is cal...
Our Overview of Makeblock's Ultimate Kit 2.0
The aptly named Ultimate Kit 2.0 is the final kit in the line-up of educational robots from Makeblock. With over 160 independent mechanical parts and modules, the Ultimate Kit 2.0 answers the call for almost limitless creative freedom. Matc...
Python and MicroPython - Compare and Access
Both Python and MicroPython are powerhouse programming languages. Each of them is capable of supporting your programming needs to almost the limits of your imagination. Both languages are transportable, open-source, growing in popularity, c...
How to Choose a Bluetooth Module For Your Project
Alright, so we know that Bluetooth is awesome, and if you don’t, take a read of our Introduction to Bluetooth tutorial. But how exactly do we go about implementing Bluetooth communication in our projects? Well, fortunately for us, th...
Three Golden Rules for Choosing a Power Supply (No Maths!)
Often the last consideration in a maker project, the DC power supply is the heartbeat of many electrical projects and the correct selection requires some consideration. Power supplies go by a lot of different names, you can call them Wall ...
Gaming Kit for RetroPie
Video gaming has evolved tremendously over the last decade, console games produce near real-life graphics, and playing with friends across the globe is easier than sending a text message. This is all well and good, but there are those of us...
Configuring 8Bitdo N64 Controller Mapping
RetroPie is a fantastic system, and once you map your input device, it will take those mappings and apply them to all of the emulators on RetroPie. If you’re new to RetroPie and want to find out a bit more, take a read of our Gaming ...
Our Rigol DP-832 Power Supply Review
The Rigol DP-832 is a 3-channel, benchtop power supply suitable for a serious maker, makerspace or product developer. In this video I'll take you on a tour of the supply's operation and give my two cents on things I like and dislike. ...
How to Build Your Ultimate RetroPie Gaming Console
Amid all the new controllers that 8Bitdo have brought out and the mountain of Raspberry Pi cases and accessories that are available, we’ve bundled everything together to create the ultimate RetroPie gaming console. If you’ve bee...
Makerverse Real Time Clock with Supercapacitor Backup - Raspberry Pi Pico Guide
Introduction This guide covers the basic use of the Makerverse Supercap Real Time clock on the Raspberry Pi Pico using our RV3028 MicroPython module. The MicroPython module implements some commonly used features of the RV3028 RTC but is no...
Pycom Expansion Board 2.0 Overview
It would be good to have some understanding of Pycom microcontroller boards before reading this article. We won’t go into what capabilities each microcontroller board has. If you’d like an introduction, try our Pycom WiPy Overvi...
How to use Stepper Motors and DC Motors with a Raspberry Pi - Adafruit DC & Stepper Motor HAT
This guide will demonstrate exactly how to control Standard Stepper Motors and DC Motors with a Raspberry Pi Single-Board Computer. To do this as seamlessly as possible we will utilise a HAT. HAT stands for Hardware Attached on Top. HAT bo...
Getting started with your Onion Omega2/2+
In this tutorial we will learn how to set up the Onion Omega2/Omega2+ for the first time. You will require the following: Onion Omega2 or Omega2+ An Onion Omega2 Dock, such as: An Onion Omega2 dock, eg. Power Dock or Bre...
How to get started with Circuit Playground
Have you heard about the Circuit Playground? It's the new all-in-one electronics platform from Adafruit. It was created to bring all the fun features of electronics and physical computing to makers, but It's dead-simple to use, solde...
Onion Omega - First Time Setup Using the Command Line
In this tutorial, we will learn how to set up the Onion Omega2/Omega2+ for the first time using the command line. While the Omega2/2+ has a graphical setup wizard and a web-based GUI called the "Console," we have found both to ...
Unleash your creativity: 3D Printing with Soluble Supports
Recently, we got a brand new Dual Extruder v3 Tool Head from LulzBot and took a dive into the design of it, mainly, what makes it so great for Dual Extrusion with our 3D Printers. First, a quick recap, Dual Extruding is the process of using...
Boards of a Feather
Have you ever used an Arduino board, and wanted to hook it straight up to a JST connected LiPo battery but knew it wouldn’t work? Or maybe you wanted a microcontroller with built-in wireless capabilities? Well, Adafruit has developed...
