Search results for: 'battery holder with switch'
3x AA Battery box (JST-PH, Switch)
Brand: Core Electronics
Conveniently power your projects with this sleek, quality battery box!
$1.80 AUD, inc GST
Single CR2032 / 20mm Coin Cell Battery Holder with Switch
Brand: Adafruit
This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds one 20mm coin cell (also known as CR2032) in series to generate 3V nominal. 20mm coin cells are popular as they are used in keychain lights and remotes, so they are easy to get and fairly low cost. They tend to have about 220mAh capacity.
$2.10 AUD, inc GST
4x AA Battery box (JST-PH, Switch)
Brand: Core Electronics
Conveniently power your projects with this sleek, quality battery box!
$2.80 AUD, inc GST
2x AA Battery box (JST-PH, Switch)
Brand: Core Electronics
Conveniently power your projects with this sleek, quality battery box!
$1.60 AUD, inc GST
4 x AA Battery Holder with On/Off Switch
Brand: Adafruit
Make a nice portable power pack with this 4 x AA battery holder. It fits any alkaline or rechargeable AA batteries in series. There's a snap on cover and an on/off...
$7.70 AUD, inc GST
9V battery holder with switch & 5.5mm/2.1mm plug
Brand: Adafruit
This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm center-positive barrel plug. Use this to battery-power your Arduino (or other electronic...
$8.75 AUD, inc GST
Coin Cell Battery Holder - 2xCR2032 (Enclosed)
Brand: Sparkfun
This is a simple coin cell battery holder that can enclose two CR2032 batteries inside itself, and kept closed via two phillips head screws. Each battery holder will run batteries in series, output up to 6V, and is equipped with an On/Off slide switch and two 6" power wires (one positive and one negative) on the back.
$3.85 AUD, inc GST
Battery Holder 4xAA with Cover and Switch
Brand: Sparkfun
This 4xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.
$5.40 AUD, inc GST
LilyPad Coin Cell Battery Holder - Switched - 20mm
Brand: Sparkfun
Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull the battery, or maybe you’ve even sewn a LilyPad slide switch in-line. Wouldn’t it be nice if there was just a switch on the battery? Well, look no further.
$4.15 AUD, inc GST
4xAA battery holder (square with cover)
Brand: DFRobot
Simple 4 Cell AA Battery holder with 5" tinned leads, square configuration. This holder features a sliding, removable cover as well as an ON/OFF switch which can be used to control power to your project.
$2.60 AUD, inc GST
3x AA Battery Box (micro-USB, Switch)
Brand: Core Electronics
Conveniently power up your Pico or micro:bit using their micro-USB input
$4.50 AUD, inc GST
3x AAA Battery box (Dupont, Switch)
Brand: Core Electronics
Conveniently power your projects with this sleek, quality battery box!
$1.70 AUD, inc GST
2x AAA Battery box (JST-PH, Switch)
Brand: Core Electronics
Conveniently power your projects with this sleek, quality battery box!
$1.50 AUD, inc GST
Battery Holder 2xAA with Cover and Switch
Brand: Sparkfun
This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.
$3.85 AUD, inc GST
8 x AA battery holder with 5.5mm/2.1mm Plug and On/Off Switch
Brand: Adafruit
Make a portable power brick with plenty of juice! Use Alkaline AA's for a 12V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 9.6V supply. Either one...
$16.90 AUD, inc GST
3x AA Battery Holder with On/Off Switch and 2-Pin JST
Brand: Adafruit
Here's another addition to the growing family of AA battery holders. Behold! A holder for three (3) AA batteries! It's got a 6" long genuine JST-PH 2-pin cable connector, an On/Off switch, and, oh yes, it's in classy Adafruit black.
$7.95 AUD, inc GST
3 x AAA Battery Holder with On/Off Switch and 2-Pin JST-PH
Brand: Adafruit
This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is slim, and 3 AAA's add...
$5.40 AUD, inc GST
2 x 2032 Coin Cell Battery Holder - 6V output with On/Off switch
Brand: Adafruit
This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most popular size) in series to generate...
$4.10 AUD, inc GST
2 x CR2032 Coin Cell Battery Box w/ On-Off Switch & Plain Wires
Brand: Adafruit
This adorable little coin cell battery holder is great for small, portable, or wearable projects. It holds two 20mm coin cell batteries (also known as CR2032) in series to generate 6V nominal. 20mm coin cells are popular as they are used in keychain lights and remotes, so they are easy to get and fairly low-cost. They tend to have about 220mAh capacity.
