Adafruit NeoPixel UV LED Strip with 32 LED/m - White PCB - 1M

SKU: ADA3851 Brand: Adafruit
What new iteration of NeoPixel strip is this? Roll out the black light and disco ball! It's an Adafruit NeoPixel Ultraviolet Strip with 32 LEDs per meter! Each order...
$43.60 AUD, inc GST
$39.64 AUD, exc GST

In stock, ships same business day if ordered before 2PM
Fastest delivery: Tomorrow* Disclaimer:
The shipping address needs to be in the AusPost next day network and eParcel Express is chosen during checkout. On rare occasions, orders may be delayed by up to one business day due to AusPost pickup timings or for order verifications.

Quantity Discounts:

  • 10-25 $38.45 (exc GST)
  • 25+ $37.65 (exc GST)
- +

1 from local stock, 1 supplier stock; your order will dispatch between Dec 1 to Dec 10. And yes, stock levels and lead times are accurate!

Shipping:

  • $7+ Standard (5+ days*, tracked)
  • $11+ Express (2+ days*, tracked)
  • FREE Pickup (Newcastle only - must order online*)

Shipping costs may increase for heavy products or large orders.

Exact shipping can be calculated on the view cart page.

*Conditions apply, see shipping tab below.

What new iteration of NeoPixel strip is this? Roll out the black light and disco ball! It's an Adafruit NeoPixel Ultraviolet Strip with 32 LEDs per meter! Each order comes as a single one meter long strip. If you order multiple meters, you'll get that many individual 1 meter pieces.

The strip is made of flexible PCB material, and comes with a weatherproof sheathing. You can cut this stuff pretty easily with wire cutters. There are cut-lines every 3cm (1 LED each). Solder to the 0.1" copper pads, and you're good to go. Adafruit have a 5V/2A supply that should be able to drive 1 or more meters (depending on use) and a 5V/10A supply that can drive 5 meters (or more, if you are not lighting up all the LEDs at once) You must use a 5V DC power supply to power these strips; do not use higher than 6V, or you will destroy the entire strip. Yikes!

Comes with a 2-pin JST SM connector on each end. 

To wire up these strips we suggest picking up some JST SM plug and receptacle cables. Please note, Adafruit try hard to get consistent wiring between batch of strip but Adafruit can't guarantee it. Please double check which side is the input and which is the output by looking at the strip for the directional arrows and pin labeling

You can use these with any 'NeoPixel' or WS2812 driver (FastLED, etc). The R, G and B channels translate to the three individual UV diodes. so they recommend you pretty much just set all three channels to the same value, ranging from (0, 0, 0) to (255, 255, 255) to change the brightness of the three UV LEDs inside each 5mm x 5mm package.

Product Comments

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

  • $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
  • $7+ for Standard Post (typically 6+ business days, tracked)
  • $11+ for Express Post (typically 2+ business days, tracked)
  • Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

  • $12+ for Pack and Track (3+ days, tracked)
  • $16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review

Videos

View All

Guides

WLED Phone App | Control Addressable LEDs with an ESP32 or ESP8266

Today will be all about controlling Fully Addressable LED Lights using any Espressif ESP32 Dev...
Today will be all about controlling Fully Addressable LED Lights using any Espressif ESP32 Dev...

WS2812 / NeoPixel Addressable LEDs: Pycom Quickstart Guide

Sometimes all a good Pycom project needs is some colourful lights! This tutorial demonstrates h...
Sometimes all a good Pycom project needs is some colourful lights! This tutorial demonstrates h...

WS2812 / NeoPixel Addressable LEDs: Arduino Quickstart Guide

This tutorial is aimed at getting some instant gratification from your WS2812 LEDs (also known as Ne...
This tutorial is aimed at getting some instant gratification from your WS2812 LEDs (also known as Ne...

WS2812 / NeoPixel Addressable LEDs: Particle Quickstart Guide

This tutorial is aimed at getting some instant gratification from your WS2812 LEDs (trade name: NeoP...
This tutorial is aimed at getting some instant gratification from your WS2812 LEDs (trade name: NeoP...

Projects

Aircraft Lighting Model

The aim of this project was to create a working model of the aircraft exterior lighting systems. Ini...
The aim of this project was to create a working model of the aircraft exterior lighting systems. Ini...

HUGE LED Pixel Panel

I’ve always been fascinated by LED screens and seeing beautiful colours mix and merge to creat...
I’ve always been fascinated by LED screens and seeing beautiful colours mix and merge to creat...

Time lapsing in OctoPrint (Properly!)

Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosur...
Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosur...
Feedback

Please continue if you would like to leave feedback for any of these topics:

  • Website features/issues
  • Content errors/improvements
  • Missing products/categories
  • Product assignments to categories
  • Search results relevance

For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.

Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.

Makers love reviews as much as you do, please follow this link to review the products you have purchased.