Search results for: 'rs-232 to serial converter'

USB to RS232/485 Serial Converter, Onboard Original FT232RNL Chip, Multiple devices applicable, Multi-OS compatible...

A nifty RS232 (DB9) to Serial converter. Comes with pre-soldered 0.1" male header pins for easy connectivity to breadboards and projects.

FT232RNL USB TO RS232/485/422/TTL Interface Converter, Industrial Isolation

RainbowLink USB protocol converter with 4 independent channels (RS485, RS232, 2 TTL) designed for efficient multi-channel serial communication. It offers...

No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter cable will be able to get...

If you're looking to interface with telco, retro or industrial equipment you'll probably run into RS-232 interfaces. The Adafruit RS232 Pal - Two...

There are a lot of devices out there that still communicate over RS232 but we bet your new laptop isn’t one of them. Don’t worry, though, we’ve got you covered. This 6ft converter plugs into your computer’s USB port and provides you with a DB-9 RSR232 connection. After installing the drivers onto your Windows, Mac or RedHat Linux system, the FTDI chipset inside the cable will enumerate as a COM port with a baud rate adjustable to whatever setup you want to connect to.

Are you troubled by the various level standards and voltages of the serial port? This 6-in-1 USB to Serial Converter is just right for you. Check it out! One module...

This RS232 shield is designed for the Arduino controller,and it can easily convert UART to RS232 interface. The shield integrates DB9 connectors (female) that provide connection to various devices with RS232 interface. Also the RS232 headers will facilitate your connections and commissioning. It provides the welding areas to make full use of extra space on it, which is highly convenient for prototyping. It provides a run / program mode switch. When switched OFF, you'll be able to programme the Arduino controller; When switched ON, you can use the shield normally. Gold immersion PCB. Long pins on the back that are compatible with most Arduino controllers.

2-Channel Isolated RS232 Expansion HAT for Raspberry Pi, SC16IS752+SP3232 Solution, with Multi Onboard Protection Circuits

If you want to interface with telco, retro, or industrial equipment, you'll probably run into RS-232 interfaces. The Adafruit RS232 Full-Pinout...

Industrial Isolated USB To 4-Ch RS485 Converter (B), CH344L Chip, Multi Protection Circuits, Multi Systems Support, Aluminium Alloy Case, Wall-Mount &...

The ‘must have’ IC for 3V projects. This is the RS232 converter IC that is capable of running at 3V and communicating with 3V logic. Comes in an easy to solder 16-Pin SOIC SMD package. Requires four external 0.1uF ceramic capacitors - no more 10uF monsters! Operates from 2.7V to 6V.

This adapter helps to connect TTL (Transistor-Transistor Logic) level signals to RS232 interface.

If you want to interface with telco, retro, or industrial equipment, you'll probably run into RS-232 interfaces. The Adafruit RS232 Full-Pinout...

This deluxe serial port adapter (RS-232 adapter) converts logic-level signals to the higher voltages required for RS-232 and similar serial ports. Unlike competing units, the Pololu serial adapter operates over a 3-5.5 V supply range and gives you access to all eight of the signal lines available on a DB9 connector, including five transmit lines and three receive lines.

The Serial Pi Plus is a communication board supporting the RS232 serial protocol.

Multiplexer has a set of interfaces for a variety of multi-function adapter plates. It supports USB, TTL, RS232, RS485 interfaces between the system conversions. What's more powerful is that it also supports one input multiple outputs, which greatly facilitates the communication between various controllers.

No matter what serial-esque protocol you need to interface with, this USB to Multi-Protocol Serial adapter will be able to get this-connected-to-that. It...

This item is the partial kit version of the 23201a serial adapter. All surface-mount components are assembled; the 0.1″ breakaway male header strip and DB9 connector are included but not soldered.

The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice versa (TX and RX). This will allow a microcontroller to communicate with a computer. Shifter SMD is powered from the target application and can run at any voltage! That’s right - power the board at 5V and the unit will convert RS232 to 5V TTL. Power the board at 2.8V and the Shifter board will convert RS232 to 2.8V CMOS TTL. Includes two indicator LEDs for TX and RX. Runs from 300bps up to 115200bps.

Raspberry Pi RS232 Board v1.0 is a standard communication port for industry equipment.This module is base on MAX3232,which is a dual driver/receiver that...