Search results for: 'usb i2c'

You just found the perfect I2C sensor, and you want to wire up two or three or more of them to your Arduino when you realize "Uh oh, this chip has a fixed I2C address...

You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise...

ESP32-S3 4.3inch Capacitive Touch Display Development Board, 800×480, 5-point Touch, 32-bit LX7 Dual-core Processor, Up to 240MHz Frequency, Supports WiFi...

The HUSB238 USB PD sink chip is neat in that you can either use jumpers (really, resistor selection) to set the desired PD voltage and current or you can...

The HUSB238 USB PD sink chip is neat in that you can either use switches (really, resistor selection) to set the desired PD voltage or use I2C for dynamic...

This 2-Channel I2C to 0-10V DAC module can output a voltage of 0-5V or 0-10V, which can be widely used with most 0-10V devices on markets such as light...

Solenoids are a little like cats: if your project has one solenoid you'll probably stick with just one and in such cases our single MOSFET driver will...

This USB to TTL converter combine the USB-232-1 (USB to Single RS232 Adapter) and TTL-232-1 (Port-powered RS232/TTL converter) allows you to convert USB to TTL/CMOS compatible levels and vice versa.

The Gravity 4Pin IIC/I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 30cm length. One side is PH2.0-4p connector and the other side is XH2.54...

We launched the Serial CAN Bus Module years ago, which is very practical and easy to use. Now we have slightly modified the Serial CAN Bus...

This USB-to-serial adapter lets you easily connect a TTL serial device to a PC by acting as a virtual serial port. The board is a Micro-USB carrier for ...

The DS1307 Real Time Clock developed by one of our designers: Waiman. The module comes fully assembled and pre-programmed with the current time (ok, so it's our current time - MST).

The Gravity 4Pin I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 50cm length. One side is PH2.0-4p connector and the other side is XH2.54 DuPont...

This is an I2C DAC module that outputs 0-25mA current. It offers more accurate 4-20mA current output after calibration, which can be used with most 4-20mA...

No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter cable will be able to get...

This module enables galvanically isolated bidirectional I²C communication between two devices while supplying regulated, isolated power to the target. The...

Sometimes you'll find yourself with an I2C bus controller on one side, and an I2C bus device on the other and you gotta keep em (electrically) separated. Maybe because one is Earth-grounded, maybe because you've got some funky power monitoring setup, maybe you want to reduce noise.

The ANO rotary encoder wheel is a funky user interface element, reminiscent of the original clicking scroll wheel interface on the first iPods. It's a...

A 16-bit self-calibrating analog-to-digital converter that operates on I2C

The Adafruit TCA4307 Hot-Swap I2C Buffer breakout here solves that problem. It's specifically designed to take a non-hot-swap protocol (I2C) and protect the controller from wayward peripherals messing with the bus during attach/detach.

This module enables galvanically isolated bidirectional I²C communication between two devices. The bidirectionality applies to both SDA and SCL, which...

The FT230X USB Bridge is a compact USB to serial UART interface IC, engineered with an optimized pin count for space-constrained applications. It provides...

Back in my day, we used to have these big chunky PC joysticks that would plug into the back of your PC. No, not through USB, they had a DE-15 port and...

Explore M5Stack's DAC2 I2C Unit featuring the GP8413 chip, offering dual-channel digital-to-analog conversion with 15-bit resolution and precision up to 0.01% linearity for accurate voltage control and signal processing applications.