Search results for: 'hex nuts'

Standard hex nuts have a lower profile compared to nylon-insert locknuts and are perfect for use as a jam nut.

This M3 hex nut is made from steel, is zinc-plated, and comes in packs of 25.

This M2.5 hex nut is made from steel, is zinc-plated, and comes in packs of 25...

This is an M3 Hex nut for use with M3 screws...

Totaling 420 pieces, this M3 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end!

This #4-40 hex nut is made from steel, is zinc-plated, and comes in packs of 25.

Totaling 420 pieces, this White Nylon M2.5 Screw Set is a must-have smörgåsbord for your workstation. You'll have more than enough screws, nuts, and hex standoffs...

This panel mount extension cable will allow you to extend an HDMI connection and secure it to an enclosure. Perfect for placing your Raspberry Pi in a secure box...

This #2-56 hex nut is made from steel, is zinc-plated, and comes in packs of 25.

The Kitronik Prong soil moisture sensor for BBC microbit is a sensor board that can be directly mounted to a BBC micro:bit to monitor moisture present in soil.

Totaling 380 pieces, this M2.5 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for...

These locknuts have a nylon insert that the threads of a mating.....

Finally Adafruit get Adafruit's very own super sweet sixteen... 16 millimeters that is! Adafruit's Black Plated M/F Brass 16mm Standoffs are engineered specifically to keep your PiTFT...

If you have a computer or tablet or device with Mini HDMI output but you want to connect it to a projector, monitor or display with VGA input, you have come to the...

Though most servos support their splined output shafts with internal bearings, those bearings can’t handle many of the radial loads they.....

This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and forth constantly. Deciding...

What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more like Tip-Ring-Sleeve. This nifty, gold-plated connector is known by many...

Here is the perfect kit with two faceplate options for your MagTag, including a vivid Red Arrow plate and a dreamy white Cloud plate. And of course, the mounting hardware is included, so you can assemble it with just a plain Phillips screwdriver. Takes less than 3 minutes!

This or that, one or the other, perhaps or perhaps not! So hard to make decisions these days without feeling like you're just going back and forth constantly. Deciding...

This Alpha 250K Reverse Audio potentiometer is a two-in-one, good in a breadboard or with a panel. It's a unique reverse audio taper 250K ohm...

You have a stepper motor, but you need to attach it to your CNC project, eh? Not so easy if you don't have a stepper motor mount just like this fine one one here!...

This Alpha 2K Linear potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 2K ohm...

This Alpha Dual-Gang 100K Audio potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio / log tape 100K ohm...

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left...

Here is a chic minimalist enclosure for your CLUE board! This case has been laser-cut specifically to accommodate the TFT display, tactile buttons, and capacitive pads.

These aluminum gearmotor brackets let you securely mount Pololu's larger Pololu plastic gearmotors (228:1 offset, 120:1 offset, 200:1 90-degree, and 120:1 90-degree) to your project. These brackets are sold in pairs, and each bracket comes with two 1″ long and two 0.75″ long #2-56 screws for securing different size motors. Each bracket also features two mounting holes and one mounting slot intended for #4-size screws (not included).

This Alpha 5K Linear potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 5K ohm potentiometer,...

This Alpha Dual-Gang 1K Audio potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio/log taper 1K...

This Alpha 50K Linear potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 50K ohm...

This Alpha 250K Linear potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 250K ohm...

This Alpha 10K Reverse Audio potentiometer is a two-in-one, good in a breadboard or with a panel. It's a unique reverse...

This Alpha Dual-Gang 10K Audio potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio/log taper 10K...

This Alpha 5K Reverse Audio potentiometer is a two-in-one, good in a breadboard or with a panel. It's a unique reverse audio taper 5K ohm...

This Alpha 20K "W" TS Tone potentiometer is a two-in-one, good in a breadboard or with a panel. It's a funky W TS Tone taper 20K ohm...

This Alpha 1K Reverse Audio potentiometer is a two-in-one, good in a breadboard or with a panel. It's a unique reverse audio...

This Alpha Dual-Gang 500K Linear potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio/log...

This Alpha Dual-Gang 50K Linear potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio/log...

This Alpha Dual-Gang 5K Audio potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio/log...

This Alpha 1K Linear potentiometer is a two-in-one, good in a breadboard or with a panel. It's a fairly standard linear taper 1K ohm...

This Alpha Dual-Gang 1M Audio potentiometer is a two-in-one potentiometer stack, for independent stereo control. It's an audio/log tape 1 Megaohm...