8Bitdo NES30 Pro Controller Review
Today, we’re looking at the 8Bitdo NES30 Pro. It’s a newer controller from 8Bitdo and one that I’m really excited about. It’s an interesting gamepad, with the styling and form factor taking cues from both the classic...
How to Build Internet-Connected Electronics Projects
What do we mean when we talk about the "Internet of Things"? Mostly we're talking about tiny computers that have access to the internet and do some useful work. Unlike the computers we're used to holding in our hands, they don't have a touc...
Circuit Playground Express Workshop for Educators and Beginners
Welcome to the Circuit Playground Express Workshop! This workshop is geared toward educators and coding beginners, who want to get started programming with this easy to use platform. We will go over everything you need to know to get you st...
How to Pair and Map 8Bitdo SF30 Pro Controller with RetroPie
8Bitdo have brought joy to many retro-gaming enthusiasts with their SF30 Pro Bluetooth controller. It’s a fantastic piece of gear, and one of our favourite controllers to use with a RetroPie setup. We’ve covered off on our thoug...
Potentiometers and the Arduino Uno
Variable resistors come in all shapes and sizes, and they all do the same basic job. They allow you precisely control voltage/current flow within a circuit. The most common type of variable resistor we see in DIY electronics is the Potentio...
Infinity Mirror Kit V1 - Assembly and tutorials
The Infinity Mirror Kit is a desk-top display that creates a dazzling optical illusion - a tunnel of light that tears through space! Note: This tutorial is for the Infinity Kit V1. We updated have updated to the Infinity Kit V2 as of ...
Lightning Sensor with a Raspberry Pi Single Board Computer - 40 KM RADIUS RANGE!
What if I told you that you could have the power to detect a lightning strike from 40km away? You'd probably think I've gone mad watching too many Marvel movies. But it is true! All thanks to the DFRobot Gravity: Lightning Sensor. Accessib...
Our Recommendation for your first Benchtop Oscilloscope
You’ve been working on that project for days, even weeks, and you’ve gone through all the steps of the process; meticulously ensuring everything is above board. And yet, for some unexplainable reason, your circuit is acting out....
Ultrasonic Sensing with Pycom
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. One of the most common sensors in...
Printing with Rigid and Flexible Filaments
LulzBot have released the Aerostruder for both Mini and Taz Printers now (Mid 2018). It features a Titan Aero Extruder from E3D, which makes it capable of printing in flexible filament and rigid filament, depending on the situation! It's an...
Hello World! First Python Script
Python is a powerhouse programming language capable of supporting you throughout all your programming adventures. Making exciting and unique code is just flashes of comprehension away. For those just starting, looking at the Python Pr...
Choosing a Soldering Iron
Hello, and welcome to our tutorial where we’ll be looking at two different types of soldering irons and which one is going to be best for your workshop. We’ll be specifically looking at soldering irons, not how to solder, so for...
How to Create a NOOBS microSD Card
NOOBS has made installing Operating Systems (OS) on the Raspberry a super simple process. If you haven’t purchased a Raspberry Pi NOOBS MicroSD card, you can download NOOBS onto a blank SD card in a couple of quick, easy steps. ...
PiicoDev Real Time Clock (RTC) RV-3028 - Getting Started Guide
This guide will help you get started with a PiicoDev Real Time Clock. We'll set and read the time/date, observe the power-backup capability, and configure the RTC with an alarm. A Real-Time Clock (RTC) is a timekeeping device that accurat...
Python Rundown and Main Windows
This guide will be a rundown on Python, the open-source programming language built by the hugely intelligent Guido van Rossum. This guide will also contain external links to Python resources and download links. Programming is...
Improving 3D Printed Models - Ultimaker Cura
If your 3D printer is an Ultimaker S5 then your prints will almost always come out looking brilliant. Although achieving desirable 3D printed components can sometimes require troubleshooting to resolve print errors. These errors often can ...
What is Raspberry Pi?
Hi there! If you’re wondering what all the hype and interest surrounding Raspberry Pi is about, you’ve come to the right place. The original Raspberry Pi debuted in 2012, and is a credit card sized computer that has ports for U...
Let's take a look at Makey Makey!
Makey Makey is a compact circuit board which allows you to create circuits using anything you like and connect them up to a computer. You use alligator clips to connect things to the Makey Makey, and then your Makey Makey connectors to a co...
