Search results for: 'linear ball bearings'

2 8mm ID x 15mm OD 1612 Series Linear Ball Bearing (45mm Length)

This linear ball bearing is sort of the opposite of the radial ball bearings you may be familiar with. Its intended to slide along an 8mm linear shaft, rather than...

2 8mm ID x 15mm OD 1612 Series Linear Ball Bearing (24mm Length)

2 12mm ID x 21mm OD 1612 Series Linear Ball Bearing (57mm Length)

2 6mm ID x 12mm OD 1612 Series Linear Ball Bearing (35mm Length)

2 12mm ID x 21mm OD 1612 Series Linear Ball Bearing (30mm Length)

These non-flanged bearings are able to mount on either side of a structural component that has a width that is divisible by eight, while.....

This 4mm ID x 10mm OD bearing is often times used in linear motion assemblies, by mounting multiple bearings in a line to support a movable.....

Make your robot or CNC move on Adafruit's Aluminum Slide Rail with this sliding linear ball-bearing platform AKA pillow block. The slider is 39mm x 36mm and has four holes...

Make your robot or CNC move on rails super fast with a linear bearing platform. The platform is 34mm x 30mm and has four holes tapped for M4 machine screws so you...

The digital servo is water-resistant and equipped with 35kg torque and 180-degree control. It boasts copper gears, dual ball bearings. It can be used to...

This little kit of parts yields some big build opportunities! The slide pack has all the necessary parts to make one

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 5.7 V, allowing for a holding torque of 4 kg-cm (55 oz-in).

This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 1 kg-cm (14 oz-in), and each phase draws 1 A at 4.5 V. This stepper motor’s flat profile (16 mm including the shaft) allows it to be used in places where more traditional stepper motors would be too bulky.

This NEMA 14-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 500 mA at 10 V, allowing for a holding torque of 1 kg-cm (14 oz-in).

This NEMA 17-size hybrid bipolar stepping motor has an integrated 38 cm (15") threaded rod as its output shaft, turning it into a linear actuator capable...

This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 2.2 kg-cm (30 oz-in), and each phase draws 1 A at 5.9 V. This stepper motor’s flat profile (21 mm including the shaft) allows it to be used in places where more traditional stepper motors would be too bulky.

This NEMA 17-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1.7 A at 2.8 V, allowing for a holding torque of 3.7 kg-cm (51 oz-in).

This NEMA 17-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1.2 A at 4 V, allowing for a holding torque of 3.2 kg-cm (44 oz-in).

This NEMA 14-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 2.7 V, allowing for a holding torque of 1.4 kg-cm (20 oz-in).

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 8.6 V, allowing for a holding torque of 14 kg-cm (190 oz-in).

This NEMA 11-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 670 mA at 3.5 V, allowing for a holding torque of 600 g-cm (8.3 oz-in).

This small NEMA 8-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 800 mA at 4.3 V, allowing for a...

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 7.4 V, allowing for a holding torque of 9 kg-cm (125 oz-in).

This NEMA 17-size pancake bipolar stepping motor from Sanyo features an integrated high-resolution (1000 P/R) quadrature encoder that allows for 4000...

This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 1.9 kg-cm (26 oz-in), and each phase draws 1 A at 5.4 V. This stepper motor’s flat profile (25.6 mm including the shaft) allows it to be used in places where more traditional stepper motors would be too bulky.

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 2 A at 4.5 V, allowing for a holding torque of 14 kg-cm (190 oz-in).

This small NEMA 8-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 600 mA at 3.9 V, allowing for a holding torque of 180 g-cm (2.5 oz-in). With a weight of 60 g, this is one of the smallest stepper motors Pololu carry.

This NEMA 17-size hybrid bipolar stepping motor has an integrated 28 cm (11″) threaded rod as its output shaft, turning it into a linear actuator capable of precision open-loop positioning. The included traveling nut has four mounting holes and moves 40 µm (1.6 mil) per full step; finer resolution can be achieved with microstepping. The stepper motor has a 1.8° step angle (200 steps/revolution) and each phase draws 1.7 A at 2.8 V, allowing for a holding torque of 3.7 kg-cm (51 oz-in).

This NEMA 17-size pancake bipolar stepping motor from Sanyo features an integrated high-resolution (1000 P/R) quadrature encoder that allows for 4000...

This version of the FS5115M high-torque servo from FEETECH is specially modified to provide access to the feedback potentiometer through a fourth (green)...

This NEMA 14-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 280 mA at 7.4 V, allowing for a holding torque of 650 g-cm (9 oz-in).

This NEMA 23-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 2.8 A at 2.5 V, allowing for a holding torque of 13 kg-cm (180 oz-in).