Search results for: 'probe'

These needle tipped multimeter probes are great for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Not only can these make a good replacement for any multimeter probes you have now that are damaged or worn, but thanks to the needle tip, these probes are great for testing your SMD components! Each pair of cables come in standard red/black colors with caps to protect the needle tip leads.

The Pogo Pin Probe Clip with 6 pins in a 2.54 / 0.1" pitch spacing is a great way to test and connect with pin-point accuracy without soldering!...

Includes 2 leads which are ready to accept a range of screw-on fittings. Set includes: 4 x Croc Clips 2 x Pin Plugs 2 x Hand Probes 4 x Banana Plugs 2 x Fork Connectors

DFRobot Gravity: Analog pH meter pro V2 is specifically designed to measure the pH of the solution and reflect the acidity or alkalinity. It is commonly used in...

This is an Arduino-compatible TDS sensor/Meter Kit for measuring TDS value of the water, to reflect the cleanliness of the water. It can be applied to domestic water...

Need something to sense distance, but you're expecting things to get a bit wet? Well look no further! This sensor can stretch all the way out to 4.5m in ideal conditions, with a resolution of 0.5cm...

Economical replacement test leads. Quality banana to various ends to suit most multimeters and test equipment. Banana to IC Test Clip

These SMD IC Single Hook Clip Grabbers have a small metal clip which is under spring tension that extends when squeezed. This allows them to be attached to SMD type devices quite easily. There is a round termination hole on the back of the grabber to insert a banana plug or multimeter probe.

Professional quality silicone leads with angled shrouded banana plugs to pin probes. Cat III rating: 1000V Cat IV: 600V Maximum current: 10A

Thermocouples are best used for measuring temperatures that can go above 100°C. This is a bare wires stainless-steel tip probe which can measure air or surface temperatures...

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage them or mishandle them.

Test lead set featuring a spring loaded hook connection for reliable & accurate hands free testing. Clips detach from the included banana plug leads. Cat III 1000V. Sold in black & red pair. Requires P 0414 leads for DMM connection.

Toss away your boring old SWD/JTAG adapters! This Black Magic Probe, designed by 1BitSquared with Black Sphere Technologies, is a next-generation debugging tool...

The Pogo Pin Probe Clip is a great way to test and connect with pin-point accuracy without soldering! It's sort of like an alligator clip with a built in springy...

Replacement Test Probes for your Saleae Logic!

This is a stainless steel, Type-K Thermocouple probe. A thermocouple works by taking two wires made of dissimilar metals, connecting them at the two ends, and making a temperature gradient between one end and the other (a ‘hot’ end and a ‘cold’ one). Once this is achieved, a voltage potential is formed and current flows. One junction is held in the environment where the temperature of interest exists, this is known as the hot junction. The other junction, referred to as the cold junction, can typically be found in ICs that specialize in reading the temperatures detected by the thermocouple probe.

Connect this to that without soldering using these small alligator clip test leads. 18" long cables with color-coded alligator clips on both ends. You get 6 pieces...

The Industrial soil sensor provides precise measurements of soil nitrogen, phosphorus, and potassium. Data is relayed via the MODBUS-RTU protocol on RS485...

The Pogo Pin Probe Clip with 2x5 0.05" pitch SWD spacing is a great way to test and connect with pin-point accuracy without soldering! It's sort...

Kelvin clips are used whenever you need to get a measurement right at the contact points of a circuit or component. Even though these are grippy clips, each side...

Superb construction for long life. Soft silicon rubber sheath & handles. Cat 2 1KV 10A approved.

DFRobot Gravity: analog electrical conductivity meter V2 is specially used to measure the electrical conductivity of aqueous solution, and then to evaluate the water quality, which is often used in water culture, aquaculture, environmental water detection and other fields. You may also check Liquid Sensor Selection Guide to get better familar with our liquid sensor series.

These SMD IC Single Hook Clip Grabbers have a small metal clip which is under spring tension that extends when squeezed. This allows them to be attached to SMD type devices quite easily. There is a round termination hole on the back of the grabber to insert a banana plug or multimeter probe.

This Gravity: Analog Electrical Conductivity Sensor PRO (K=1) has greatly improved the probe endurance, which allows it to offer 24/7 service for...

As an upgraded version of industrial Gravity: ORP Sensor Meter For Arduino, this new generation ORP probe employs platinum indicator electrode and...

Are you still looking for a low cost thermometer? Did you get one? Aha! Here it is! This is a new waterproof digital thermometer with display. It is suitable for greenhouse, fish tank, swimming pool and other application scenarios which require temperature measurement. It is completely waterproof to a depth of one meter for long time. And it can continuously work for half the year with only 2 AG13 button cell.

Jeff Probe is an open source JTAG probe based entirely off the popular black magic probe. We needed a cost effective solution for in house debugging, the ability for customization, and something we can include on test fixtures.

This SHT20 I2C temperature & humidity sensor is equipped with waterproof probe. It comes with the 4C CMOSens® SHT20 temperature & humidity sensor chip and the probe...

These 33mm (1.3") spring loaded pogo pins are great for programming and applications where you don’t always want headers soldered onto your boards. We use them for our programming jigs in production. The pins fit snugly into most standard perf board holes. Solder them just like you would normal wire. This unit has a conical pointed tip.

he GDP series enable users to safely make high-voltage measurements on floating circuit tests.

Suitable for multimeters with a temperature range.

This is the probe cable for Open workbench Logic sniffer. It has a 1×9 connector and 9 leads with tweezer-style test clips. These are the same tweezer-clips...

Designed for precise waveform measurement in high-voltage areas.

Identify those impossible to read SMD components! A handheld tweezer ‘plug in’ adaptor to suit just about any DMM. Permits on board or standalone testing of surface mount devices including resistors, capacitors, diodes, inductors etc (dependant on DMM functionality). 450mm length. Ideal for R&D, service centres, prototyping etc. Cat II 1000V 2A.

Logic Probe for MSO5000 Series Oscilloscopes. Includes cable, leads and grabber clips.

A high-impedance passive oscilloscope probe offering 150MHz bandwidth. Provides accurate signal capture and minimal circuit loading.

This is a interface cable designed for Bus Pirate V3 which can makes it easier to connect the Bus Pirate to a circuit and get hacking.

This luxurious accessory will make your Bus Pirate 5 a joy to use. This keyed and locking probe cable made of premium soft and flexible silicone-coated...