Windows 10 IoT on Raspberry Pi 3
Today we’re going to look at installing the Windows 10 IoT (Internet of Things) core onto a Raspberry Pi 3. Traditionally Windows has been the resident overlord of desktop devices, however in recent years we’ve seen it t...
Tweezers for Every Task
In case you haven’t noticed, when dealing with electronics, you’ll be picking lots of small things up, and it only gets harder when dealing with tiny SMD components. But whatever you’re working on, be it a breadboard proto...
Setting up your OctoPi Kit
So you have just received your OctoPi kit and you are looking to get it up and running. All you need to do is grab out all the parts you received and around 20 minutes of time. To connect your OctoPi to the network you need to decide what ...
Run Raspberry Pi x86 on your Windows Desktop Computer (Virtual Machine)
Running a virtual Raspberry Pi on your computer can be a neat way to experiment in a Raspbian-like environment without being tethered to a physical Pi. In this video, I'll walk you through the process of installing Raspberry Pi Desktop on a...
PiicoDev Servo Driver PCA9685 | Getting Started Guide
This guide will help you get started with a PiicoDev® Servo Driver module. We'll take a tour of the module and walk through some examples to drive common servos. Servo motors are integrated motors that contain their own power circuitr...
OctoPrint Integration with Cura 2.6+ Lulzbot Edition
OctoPrint Integration is one of my favourite new features in Cura 2.6+: LulzBot Edition. In short, this integration means that you can print and control your 3D Printer via it's OctoPrint server. All from within your slicer window on your P...
Our 8Bitdo SF30 Pro Controller Overview
The 8Bitdo SF30 Pro was launched at the end of 2017 by 8Bitdo in an effort to create the ultimate, ‘portable’ gaming controller. Having become known for their faithful recreations of vintage gaming controllers, the SF30 Pro is a...
Mobile Networks - Where Can My IoT Device Connect?
The Internet of Things (IoT) describes the network of physical objects that are all around us which are blessed with sensors, software, and other technology for the purpose of connecting and exchanging data with other devices and systems al...
Stress Testing Your Raspberry Pi (for Cooling and Overclocking)
We have a more recent guide to Stress testing your Raspberry Pi, this guide has been kept here for reference. Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what yo...
USB MIDI With Teensy
If you’re a musician or have had anything to do with the entertainment industry, you may have heard of the term MIDI before. MIDI stands for Musical Instrument Digital Interface and was created in the mid-80’s as a way to standa...
Choosing a Benchtop Power Supply
If you're looking for a benchtop power supply, but you're unsure of what you should be looking for in a decent supply for your workspace, we have got you covered with this guide. We will look at the specifications to look out for in a power...
What are Xbee Modules?
Wi-Fi, as we know it, is a form of wireless communication based on the 802.11 standards as outlined by the IEEE (the Institute of Electrical and Electronics Engineers). If you're paying attention to it, you'll notice an appendage to this st...
Raspberry Pi vs. LattePanda
Ah, what a glorious time we live in, where we have to compare which micro-computer is going to best suit our needs. If you’ve been in the maker sphere for just a short time, you’ll be sure to have heard of Raspberry Pi the mirac...
Raspberry Pi Generations Up To 2020
It is long overdue. Time for a table with all the info comparing every generation and style of Raspberry Pi from the genesis to now! We have come a long way to have our hands on the Raspberry Pi 4 Model B 8 GB so it is time we give you the ...
Circuit Playground Express TV Remote
Have you ever lost or broken a TV remote before it's time? Have you ever wanted to spice up the way you change channels or inputs on your TV? Have you got a greedy housemate who always steals the remote off you? If any of these are the case...
How To Setup Raspberry Pi Zero W Headless WiFi
So what does it mean to run headless?A computer setup without a monitor is said to be running headless. You might want to do this if you're installing your Pi into some project, or want to keep power-usage and cost minimal. This kind of se...
Our tips for Coin Cell Batteries
Firstly, what are Coin Cell Batteries? A coin cell battery is a flat, cylindrical battery used in a bunch of small electronics applications. You might have seen them in a wristwatch, remote control or any piece of wearable tech. Typically ...
Cooling Your Raspberry Pi
Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what you can do with it if you take a look under the hood. One of the most popular experiments to do with your Raspberry Pi is o...