$3.40 AUD, inc GST
3xAA Battery Holder
Brand: DFRobot
This battery holder is used to hold 3 zinc-manganese batteries (non-rechargeable) or 3 NiMH / NiCd batteries, which can change into a 4.5V battery pack from the...
$2.40 AUD, inc GST
6-AA Battery Holder, Enclosed with Switch
Brand: Pololu
Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also...
$14.20 AUD, inc GST
3-AAA Battery Holder, Enclosed with Switch
Brand: Pololu
Enclosed battery holder for three AAA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder’s leads.
$8.70 AUD, inc GST
Battery Holder 3xAA with Cover and Switch
Brand: Sparkfun
This 3xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.
$5.90 AUD, inc GST
2 x AAA Battery Holder with On/Off Switch & JST PH Connector
Brand: Adafruit
This battery holder connects 2 AAA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is nicely slim, and 2 AAA's...
$4.65 AUD, inc GST
4×AA Battery Holder (with Power Switch, DC2.1 Jack, and Cover)
Brand: DFRobot
This battery holder can hold 4 AA batteries and comes with a DC 2.1 jack that offers a simpler and more secure wire connection...
$3.90 AUD, inc GST
4-AA Battery Holder, Enclosed with Switch
Brand: Pololu
Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder’s leads.
$12.70 AUD, inc GST
3-AA Battery Holder, Enclosed with Switch
Brand: Pololu
Enclosed battery holder for three AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder’s leads.
$9.60 AUD, inc GST
Battery Holder - 2xAAA with Cover and Switch
Brand: Sparkfun
This 2xAAA battery holder puts a nice finishing touch on your battery-powered project. This holder features a sliding, removable cover as well as an ON/OFF switch...
$3.20 AUD, inc GST
2 x AA Battery Holder with On/Off Switch & JST PH Connector
Brand: Adafruit
This battery holder connects 2 AA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is fairly slim, and 2 AA's...
$5.50 AUD, inc GST
Battery Holder 2xAA with Cover and Switch - JST-XH Connector
Brand: Sparkfun
This 2xAA battery holder puts a nice finishing touch on your battery powered project. This holder features a removable, sliding cover, which is secured with a small Phillips head screw. Another bonus is the ON/OFF switch which can be used to control power to your project.
$3.80 AUD, inc GST
Battery Holder 3xAA with Cover and Switch - JST Connector
Brand: Sparkfun
This 3xAA battery holder with JST connector puts a nice finishing touch on your battery powered project...
$5.10 AUD, inc GST
Waterproof 2xAA Battery Holder with On/Off Switch
Brand: Adafruit
Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The...
$9.40 AUD, inc GST
3 x AA Battery Holder with On/Off Switch, JST, and Belt Clip
Brand: Adafruit
This battery holder connects 3 AA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is compact, and 3 AA's add...
$8.50 AUD, inc GST
3 x AAA Battery Holder with On/Off Switch, JST, and Belt Clip
Brand: Adafruit
This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is slim, and 3 AAA's add...
$7.60 AUD, inc GST
4 x AA Battery Holder with 2.1mm Plug and On/Off Switch
Brand: Adafruit
Here's another addition to Adafruit's growing family of AA battery holders. Behold! A holder for four (4) AA batteries! It's got a 5" long power cable with a 5.5/2.1mm...
$10.40 AUD, inc GST
Waterproof 3xAA Battery Holder with On/Off Switch
Brand: Adafruit
Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The...
$11.40 AUD, inc GST
3x AAA Battery Holder with Switch - Tiny FX Compatible
Brand: Pimoroni
Power your Tiny FX projects with this 3x AAA battery holder featuring a built-in power switch, JST-SUR connector, and 3.3-4.5V output range for reliable portable power.
$6.30 AUD, inc GST
Battery Holder - 1x18650 (wire leads)
Brand: Sparkfun
This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fair since that is what they have been primarily used for. However, with this battery holder you will gain the ability to incorporate 18650 cells into applications like robotics or prototyping by simply dropping one into this device and attaching the leads, that’s it.
$2.65 AUD, inc GST
3 x 18650 Battery Holder with DC2.1 Power Jack
Brand: DFRobot
The 18650 lithium battery is a commonly used lithium battery in electronic products. It is often used in batteries of laptop computers and power banks. 18650, which...
$4.35 AUD, inc GST
2 x 18650 Battery Holder with DC2.1 Power Jack
Brand: DFRobot
The 18650 lithium battery is a commonly used lithium battery in electronic products. It is often used in batteries of laptop computers and power banks. 18650, which...
$3.35 AUD, inc GST
Makers love reviews as much as you do, please follow this link to review the products you have purchased.