Search results for: 'jst sh breakout boards'

These simple boards serve as adapters between a JST SH-style 2-pin male connector and breadboard-compatible 0.1"-pitch through holes.

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

These simple boards serve as adapters between a JST SH-style 5-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

These simple boards serve as adapters between a JST SH-style 4-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

This 12 cm (4.5") cable has six 28 AWG wires and a 6-pin female JST SH-type connector that works with our Micro Metal Gearmotor Encoders with top-entry...

These simple boards serve as adapters between a JST SH-style 3-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

This simple board serves as an adapter between a JST PH-style 3-pin, side-entry connector and breadboard-compatible 0.1"-pitch through holes. The PH...

This simple board serves as an adapter between a JST PH-style 2-pin, top-entry connector and breadboard-compatible 0.1"-pitch through holes. The PH...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

This little breakout makes it easy to add a single NeoPixel to a project, with mounting holes and a pluggable connector. The PCB is less than...

This 40 cm (16") cable has six 28 AWG wires and 6-pin female JST SH-type connectors on both ends. These connectors work with our Micro Metal Gearmotor ...

These simple boards serve as adapters between a JST SH-style 4-pin male connector and breadboard-compatible 0.1"-pitch through holes.

This simple board serves as an adapter between a JST PH-style 5-pin, side-entry connector and breadboard-compatible 0.1"-pitch through holes. The PH...

These simple boards serve as adapters between a JST SH-style 2-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

This 10 cm (4") cable has six 28 AWG wires and 6-pin female JST SH-type connectors on both ends. These connectors work with our Micro Metal Gearmotor ...

This 30 cm (12") cable has six 28 AWG wires and a 6-pin female JST SH-type connector that works with our Micro Metal Gearmotor Encoders with top-entry...

This 63 cm (25") cable has six 28 AWG wires and 6-pin female JST SH-type connectors on both ends. These connectors work with our Micro Metal Gearmotor ...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

This 16 cm (6.3") cable has six 28 AWG wires and 6-pin female JST SH-type connectors on both ends. These connectors work with our Micro Metal Gearmotor ...

An exotic new microphone has arrived in the Adafruit shop, a PDM MEMS Microphone! PDM is the 'third' kind of microphone you can integrate with electronics, apart...

We got a request from a customer for a board that makes connecting between a breadboard and Stemma QT or Qwiic components easy, and here's what we...

By customer request, this is a DS2484 Stemma QT board that uses a I2C-to-1W controller chip, with ESD protection and support for split supplies. You can...

This 75 cm (30") cable has six 28 AWG wires and a 6-pin female JST SH-type connector that works with our Micro Metal Gearmotor Encoders with top-entry...

This simple board serves as an adapter between a JST PH-style 4-pin, top-entry connector and breadboard-compatible 0.1"-pitch through holes. The PH...

The Adafruit Pi Stemma is a small, easily removable breakout that easily adds a 4-pin JST SH pin (Stemma QT or Qwiic) connector to your Raspberry Pi. The...

This simple board serves as an adapter between a JST PH-style 6-pin, top-entry connector and breadboard-compatible 0.1"-pitch through holes. The PH...

You just found the perfect I2C sensor, available in a handy chainable Qwiic, or STEMMA QT package, and you want to wire up two or three or four of them to...

The AHT20 is a nice but inexpensive temperature and humidity sensor from the same folks that brought Adafruit the DHT22. You can take sensor readings as often as you like, and it uses standard I2C so its super easy to use with any Arduino or Linux/Raspberry Pi board.

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch...

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for...

A Raspberry Pi mini HAT designed to help you take the best possible care of your plants. It can tell you how well they're hydrated, attract your attention...

Connect your microcontroller to 4G LTE networks worldwide with the Clipper Cellular Breakout Board, featuring SP/CE compatibility, SMA antenna support, and seamless integration with Raspberry Pi and RP2040 devices.

Hey rocket man (burnin' out your fuse out there alone) ever wonder how fast you're rocketing? The Adafruit ADXL375 High G Accelerometer is an epic...

This 25 cm (10") cable has six 28 AWG wires and 6-pin female JST SH-type connectors on both ends. These connectors work with our Micro Metal Gearmotor ...

Ding dong! Hear that? It's the PiCowbell ringing, letting you know that the new Adafruit PiCowbell Proto is finally in stock and ready to assist your...

This board is an integrated solution for monitoring voltage, current, power, and other parameters in AC and DC systems featuring Allegro’s...

Qwiic, or STEMMA QT, is a very efficient way to quickly prototype an idea, but a lot of Qwiic/Stemma QT driver boards only have one port, and devices have...

Add quadrature encoders to your micro metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and hall effect sensors to provide 12 counts per revolution of the motor shaft. The sensors operate from 2.7 V to 18 V and provide digital outputs that can be connected directly to a microcontroller or other digital circuit.

Add smart light and sound effects to models and dioramas with this small-but-mighty RP2040-powered programmable controller board...