Overclocking Your Raspberry Pi
Part of the joy that is Raspberry Pi is getting stuck into it at a slightly lower level and finding out exactly what you can do with it if you take a look under the hood. One of the most popular experiments to do with your Raspber...
Join the new age with a Mooshimeter
The multimeter is one of the essential tools in your electronics toolkit. These battery operated devices combine several measurement functions into one easy to use device. You can get Analog or Digital multimeters, each displaying your meas...
How GPS Receivers work
GPS is accurate and handy to use, so much so that we rely on it more and more every day. It's not often we take the time to learn how it works. The idea of GPS refers to a Global Positioning System; a collection of satellites in orbit above...
How to Use a LCD Screen/Display with Raspberry Pi
What fun would a computer be without a screen to see what you’re doing? Well if you own a Raspberry Pi and are curious about the different ways you can connect an external display or monitor up to it, then look no further. Today we&rs...
Getting Started with Servos | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Servo is, when we might use one, how to choose a Servo, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A Positional Servo, such as the Feetech FS90 Micro Servo A Con...
Rigol's PC software: Ultra-Sigma and beyond
The ability to connect your test equipment to a local PC is invaluable. It allows monitoring and the use of your equipment via a PC interface. That includes coveted mouse/keyboard control! This control centre capability is essential when yo...
Using NeoPixels with Particle
Life’s better in colour right? Then why are you still using boring old regular LEDs in your project, when you could be using addressable RGB LEDs. Now LEDS that have Red, Green, and Blue integrated in a single package are nothing new,...
Getting Started with Raspberry Pi Pico
This guide is a little outdated: Follow our updated guide for a much simpler way to get started! Contents Part 1 - Interacting Coding with the REPL Part 2 - Moving Beyond the REPL (with rshell) Part 1 - Interactive Coding with the...
PiicoDev Capacitive Touch Sensor CAP1203 - Raspberry Pi Guide
Let's get started with the PiicoDev® Capacitive Touch Sensor. In this guide, we'll connect the PiicoDev Capacitive Touch Sensor to our Raspberry Pi and get it working with some example code to detect touch events. We'll also remix the c...
Makerverse Audio Kit Guide | Play Music and Generate Tones
IntroductionWelcome to the guide for the Makerverse Audio Kit. This kit will allow you to build a music player, a musical keyboard, and a sound effect soundboard! To follow along you will need: The Makerverse Audio Kit The Makerverse ...
Basics: Getting Started with the Terminal on Raspberry Pi
In this tutorial we’ll be getting familiar with basic use of the Raspberry Pi terminal. We’ll cover navigating the file-system, making directories, writing and editing text files, and just touch on the use of wildcards. To get ...
Our littleBits Gizmos and Gadgets Kit (2nd Edition) Review
The new Gizmos and Gadgets revision 2.0 from littleBits is here and we've decided to review the kit for any budding inventors (or inventor's parents) out there. The v1.0 kit was impressive enough, we were interested to see what littleBits c...
MOSFETs for Makers: Getting Started with High-Power Control
In this guide, we’ll learn how to harness the power of MOSFET transistors to easily control higher-powered components like solenoids, motors, and Peltiers with a microcontroller. First, we will cover an easy-to-follow example using s...
Ultimaker 3D Printer Material Guide
One of the most critical parts of a successful 3D print is the correct material choice and through its careful consideration you will get the best result for the final component you had in mind. Ultimaker has a wide range of 3D printi...
Pycom Pysense Getting Started Guide
The Pysense expansion board from Pycom has many sensors. In Pycom Pytrack Getting Started, I showed how with some Processing code we can see the real-time position of the board in 3D. That project works with the Pysense too. How about we sh...
Raspberry Pi Pico Workshop for Beginners
Welcome to the Raspberry Pi Pico Workshop, where you will learn everything you need to know to hit the ground running and start making your own projects with the Raspberry Pi Pico and MicroPython. This workshop is designed for complete beg...
Cura 2: LulzBot Edition - An Overview for Beginners
Now that we are all on track with our Slicer software, having just installed Cura 2 and upgraded our printer firmware, let's work on turning some 3D Model files into G-Code for our 3D Printer to create. We're going to be using our LulzBot M...
Uninterruptible Power Supplies (UPS) With Raspberry Pi 4 Model B | PiJuice HAT
Now I'm not talking about a delivery service - I'm talking about an Uninterruptable Power Supply for your Raspberry Pi 4. So if your Raspberry Pi project needs to be powered all the time relying solely on the mains power system may leave y...
