Search results for: 'mmcx to sma'

This RF adapter cable is super handy for anyone doing RF work. Often times, small electronics save space by having a pick-and-placeable u.FL connector (also called...

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection.

This is an inner thread (outer nut) adapter that will connect to any of our wireless boards or interface cables and allow you to use an antenna/cable that has an outer thread configuration.

The 20cm IPEX4 to SMA Adapter Cable is designed for LattePanda SBCs wireless communication. Features high-quality, stable signal transmission and...

SMA to I-PEX Cable for LoRa Antennas...

This is a basic RP-SMA male to female connector cable at 1M in length and RG174 housing...

This is a great connector for anyone doing RF work, when a right angle SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground.

This is a great connector for anyone doing RF work, when a straight SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground.

This gold-plated IPEX to SMA male cable(inner needle) passed the 48h salt spray test, which is durable and not easy to rust, and can be widely used in...

This is a basic RP-SMA male to female connector cable at 10M in length and RG58 housing...

This is a basic RP-SMA male to female connector cable at 25cm in length and RG174 housing...

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection...

This 2.2"/57mm long antenna has 2dBi of gain and 50O impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter...

This is a very simple 1m long TNC to RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an equally powerful reader board...

This 2.4"/61mm long antenna has 2dBi of gain and 50O impedance so it will work fantastically with just about any 850/900/1800/1900/2100 wireless receiver/transmitter...

This RF adapter bit is great for anyone doing RF work. If your receiver/transmitter/transceiver has an MCX connector but you really want to tie it to an SMA antenna...

PCB edge mount - SMA RF connector. Perfect for prototyping with the GPS and Cellular devices that require an antenna connection. These connectors have a female signal pin and will correctly mate with the original SMA type antennas.

This SMA male to male is a quality cable able to handle 6GHz with very low attenuation. It is the perfect cable to connect the RF Explorer Signal Generator...

This SMA male to female is a quality cable able to handle 6GHz with very low attenuation. It is the perfect cable to connect the RF Explorer Signal Generator...

RF cables are required when connecting RF Explorer to other instruments or devices. This 50cm cable is good for any frequency up to 3GHz, and can fit RF...

This connector cable interfaces N type female to RP-SMA male. Primarily used to connect our larger 915MHz LoRa antenna to RP-SMA connections but can be used on other...

PCB edge mount Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. This is a standard edge connector. The thickness between pins is 0.063" so that it can slide sideways onto a PCB. See the mechanical drawing to create your footprint.

This is a great connector for anyone doing RF work, when a right angle RP-SMA connector is required. Solder it into your PCB for a very secure mechanical connection. You've probably seen tons of these on various development boards! The four mechanical connectors also act as the RF ground.

Designed for 810-910 MHz (868MHz center frequency) this antenna is ideal for distant LoRa nodes...

N-type to SMARS Cable to connect LoRa Gateway to Fibreglass antenna and extend the coverage...

N-type to SMARS Cable to connect LoRa Gateway to Fibreglass antenna and extend the coverage...