Search results for: '5v dc power supply'

Get your prototype online faster with a premade power supply module that can be powered by a DC Adaptor. Switchable 3.3V/5V rails and 5V USB output to cater for almost all common digital designs

A versatile power supply DC-DC converter module that offers a wide range for both input voltage (4V-35V) and output voltage (1.23V-30V). Tabs on each side allow for the input / output leads to be easily soldered on.

5V DC 4A Switchmode Plugpack Supplied with a fixed positive to tip 2.1mm DC jack. Compact design with high current regulated output. Energy authority approved. MEPS approved.

This is a DC-DC buck-mode power module, with input voltage range 8V~28V and fixed output voltage/current 5V/3A. Its work frequency can reach to 0.5MHz. The module...

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V. The board measures only 0.7″ × 0.8″, but it allows a typical continuous output current of up to 5 A. Typical efficiencies of 85% to 95% make this regulator well suited for high-power applications like powering motors or servos. High efficiencies are maintained at light loads by dynamically changing the switching frequency, and an optional shutdown pin enables a low-power state with a current draw of a few hundred microamps.

Your power supply problems just got SOLVED! This little circuit board may look tiny but inside is a high efficiency DC/DC step-down converter which can output up...

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.

This is a high grade DC Buck converter that inputs 6 to 12V and outputs 5V up to 3A or 15W. With good thermal performance and protection, this DC block is...

This Power Module is a small size 5A 350KHz 25V Buck DC to DC Converter.It can convert any DC voltage between 3.6V-25V to a selectable voltage from 3.3V to 25V. You can choose 5V direct output voltage with the switch or adjust the output voltage by the blue&white resistor.

This compact (0.45″×0.6″) U1V11F5 switching step-up (or boost) voltage regulator efficiently generates 5 V from input voltages as low as 0.5 V. Unlike most boost regulators, the U1V11F5 offers a true shutdown option that turns off power to the load, and it automatically switches to a linear down-regulation mode when the input voltage exceeds the output. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.

Converts any DC voltage between 0.9V and 5V to a steady 5VDC. Can supply up to 600mA output current.

5V DC Switchmode Plugpack Supplied with a fixed positive to tip 2.1mm DC jack. Compact design with high current regulated output. Energy authority approved. MEPS approved. 5V DC @ 2A Dimensions: 75L x 42W x 40D mm

Uninterruptible Power Supply (UPS) Module, Supports charging And Power output at the same time, 3S & 5V 5A Output...

The S7V7F5 switching step-up/step-down regulator efficiently produces 5 V from input voltages between 2.7 V and 11.8 V. Its ability to convert both higher and lower input voltages makes it useful for applications where the power supply voltage can vary greatly, as with batteries that start above but discharge below 5 V. The very compact (0.35″ × 0.475″) module has a typical efficiency of over 90% and can supply up to 1 A when stepping down and about 500 mA when stepping up.

These switchmode plugpack adaptors are slim in size, lightweight, and feature manually selectable variable voltage outputs

This DC-DC boost power supply module steps up any input voltage from 2.5V~VOUT to the output voltage of 5V/8V/9V/12V(default to 12V) at a conversion...

Note 1: Minimum input voltage is subject to dropout voltage considerations; see the dropout voltage section of product pages for more information...

DP712 is a type of single channel (50V/3A)Programmable Linear DC Power Supply with high performance

This power module provides regulated, galvanically isolated DC-to-DC power. It is set to 5 V out by default, and it can output up to 200 mA from input...