Servos, Steppers or Solenoids? | Choosing an Actuator to Move Your Project
In this guide, we go over some common ways of adding motion to your project with actuators such as stepper motors, servos and linear actuators, to help you choose which one is most appropriate for your situation. The start of this guide c...
Soldering 101
Imagine being a builder without a hammer, or a car without a brake, this is kind of useful, but nowhere near as useful as it could be. This is like being a maker/DIY’er/enthusiast without being able to solder. Sure you can breadboard ...
If, Elif and Else Keywords in Python
Continuing our Python journey deeper into this dynamo of a programming language we will immerse into the keywords | if |, | elif | and | else |. Imagine all these keywords as the traffic controllers telling the control flow w...
Identify Electrical Connectors
There are a ton of electrical wire connectors, too many to elaborate on in a single guide, however there are a couple of connectors that as a maker you will come across. Often when starting your way into the electronics world all you need ...
Pan-Tilt Hat with Raspberry Pi - Quick Start Guide
Pimironi Picade Pan-Tilt Hat lets you mount and control a pan-tilt module right on top of your Raspberry Pi palm-sized computer. Setting up a Pan and Tilt system has never been easier with absolutely no soldering required! Pe...
How to Build a RetroPie Console
Perhaps you’ve read our Gaming Kit for RetroPie tutorial on how to setup a RetroPie console and wondered what’s required to actually build one, or heard about it and not been sure what you need. Well, today is your lucky day bec...
Setting up Your Retroflag NESPi Case with a Heatsink and Cooling Fan
By now, you’ve probably seen the fancy new Raspberry Pi cases we’ve got available; the NESPi case by Retroflag. Designed and styled specifically for retro gaming systems such as RetroPie, it offers everything you need to turn yo...
Internet of Things with Pycom and Adafruit IO - From Zero to Hero
Introduction We’re going from zero to hero. Starting from nothing we’ll get a WiPy communicating with Adafruit IO, an IoT service out on the Internet. We’ll be able to send data from the device to the cloud and control th...
MicroPython Board Comparison
Welcome to the benchmarking arena! We are going to put eleven microcontrollers to the test and see how they hold up against a set of fiendish tasks that we devised to push them beyond their limits. We chose most of our candidates based on t...
WiFi GlowBit Matrix Control with WLED and ESP32/ESP8266 Dev Boards – Make Pixel Art with No Code!
Nothing beats bright shiny colourful lights and adding an extra dimension only makes them better. This guide demonstrates the fastest and most customizable way to have WS2812B grids of fully addressable LED Nodes come alive. Exactly ...
Set Up a Geophone with a Raspberry Pi and an ADC (ADS1115)
Geophones are devices that generate electric signals proportional to the particle velocity in a sound/compression wave. More simply a Geophone is a super low frequency microphone for the ground. Geophones are used around the world to measu...
Integrated Computer Vision Package - OAK-D Lite With Raspberry Pi Set Up
If you ever needed a performance boost when running Machine Learnt AI Systems (like facial recognition) with a Raspberry Pi Single Board Computer then I have a solution for you. The OAK-D Lite. The Oak-D Lite is the Leatherman Multi-tool o...
Raspberry Pi Workshop for Beginners
Welcome to the Raspberry Pi Workshop for Beginners! Here you'll be able to follow along with our series of bite-sized videos that cover everything you'll need to know to get started with your Raspberry Pi, and start making awesome project...
12V Portable Battery Box
This project creates a functional 12-volt portable battery case for camping or other outdoor activities.The battery box provides a 12V cigarette lighter socket for running lights with an on/off switch for ease of use. There is also an Ander...
Portable Arcade Emulator
Introduction
I am a Mechanical Engineer, and after 30 years in industry I now teach Engineering at High School. I create various projects in my spare time and bring them to school to inspir...
ATX Benchtop Power Supply
Despite having two high-quality variable (but analog) benchtop power supplies, I decided you can never have too many. I also specifically wanted a fixed, multi-output supply for standard project voltages such as 3.3V, 5V, 9V, 12V, ...
