Search results for: 'sma bulkhead'

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8") long and has a 50Ω impedance that can handle frequencies up to 17 GHz. The SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections.

This is a basic SMA male to female connector cable at 25cm in length and RG174 housing...

This RF adapter bit is great for anyone doing RF work. Depending on the dev-board and antenna you have, you may be faced with either RP-SMA or SMA connectors. Unfortunately...

Normal GPS antennas are optimized for the US based GPS reception which is great but with more and more modules capable of tracking additional constellations (termed...

This is a 300mm (1 foot) Male TNC to Male SMA cable with injection molded stress-relief boots...

This 10m (33') SMA extension does a great job of connecting your receiver or radio to a distant antenna with as little RF loss as possible...

This SMA to U.FL Cable is commonly used to attach WiFi, Bluetooth, or nRFxxx based devices to a 2.4GHz antenna. What makes this unassuming cable special is...

This gold-plated IPEX to SMA female connector can be widely used in WiFi, GPS, 4G, 5G and other modules...

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration.

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection.

This adapter has a standard polarity Male SMA connection at both ends. It allows you to convert a standard polarity Female SMA connection to Male. You c...

The 20cm IPEX4 to SMA Adapter Cable is designed for LattePanda SBCs wireless communication. Features high-quality, stable signal transmission and...

SMA to I-PEX Cable for LoRa Antennas...

A 433MHz antenna that utilizes an SMA connector and is 200mm long with a gain of 2dBi...

This is a 10 meter (33 ft) long Male TNC to Male SMA cable with injection molded stress-relief boots...

This is a great connector for anyone doing RF work, when a straight SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground.

This is a great connector for anyone doing RF work, when a right angle SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground.

When experimenting with GPS or RF it can be very handy to have the antenna on the top of your house or car with a clear view of the sky while you stay in d...

This is a basic SMA male to female connector cable at 1M in length and RG174 housing...

This SMA male to male is a quality cable able to handle 6GHz with very low attenuation. It is the perfect cable to connect the RF Explorer Signal Generator...

Embedded antenna for small, mobile applications. Basic unpackaged antenna with LNA. 5inch cable terminated with standard male SMA connector. Match it with any SMA interface cable to create a truly small GPS prototype!

All RF connectors wear with use. The RF Explorer SMA ports are subject to minimal wear each time the connector interface is coupled and de-coupled with...

This RF connector is ideal to use RF Explorer deployed horizontally, with any antenna connected onto it. For instance when you are on the road and you...

RF cables are required when connecting RF Explorer to other instruments or devices. This 50cm cable is good for any frequency up to 3GHz, and can fit RF...

This SMA male to female is a quality cable able to handle 6GHz with very low attenuation. It is the perfect cable to connect the RF Explorer Signal Generator...

This connector cable interfaces N type female to RP-SMA male. Primarily used to connect our larger 915MHz LoRa antenna to RP-SMA connections but can be used on other...

The RockBLOCK 9704 by Ground Control is a breakout board for the new Iridium 9704 including a SMA connector and a supercap charger to enable low power...