Search results for: 'raspberry pi 5 27w power supply'

The official Power Supply needed for the micro-USB based Raspberry Pi boards.

The official Power Supply needed for the Raspberry Pi 4 Model B

The Raspberry Pi 3 Model B is the most power hungry platform released to-date and requires a 5.1V 2.5A power source. This is the official power supply by the Raspberry Pi Foundation and is suitable for use with all Raspberry Pi Models, including the latest Pi 3.

The official Power Supply needed for the Raspberry Pi 4 Model B

The PoE HAT (G) is an IEEE 802.3af/at-compliant PoE (Power Over Ethernet) HAT for Raspberry Pi 5. By using with a PoE router or switch that supports the IEEE 802.3af/at network standard, it is possible to provide both network connection and power supply for your Raspberry Pi in only one Ethernet cable.

This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.

Note 1: Minimum input voltage is subject to dropout voltage considerations; see the dropout voltage section of product pages for more information...

Converts any DC voltage between 0.9V and 5V to a steady 5VDC. Can supply up to 600mA output current.

This Power Module is a small size 5A 350KHz 25V Buck DC to DC Converter.It can convert any DC voltage between 3.6V-25V to a selectable voltage from 3.3V to 25V. You can choose 5V direct output voltage with the switch or adjust the output voltage by the blue&white resistor.

The S7V7F5 switching step-up/step-down regulator efficiently produces 5 V from input voltages between 2.7 V and 11.8 V. Its ability to convert both higher and lower input voltages makes it useful for applications where the power supply voltage can vary greatly, as with batteries that start above but discharge below 5 V. The very compact (0.35″ × 0.475″) module has a typical efficiency of over 90% and can supply up to 1 A when stepping down and about 500 mA when stepping up.

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V. The board measures...

Uninterruptible Power Supply (UPS) Module, Supports charging And Power output at the same time, 3S & 5V 5A Output...

These switchmode plugpack adaptors are slim in size, lightweight, and feature manually selectable variable voltage outputs

Note 1: Minimum input voltage is subject to dropout voltage considerations; see the dropout voltage section of product pages for more information...

This powerful synchronous switching boost regulator efficiently generates an output voltage of 5 V from an input voltage as low as 2.9 V while using an...

DP712 is a type of single channel (50V/3A)Programmable Linear DC Power Supply with high performance

24V DC 2A switch mode plug pack...

Super-compact regulated power supply. Supplied with 2.1mm DC jack. Output - 24V DC @ 3.75A

The compact (0.4″ × 0.5″) D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 85% and 90% and has a very low dropout, so it can be used with input voltages as low as a few hundred millivolts above 5 V. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.

This is a DC-DC buck-mode power module, with input voltage range 5.5~28V and fixed output voltage/current 3.3V/3A. Its work frequency can reach to 0.5MHz. The module...

This is a simple 48W (8V DC, 6A) power supply, designed for use with the Raspberry Pi Build HAT...

These switchmode plugpack adaptors are slim in size, lightweight, and feature manually selectable variable voltage outputs. All are MEPS compliant and come supplied with 7 plugs and a USB output socket.

With a rated output of 50W at 5V DC. This range of switchmode power supplies offer high efficiency DC power in a compact enclosure….

4-channel current, voltage and power monitoring HAT for Raspberry Pi with I2C interface and 0–26V range.

Looking for a high-current motor driver for your Raspberry Pi? How does dual 10A channels sound?! Cytron's latest motor driver is designed for the...

This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors. High efficiencies are maintained at light loads by dynamically changing the switching frequency, and an optional shutdown pin enables a low-power state with a current draw of a few hundred microamps.

This is a waterproof DC-DC converter. With 8-40V DC input, it converts to 12V 6A which is an ideal supply for embedded PC and robot power.

When your Raspberry Pi project requires multiple power supplies, why not check out the new Zero2Go Omini? This multi-input power supply buck-boost converter fits...

Ah the venerable 7805, who amongst Adafruit has not used this popular linear regulator? This big chunky regulator will help you get your 7-35V battery or wall adapter...