Despite having two high-quality variable (but analog) benchtop power supplies, I decided you can never have too many. I also specifically wanted a fixed, multi-output supply for standard project voltages such as 3.3V, 5V, 9V, 12V, ...
mmPi-Pico HAT
I use a Raspberry Pi running EmonCms for collecting sensor data and controlling devices around the home but several things have been on my To-Do list to enhance its functionality. A Shutdown/Power Down/Startup circuit. Proportional fan...
IoT Pet Feeder
The objective of this project was to create an Internet of Things (IoT) device that could give pet access to a food bowl when a text message command was sent from a remote location. I had never done an IoT project before, so I wanted to ke...
IoT Chicken Shed (Arduino, Wifi)
If you have chickens and find you're not always available to close the gate at night or check the water levels each day, then why not use an ESP8266 to automate your chicken door and receive alerts door status and low water level, as well a...
Camera Dew Controller
Introduction My passion hobby is night-time time-lapse photography and astrophotography/nightscapes. This means a lot of time spent outside in the dead of winter overnight and an issue that I faced was dew condensing on the lens. This is...
Auto Tracking Camera System
The purpose of this project is to design a system that will automatically track stars or satellites. The first version, described here, is specifically to track stars and operate a Raspberry Pi HQ camera to take a series of long-exposure im...
Automatic Bike Indicators
This project uses an Accelerometer to detect when you are leaning left or right. Depending on if/where you are leaning, it will flash LEDs on the right or left of the bike's rear. Powered by an Arduino and a 12v battery pack (my case 8 AA B...
ESP32 IR-Triggered Camera with Home Assistant Integration
I love the ESP line-up. I started by messing around with the ESP8266 and I completely fell in love with it. The 8266 is all I ever wanted from a microcontroller: WIFI connectivity, a decent amount of GPIO, a deep-sleep mode for batter...
Time lapsing in OctoPrint (Properly!)
Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosure, I'm just about ready to turn on some serious 3D printing work. But before I dive into that endless pool of fun, it's a good time to take ...
IoT House
These days we can do just about anything on our phone, we can control so many aspects of our lives using the technology in our pocket, but the most mundane aspects of our lives; opening the garage door, blindly reaching for the light switch...
RPi Cluster - SETI@Home
I was interested in creating a RPi Cluster to learn about how they work. After getting the clusterhat and Pi Zero Ws I set about creating the images for 5 sd cards. This seemed a waste so I scrapped that idea and setup the image for one sd ...
Racing Simulator Motion Platform
Hi. My son and I have made our first Racing Simulator Motion Platform. It has been a challenge but we now have a playable situtationIt has been a long journey, starting off with info from the great people at www.xsimulator.net and a lot of ...
ThingSpeak temperature & pressure logger
This project logs temperature and pressure observations to a ThingSpeak channel using an ESP8266 WiFi module.
For this project, I designed my circuit and ordered a PCB using easyEDA. The project gets power from a USB port and uses a...
For this project, I designed my circuit and ordered a PCB using easyEDA. The project gets power from a USB port and uses a...
safePower
I like working with the Pi Zero W and Pi 4 as they are very compact, very powerful and very cheap for the capability they offer. I want to use them on small projects, stand-alone, and can't always guarantee power. As we know most Pi's don't...
WiFi Garage Door Controller with Raspberry Pi Pico W
I strapped a Raspberry Pi Pico W to my garage door motor and now I can control my garage door from my phone! The Pico W hosts a simple webpage on my local network with three control buttons - one for Up, Stop and Down. Pressing one of...
Modify Dell multimedia keyboard from USB bus power
This project is to modify a Dell multimedia keyboard into a Raspberry Pi Zero dedicated keyboard with external powered USB hub. You can find this article in my blog http://sizeofinfinity.blogspot.com.au/2017/06/modify-dell-multimedia-keyboa...
Hot-Wire Bender for Acrylic
A simple, and affordable build that produces sharp, and consistent heat-bends. A nichrome wire heats a channel. Place the acrylic over the channel, wait for it to reach temperature, and pull the hingeing section to create a bend.
&l...
&l...
Keypad entry to caravan using Arduino
I used to sleep in a caravan on my grandparent's property and as amenities were inside the house I had to go in and out of it quite regularly. I got sick of fumbling around with keys to go in and out of my caravan, so this project uses an A...
Roverling
Introduction
My first 3D printer was a CTC generation 2 clone of MakerBot ‘The Replicator Dual’, circa 2012. It died a little while back and has since been replaced ...
