JST connectors are a very common electrical connection type that are available in a variety of sizes and families. Grab a kit and make your own cables!
These shrouded, 2-pin JST XH-style male connectors have right-angle leads and match the female connector on the 2-pin female XH-style cable, and they also work with other many other 0.1″-pitch female connectors, such as Pololu's female premium jumper wires. They are sold in packs of four units.
These shrouded, 2-pin JST XH-style male connectors have straight leads and match the female connector on the 2-pin female XH-style cable, and they also work with other many other 0.1″-pitch female connectors, such as Pololu's female premium jumper wires. They are sold in packs of four units.
This is a 2-pin JST RCY connector typically used for low-voltage applications running 10A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins to connect them both. The pins crimp to your cable and are inserted into the housing.
This JST RCY plug is also referred to as a BEC (battery eliminator circuit) connector and is commonly used with battery packs for RC applications. The connector is keyed so that power cannot be reversed. You can use a crimping tool to attach these connectors to your own 22- to 28-AWG wires. This pack contains enough housings and crimp pins (including two spare pins) for 3 male connectors.
This JST RCY plug is also referred to as a BEC (battery eliminator circuit) connector and is commonly used with battery packs for RC applications. The connector is keyed so that power cannot be reversed. You can use a crimping tool to attach these connectors to your own 22- to 28-AWG wires. This pack contains enough housings and crimp pins (including two spare pins) for 3 female connectors.
This cable will make it super easy to use our plug-and-play STEMMA QT boards and controllers with chips, breakouts, and other devices that are I2C compatible but don't come with a STEMMA QT socket already on 'em.
A simple 2-pin connector that is compatible with the "JST PH 2-pin" connector - perfect for soldering to the bottom of Adafruit's 3.3V Logic Trinket and 5V Logic Trinket!...
This 6" (15cm) cable has two 26AWG conductors with a 2.5mm-pitch 2-pin female JST XH-style connector. The spacing is very close to 0.1", which means this connector will work with 0.1" male header pins and standard perfboards and solderless breadboards. The other ends of the wires are unterminated; they can be cut to length to match your application. The red and black wires are twisted together to reduce noise.
This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based device’s pins.
If you're a DIY enthusiast who likes to micro-manage your project's connections, here is a 10-pack of some micro JST SH connectors! They're solid plastic with 4...
This cable is a little over 100mm / 4" long and fitted with JST-PH 3-pin connectors on either end. Adafruit dig the solid and compact nature of these connectors and the .. read more
This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared...
For a really long time Adafruit assumed that the JST PH didn't have a free-hanging male header version. But then Adafruit found this JST-PH 2-pin Male Cable, and Adafruit were like...
This is a 5-pin JST-ZHR cable that's terminated on the end with breadboard breadboard compatible Dupont connectors. It's the same cable that comes with our SPS30...
This is a 4-pin JST-ZHR cable that's terminated on the end with breadboard compatible Dupont connectors. The four male pins that terminate one side of the cable...
This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...
Totally 220 pieces, this JST-PH Connector Kit is a must-have for your workstation. You'll have enough sockets and plugs to fuel your maker tendencies for days on...
Totaling 560 pieces, this JST-XH Connector Kit is a must-have for your workstation. You'll have enough sockets and headers to fuel your maker tendencies for days...
Please continue if you would like to leave feedback for any of these topics:
Website features/issues
Content errors/improvements
Missing products/categories
Product assignments to categories
Search results relevance
For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.
Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.
Makers love reviews as much as you do, please follow this link to review the products you have purchased.