Search results for: 'flexible coupler'

This 6" (15cm) cable has two 26AWG conductors with a 2.5mm-pitch 2-pin female JST XH-style connector. The spacing is very close to 0.1", which means this connector will work with 0.1" male header pins and standard perfboards and solderless breadboards. The other ends of the wires are unterminated; they can be cut to length to match your application. The red and black wires are twisted together to reduce noise.

This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and female connectors on the other. The cable insulation is...

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection.

The Qwiic to STEMMA Adapter Cable allows interoperability between the SparkFun Qwiic Connect System and the I2C based STEMMA boards from Adafruit...

Type-C extension cable specially selected for Unihiker, suitable for compact project production...

This 6mm D-Bore to 6mm D-Bore Hyper Coupler is a strong, compact, balanced way to couple two shafts together. As with all ‘Hyper’ parts,.....

This SMA male to male is a quality cable able to handle 6GHz with very low attenuation. It is the perfect cable to connect the RF Explorer Signal Generator...

This 12-inch (300-mm), flat Y-cable is typically used to connect two servos to a single servo port . It has 22-AWG wires terminated on one end by a “JR”-style female connector and on the other by two Futaba J male connectors, allowing it to work in either system or as an adapter between systems. The split occurs close to the cable’s JR input, so the two male ends can be separated by up to approximately 18" (450 mm). The cable’s conductors each consist of 60 strands, making it more flexible than standard servo cables.

This SMA male to female is a quality cable able to handle 6GHz with very low attenuation. It is the perfect cable to connect the RF Explorer Signal Generator...

This servo cable has a shrouded male servo connector on one end, and 3x breadboard hookup pigtails at the other end...

This 6-inch (150-mm), twisted cable has 22-AWG wires and female “JR”-style connectors on both ends, the same kind of connector commonly found on RC hobby servos. It can be used to make connections between devices with 0.1" 3-pin male headers, such as between RC servo controllers or RC receivers and motor controllers with an RC interface. It can also be a convenient way to connect various 3-pin sensors to a robot controller. The cable’s conductors each consist of 60 strands, making it much more flexible than standard servo cables, and the wires are twisted to reduce electromagnetic interference (EMI).

This 24-inch (600-mm), twisted cable can be used to extend the leads of many common RC hobby servos. It has 22-AWG wires, and both the male and female cable ends are compatible with both JR- and Futaba-style connectors, allowing it to work in either system or as an adapter between systems. The cable’s conductors each consist of 60 strands, making it much more flexible than standard servo cables, and the wires are twisted to reduce electromagnetic interference (EMI).

This 12-inch (300-mm), twisted cable has 22-AWG wires and female “JR”-style connectors on both ends, the same kind of connector commonly found on RC hobby servos. It can be used to make connections between devices with 0.1" 3-pin male headers, such as between RC servo controllers or RC receivers and motor controllers with an RC interface. It can also be a convenient way to connect various 3-pin sensors to a robot controller. The cable’s conductors each consist of 60 strands, making it much more flexible than standard servo cables, and the wires are twisted to reduce electromagnetic interference (EMI).

This 12-inch (300-mm), flat Y-cable can be used to split a single RC hobby servo signal into two identical outputs. It has 22-AWG wires terminated on all three ends by “JR”-style female connectors, which are compatible with 0.1" header bins and both male JR and male Futaba J connectors. The split occurs close to the cable’s input, so the two output ends can be separated by up to approximately 18" (450 mm). The cable’s conductors each consist of 60 strands, making it more flexible than standard servo cables.

This 12-inch (300-mm), flat cable can be used to extend the leads of many common RC hobby servos. It has 22-AWG wires, and both the male and female cable ends are compatible with both JR- and Futaba-style connectors, allowing it to work in either system or as an adapter between systems. The cable’s conductors each consist of 60 strands, making it more flexible than standard servo cables.