PowerPlay SSR Control
Introduction
The aim of PowerPlay is to provide an Arduino platform for managing downstream Solid State Relays (SSR) simply and safely. PowerPlay consists of a custom Arduino Shield, ...
Mini Desk Vacuum
Chances are if you are anything like me, being a maker is often an excuse to create as big of a mess as possible during the duration of a project. And after the project is finished? You are left with an enormous mess to clean up, taking awa...
Borg Cube for Scouts STEM Camp
Introduction
What does one make for a Startrek-themed STEM camp for Scouts? Especially when given the Search and Rescue (SAR) activity base to run. Why this base you ask? Usually I run a radio d...Introduction
What does one make for a Startrek-themed STEM camp for Scouts? Especially when given the Search and Rescue (SAR) activity base to run. Why this base you ask? Usually I run a radio d...
Duck Off! A Duck Repellent Device
Introduction
We live on a rural property and have around 20 to 40 wild ducks around at any one time. We have a large dam and jetty, however it is almost unusable due to all the ...
Environment Monitor - V2
This project started due to the smoke haze that enveloped our area during the 2019 and 2020 bushfires. I wanted something to check the air quality of my home and maybe find areas where it needed better sealing. In addition, the BMP280 senso...
Desktop Infinity Mirror (Lasercut!)
A smaller version of our amazing Infinity-Mirror Table - the Desktop Infinity Mirror compresses all the colourful goodness into a picture frame-sized display. The entire design is made from laser-cut acrylic that we cut in-house. Check out ...
RPi Garbage Bin Reminder
Our local council picks up recycling bins one week and green waste the following week. Sometimes people forget which bins go out each week and perhaps they mistakenly put the wrong bins out. Not that that has ever happened to me of course! ...
Smart Watering System
Introduction This began as an idea after building a very basic single-channel unit. Commercial smart watering systems use a Wifi connection to the internet and get weather reports to determine the level of watering required. These systems...
Concrete Lamp
The concrete body of the lamp (which, to my eye look a bit like a leek) is made is two halves. The 1st and 2nd halves are cast in 2 steps using the same mould twice. I had a few failed attempts at making the mould entirely from sta...
The concrete body of the lamp (which, to my eye look a bit like a leek) is made is two halves. The 1st and 2nd halves are cast in 2 steps using the same mould twice. I had a few failed attempts at making the mould entirely from sta...
Bill of Materials
grinder_timer
Making a dumb coffee grinder slightly less dumb. This is a programmable timer tethered to a Rancilio Rocky coffee grinder. The Rocky is a "dumb" grinder and electrically very simple. Basically it's an ac motor with an on/off switch and a m...
Articulated Mule
Converting a Mule into an articulated 4 wheel vehicle. A 'Mule' is/was a hand trolley with a motorised elevatable platform. What for? Just for fun, want to be able to control it using the R2D2 droid inventor app via LittleBits boards, why ...
Smart Home Makeover with HomeAssistant
IntroductionI wanted to bring ageing, and failing, Home Automation infrastructure into the modern age whilst retaining hardware investments already made. Our house had Universal Power Bus (UPB) dimmers and switches installed at build time...
House Power and Solar Monitor
I’ve had a Current Cost Power Monitor for a number of years which worked well until we put solar on the roof. The Current Cost can’t determine which direction the power is flowing and so power generation and con...
I’ve had a Current Cost Power Monitor for a number of years which worked well until we put solar on the roof. The Current Cost can’t determine which direction the power is flowing and so power generation and con...
Solar Charging Station
The aim of this project was to use the sun to charge some batteries with 1W and 2W Seeed solar panels. The DFRobot Solar LiPo Charger and a Sunflower Solar Power Manager were purchased. Initially, this was unsuccessful because I did no...
Garage Door Sensor
This project uses a US100 ultrasonic distance sensor to detect instances of a garage tilt door being left open and sends an alert via the IFTTT mobile app. Additionally, the device logs temperature and pressure to a Thingspeak channel using...
Arduino Tide Gauge
I used an Arduino and a US-100 ultrasonic sensor to make an extremely low-cost tide gauge. This project measures the tide by sensing the distance to water using a US-100 ultrasonic sensor. The device has a 3D printed base&nb...
