Shark-4 Servo Gearbox (0.56 sec/60°, 18 RPM, 1888 oz-in Torque, 630° Rotation)Feedback Mode
Available with a lead time
Expect dispatch between Dec 02 and Dec 03
Quantity Discounts:
- 3-6 $457.68 (exc GST)
- 6+ $433.60 (exc GST)
This Shark-4 Servo Gearbox is driven by the Hitec's flagship HSR-M9382TH brushless, titanium geared servo. This gearbox introduces a 4:1 external gear ratio in order to lessen the range while increasing the torque and precision four-fold. If this ratio doesn't suit your needs, be sure to check out the other Servo Gearbox options.
Having the servo mounted in the gearbox isolates the load to a steel hub-shaft that is supported in a pair of ball bearings to protect the servo from any axial loads. The gearbox opens up a world of mounting possibilities given the M4 threaded holes on each side which are on the grid pattern for compatibility throughout the goBILDA® system. The hub on the top of the gearbox provides threaded holes to fasten to, but you can also opt to fasten straight to the aluminum output gear using M4 hardware and standoffs or spacers. The 8mm REX bore of the hub-shaft can drive an 8mm REX shaft or act as a wire pass-thru.
If you’re not accustomed to using a servo gearbox, it’s just like a normal servo only larger. While the range and torque might be greater than the servos you’re used to, the control signal is identical. It will simply plug into an R/C receiver, an Arduino, Raspberry Pi, or REV controller. Furthermore, since the servo hasn’t been modified in any way, it is FTC legal!
This Servo Gearbox is available in both feedback mode, and continuous mode. In feedback mode, your signal controls the position. In continuous mode, your signal controls the speed and direction. Regardless of which you purchase, it can always be toggled to the other mode with a DPC-11 servo programmer.
How Far Will This Servo Gearbox Rotate When In Feedback Mode?
The answer to this question is partially dependant on what you are using to control the servo that drives the gearbox. A Servo Travel Tuner allows you to achieve maximum rotation, but it is just as useful to dial down the rotation to suit your needs.
With an Average Radio System:
1.125 Turns (405°)
Your average transmitter and receiver will output a relativly narrow PWM signal range.
Radio System + Travel Tuner:
1.75 Turns (630°)
Adding a Servo Travel Tuner to your radio system setup will allow you to achieve wide PWM signal ranges.
Wide Signal Controllers:
1.75 Turns (630°)
Controllers such as Arduinos, and Raspberry Pi servo hats can usually send a wide signal.
Gear Ratios
While we offer a variety of pre-made ratios, if you already own one of our Servo Gearboxes and want to change the ratio, here are the gears you will need to obtain the ratio you desire.
| Ratio | Servo Gear | Hub-Mount Gear |
|---|---|---|
| 2:1 | 40T (2305-0025-0040) | 80T (2302-0014-0080) |
| 3:1 | 30T (2305-0025-0030) | 90T (2302-0014-0090) |
| 4:1 | 24T (2305-0025-0024) | 96T (2302-0014-0096) |
| 5:1 | 20T (2305-0025-0020) | 100T (2302-0014-0100) |
| 7:1 | 15T (2305-0025-0015) | 105T (2302-0014-0105) |
| 9:1 | 12T (2305-0025-0012) | 108T (2302-0014-0108) |
Downloads
Specs
| Weight | 225g |
|---|---|
| Gear Ratio | 4:1 |
| Voltage Range | 6V - 8.4V |
| No-Load Speed (6.0V) | 0.68sec/60° (14.7 RPM) |
| No-Load Speed (7.4V) | 0.45sec/60° (17.8 RPM) |
| Stall Torque (6.0-7.4V) | 1888 oz-in (136 kg.cm) |
| No-Load Current (6.0V) | 260mA |
| No-Load Current (7.4V) | 270mA |
| Stall Current (6.0-7.4V) | 2700mA |
| Motor Type | Brushless DC |
| Direction with Increasing PWM Signal | Counter Clockwise |
| Max PWM Range | 800-2200µsec |
| Travel per µsec | 0.45°/µsec |
| Max Rotation | 630° (1.75 Turns) |
| Pulse Amplitude | 3-5V |
| Max Rotation | 1260° (3.5 Turns) |
| Deadband Width | 1 µsec |
| Wire Length | 300mm (11.81") |
| Wire Gauge | 22AWG |
| Connector Type | 3-Pos TJC8 Servo Connector [MH-FC] |
| Intellectual Property | Patented |
This product is listed in:
goBILDA>MOTION>Servos>Servo Gearboxes>Shark ClassgoBILDA>ELECTRONICS>Servos>Servo Gearboxes>Shark Class
Exact shipping can be calculated on the view cart page (no login required).
Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).
We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):
- $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
- $7+ for Standard Post (typically 6+ business days, tracked)
- $11+ for Express Post (typically 2+ business days, tracked)
- Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.
Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.
Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.
International Orders - the following rates are for New Zealand and will vary for other countries:
- $12+ for Pack and Track (3+ days, tracked)
- $16+ for Express International (2-5 days, tracked)
If you order lots of gear, the postage amount will increase based on the weight of your order.
Our physical address (here's a PDF which includes other key business details):
Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia
Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.
Have a product question? We're here to help!
Guides
The Maker Revolution
Projects
Pi Zero Motion Sensing Camera
555 Timer Step Sequencer Synthesiser
Wireless QI Phone Charger Powered by Raspberry Pi
Makers love reviews as much as you do, please follow this link to review the products you have purchased.
Product Comments