Search results for: 'l298n'

Schottky diodes are known for their low forward voltage drop and a very fast switching action. This 1A 40V Schottky diode is ideal for use with motor drivers such as the L298N.

This is an ultra small Dual DC motor driver for some room limited projects. UVLO (Under Voltage Latch-Out) features a safe guard for your system. It is very considerate to own an Photo Coupler isolation for all the signals in case of that the motor's Reverse Current would interfere the control signals. Besides all, all the interfaces includes ESD (electro-static discharge) protection.

This is an ultra small size DC motor driver for room limited projects, while the impressive IC - LM2575 could provide a powerful way to drive 36V@15A motors. Also its UVLO (Under Voltage Latch-Out) feature provides a safe guard for your system. Besides all, it is very considerate to own an 5V output for Arduino or any other devices, and its interface is ESD (electro-static discharge) protection.

Our Black Edition A4988 stepper motor driver carrier is a higher-performance drop-in replacement for the original A4988 stepper motor driver carrier. It features a four-layer PCB for better thermal performance, allowing the A4988 microstepping bipolar stepper motor driver to deliver approximately 20% more current than Pololu's two-layer (green) version. Like Pololu's original carrier, the Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling. This board ships with 0.1″ male header pins included but not soldered in.

This tiny breakout board for TI’s DRV8835 dual motor driver can deliver 1.2 A per channel continuously (1.5 A peak) to a pair of DC motors, and it supports two possible control interfaces for added flexibility of use: IN/IN and PHASE/ENABLE. With an operating voltage range from 0 V to 11 V and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature, this driver is a great solution for powering up to two small, low-voltage motors. The carrier board has the form factor of a 14-pin DIP package, which makes it easy to use with standard solderless breadboards and 0.1″ perfboards.

Run four solenoids, two DC motors or one bi-polar or uni-polar stepper with up to 600mA per channel using the L293D. These are perhaps better known as "the drivers...

This motor speed controller is a compact, easy way to control the speed and direction of a brushed DC motor! Just plug in.....

This powerful motor controller makes basic control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five...

This powerful motor controller makes basic control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five...

Faster, cheaper, smaller, better, right? The SN754410 Quad Half H-Bridge is just that. Capable of driving high voltage motors using TTL 5V logic levels, the SN754410 can drive 4.5V up to 36V at 1A continuous output current! Please see datasheet for more information. This is a pin to pin compatible replacement for the L293D.

This is a breakout board for the L298N full-bridge dual motor driver; which comes in a staggered, Multiwatt package.

The Motoron M2U256 Dual I²C Motor Controller offers a compact solution for controlling two DC motors using a UART serial interface. Multiple Motoron...

The Motoron M1U256 Single I²C Motor Controller offers a compact solution for controlling two DC motors using a UART serial interface. Multiple Motoron...

An H-bridge DC motor driver with configurable current limit (0.2 or 1A) and up to four different I2C addresses. Great for DIY robot builds.

This powerful motor controller makes basic control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five...

The Motoron M2U256 Dual I²C Motor Controller offers a compact solution for controlling two DC motors using a UART serial interface. Multiple Motoron...

This powerful motor controller makes basic control of a brushed DC motor easy, with quick configuration over USB using our free software. It supports five...

This version is item #5340 with soldered header pins, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. It...

The MCP motor controllers from Basicmicro (formerly Ion Motion Control) can control a pair of brushed DC motors using USB serial, TTL serial, RS-232...

The Motoron M1U256 Single I²C Motor Controller offers a compact solution for controlling one DC motor using a UART serial interface. Multiple Motoron...

The MCP motor controllers from Basicmicro (formerly Ion Motion Control) can control a pair of brushed DC motors using USB serial, TTL serial, RS-232...

This version is item #5344 with soldered header pins, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. It...

The RoboClaw motor controllers from Basicmicro can control a pair of brushed DC motors using USB serial, TTL serial, RC, or analog inputs. Integrated dual...

This version is item #5346 with soldered header pins, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. It...