RetroPie in a Cartridge
For $50 and some dedication a retro gaming console can be yours and with HDMI you can play it with any modern TV or monitor. Instead of using bulky and space taking cartridges and discs it's all on the console. For this build, we're going ...
Mini NES Style Game Console with Raspberry Pi
My son really wanted one of the mini NES when they were released, however he missed out. I already knew that you could use a raspberry pi as an arcade emulator, so I thought why not build him one.
I grew up playing old arcade machi...
I grew up playing old arcade machi...
Simple Relay Timer
Introduction This project started because I needed to replace a water tap timer that had seen better days. The aim was to use a Raspberry Pi Pico and a couple of PiicoDev boards to do what the water timer did. The actual stopping a...
DIY Gameboy based on Raspberry Pi Zero W (PiGRRL)
We made a Pi Zero W retro-games console! The nostalgia is making me dizzy! If you'd like to build your own, we've put together a couple of wishlists to make things easier: For the Pi Zero W build, like in this project, check out the PiG...
Coffee Grinder With Arduino
Using a few bits and pieces, this ordinary coffee grinder now has two presets to run the motor for a programmable length of time. The idea being that the grinder running for a set amount of time will deliver a certain amount of coffee each ...
Rooberry Pi
In the area I live, there are often kangaroos that jump in front of traffic, often from blind spots, and can get themselves into harm's way. I wanted to build a low-cost solution that can alert drivers to kangaroos in these blind spots to r...
Makey Makey Skill Tester
This is the third project I've put up using the Makey Makey, and it's incredible fun, but it's also the simplest. Today I'm going to show you how to make a simple Skill Tester game complete with sound effects using a Makey Makey board and s...
IoT Mailbox
Getting letters and parcels is awesome, what’s not so awesome though is when you miss the postman and you don’t know if that important bit of mail arrived or not. Such a frustrating, yet mundane problem can be solved by creating...
Fruit and Veggie Gaming Controller
In preparation for some Maker Faire's we were heading to last year, I wanted to combine the awesomeness of the Makey Makey platform, with the fun that is RetroPie. For those who don't know the Makey Makey, it's a fantastic platform that all...
Stream Airplay to Your Pi Zero
The Raspberry Pi Zero W is a tiny, yet powerful little device. Coupled with a Pimoroni Speaker pHat, it can be easily turned into a portable Airplay speaker which allows you to stream your music anywhere you want.Parts you'll need: Raspb...
Infinity-Mirror Table
An infinity mirror creates a striking optical illusion - a tunnel of light that seems to tear through space. I built this infinity-mirror table using some addressable LEDs, a Particle Photon and easily obtainable timber supplies. Check out...
The Amazon Alexa-Enabled Smart Pool System
This project is to allow remote control of my pool and associated lights with a dedicated display inthe house, a phone application and Amazon Alexa. Any and/or all of these input devices may be usedto control the pool. The pool temperature ...
IoT Plant Monitor
So, my wife wanted to have some small plants in the house. I didn’t, so we compromised, and got some plants. The only thing is that neither of us remembers to water them, so I wanted to build a sensor array to monitor the moisture con...
Wefted Waveforms
This project aims to fuse neopixel strips with papier mache and origami into a free-standing electro-sculpture. The freestanding structure is formed from wire mesh and papier mache. It is then painted and wired up with strips of LEDs conne...
GraviTrack Enhancements - Lights and Sound
Introduction Searching for solar panels and related items on the Core Electronics website; I came across the Solarbotics GraviTrack Marble Machine Kit. I thought the kit would be a good educational tool for the grandkids. The kit was a hit...
IoT Soundscape
I had been captivated by the sound levels of trains I could hear passing by Metford throughout the day/night. I wondered if a sound level sensor reporting data back over LoRa would help me understand when a train was noisy. I also like the ...
SOLARBOI
Since I was young, I've always loved to explore. Over the years, I've tinkered with RC cars and played with planes, which were always plenty of fun. But I always dreamed of going out further - out into the real world, far beyond the confine...
Accurate IoT Clock With ESP8266
Being punctual is important. Hence accurate time is required. Clocks tend to miss out when it comes to accuracy especially when they are set by the user. So, why not get accurate time from the internet and use tried and tested hardware to ...
Makers love reviews as much as you do, please follow this link to review the products you have purchased.