Search results for: 'male female'

ZipWire™ provides a convenient way to connect the signals in your projects. The wires can be unzipped for individual wires as needed. The color-coding can be used to organize power, ground and other signal types to keep your circuit organized. The rainbow-colored ribbon cable provides the 10 standard electrical colors. Each ZipWire ribbon provides 40 wires, four of each color.

Unplugging USB devices just to remove power is a thing of the past with this handy little microUSB extender.

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers form Pimoroni might be just what you need...

This RF adapter bit is great for anyone doing RF work. Depending on the dev-board and antenna you have, you may be faced with either RP-SMA or SMA connectors. Unfortunately...

This is a basic SMA (Sub-Miniature A) male to female connector cable. Each cable is 25cm (9.8") long and has a 50Ω impedance that can handle frequencies up to 17 GHz. The SMA connectors at each end are small enough for most consumer GPS, cellular, and other RF applications and they use a threaded housing to create strong mechanical connections.

This is a basic SMA male to female connector cable at 25cm in length and RG174 housing...

This handy USB extension cable will make it easy for you to enclose a device that has a A type (USB host) port. We think this would be most handy when putting a...

This is an adapter that converts an RP-SMA board to an SMA antenna. The adapter will connect to any of our 2.4GHz wireless boards (Bluetooth, Nordic, or XBee) or interface cables and will allow you to use an antenna/cable with an SMA connection.

A USB 2.0 extension cable designed to achieve distances up to 5m

USB Type-C Male To USB-A Female Adapter...

This is a basic RP-SMA male to female connector cable at 1M in length and RG174 housing...

This connector pack comes with five 3.5mm (MH-FC) bullet connectors and five 3.5mm (MH-FC) connectors. These are the same connectors as.....

This 10m (33') SMA extension does a great job of connecting your receiver or radio to a distant antenna with as little RF loss as possible...

This Adapter allows you to run devices and cables with the classic USB Type A connector off a device or adapter with a USB Type C port...

This is a 2-pin JST RCY connector typically used for low-voltage applications running 10A or less. They are commonly found in RC vehicles. These come in a bag of 1 male plug, 1 female plug, plus pins to connect them both. The pins crimp to your cable and are inserted into the housing.

These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of this generic XT60 prevents reverse polarity, and when plugged in the connection is super-solid. Perfect for applications up to 65A continuous draw. Sold in pairs of 1 male and 1 female connector.

Type-C extension cable specially selected for Unihiker, suitable for compact project production...

N-type to SMARS Cable to connect LoRa Gateway to Fibreglass antenna and extend the coverage...

This is a basic SMA male to female connector cable at 1M in length and RG174 housing...

This M12 to RJ45 Ethernet adapter uses M12 male 4 pin D coded with IP67 waterproof rating, which is impervious to dust and short-term soaking, safe and...

This Male-to-Female 8mm REX™ CV Joint offers positive drive at variable angles. A constant-velocity (CV) joint allows you to create a drive.....

This DB9 Male to RJ45 Female Adapter can be used to handle serial data communication between RS232 devices with one RJ45 network cable, or as an extender...

This is a basic RP-SMA male to female connector cable at 25cm in length and RG174 housing...

This is a basic RP-SMA male to female connector cable at 10M in length and RG58 housing...

These are generic connectors similar to the popular Deans Ultra Plug connectors. They are sold as matching male-female pairs and have a current rating of 50 A. They are the smallest high-current connectors Pololu know of, and they are great for projects that involve bigger motors and controllers, such as Pololu's Simple Motor Controllers and high-power motor drivers.

These sew-on fabric snaps are the same size used on the LilyPad SimpleSnap boards. You can sew these into your project to allow for easy removal or prototyping. They are 8mm snaps, which is equivalent to a size #1/0 at your local fabric shop.

These are high-current XT60 connectors commonly used in the RC hobby industry. They are sold as matching male-female pairs and are great for projects that involve bigger motors and controllers, such as Pololu's high-power motor drivers and Simple Motor Controllers.

These are high-current XT60 connectors commonly used in the RC hobby industry. They are sold as matching male-female pairs and are great for projects that involve bigger motors and controllers, such as Pololu's high-power motor drivers and Simple Motor Controllers.

RF cables are required when connecting RF Explorer to other instruments or devices. This 50cm cable is good for any frequency up to 3GHz, and can fit RF...

This DB15 Male to RJ45 Female Adapter can be used to handle data communication between VGA devices with one RJ45 network cable, or as an extender to...

N-type to SMARS Cable to connect LoRa Gateway to Fibreglass antenna and extend the coverage...

This product includes a pair in-line power wire connectors. If you have a project where you'd like to be able to detach the wiring, this wire will fit the bill. Its a JST 2.5mm 'free hanging' cable assembly that latches strongly.

This pack contains everything you need to add up to three male JR connectors — the connectors that mate with those commonly found on generic RC servos — to custom cables. You can use a crimping tool to attach the included pins to your own 22–26 AWG wires. This pack contains enough housings and crimp pins (including 3 spare pins) for 3 male connectors. The crimp pins have gold-flashed male contacts.

This 24-inch (600-mm), twisted cable can be used to extend the leads of many common RC hobby servos. It has 22-AWG wires, and both the male and female cable ends are compatible with both JR- and Futaba-style connectors, allowing it to work in either system or as an adapter between systems. The cable’s conductors each consist of 60 strands, making it much more flexible than standard servo cables, and the wires are twisted to reduce electromagnetic interference (EMI).

This 12-inch (300-mm), flat cable can be used to extend the leads of many common RC hobby servos. It has 22-AWG wires, and both the male and female cable ends are compatible with both JR- and Futaba-style connectors, allowing it to work in either system or as an adapter between systems. The cable’s conductors each consist of 60 strands, making it more flexible than standard servo cables.