Search results for: 'lever connector mount'

What is this TRS bit? Turtle Rock Studios? Transmission Raman Spectroscopy? Not quite, more like Tip-Ring-Sleeve. This nifty, gold-plated connector is known by many...

These are simple 2-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line up with standard 0.1" perf boards.

These aluminum gearmotor brackets let you securely mount Pololu’s 25D mm metal gearmotors to your project. The brackets are sold in pairs, and each bracket includes four M3 screws for securing the motor to the bracket. Each bracket also features seven mounting holes and twelve mounting slots for M3 or #4-size screws (not included), giving you a variety of mounting options.

These shrouded, 2-pin JST XH-style male connectors have right-angle leads and match the female connector on the 2-pin female XH-style cable, and they also work with other many other 0.1″-pitch female connectors, such as Pololu's female premium jumper wires. They are sold in packs of four units.

The DINrPlate Universal is an innovative universal DIN Rail mounting solution with sliding, rotating standoffs allowing it to accommodate a wide range of...

Mount your KKSB case securely on any tripod with this 14-20 UNC thread bracket, compatible with KKSB cases for Raspberry Pi 5, Arduino, Jetson, and other single-board computers.

Pipe audio in or out of your project with this very handy panel mount audio jack. It's a mono jack with a disconnect pin so you'll get a ground sleeve pin, a left...

Screw Terminals with 5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 300V @ 8A. Terminal can accept 26 to 14AWG wire. 5mm/197mil pin pitch will line up well with standard 0.1" perf boards but the pins are thick enough (1.0mm OD) that you may need to increase the hole diameter on some perf boards.

These are simple 6-position screw terminals with 2.54mm pitch pins. Rated up to 150V @ 6A, this terminal can accept 30 to 18AWG wire. The 2.54mm pitch will line...

These are very handy. They are simple angle brackets with one threaded and unthreaded hole. Use them for connecting PCBs at 90 degree angles, mounting accelerometers, gryros, etc. They can also be used on the universal plate set for mounting all sorts of sensors and such.

This Flat Pattern Mount is able to fasten to a part which has threaded holes on the 16mm pattern, leaving the screw heads flush with the...

These Clincher connectors from Amphenol FCI can be used to terminate Flat Flexible Cables (FFCs) to an easy-to-use standard header. Simply insert the end of the...

You have a TT motor, but you need to attach it to your CNC project, eh? Not so easy if you don't have an L-Bracket DC Motor Mount just like this fine one here! Made...

This bracket was designed specifically for the Glideforce Medium-Duty (MD) linear actuators. It is made from stamped, zinc-plated steel and has been...

This pack contains everything you need to add up to three male JR connectors — the connectors that mate with those commonly found on generic RC servos — to custom cables. You can use a crimping tool to attach the included pins to your own 22–26 AWG wires. This pack contains enough housings and crimp pins (including 3 spare pins) for 3 male connectors. The crimp pins have gold-flashed male contacts.

Screw Terminals with 5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 300V @ 8A. Terminal can accept 26 to 14AWG wire. 5mm/197mil pin pitch will line up well with standard 0.1" perf boards but the pins are thick enough (1.0mm OD) that you may need to increase the hole diameter on some perf boards.

Intended for mounting plastic enclosures onto DIN rails, this DIN rail mounting bracket is an affordable way to mount 'things' to your DIN rail! For wide...

These shrouded, 5-pin JST XH-style male connectors have extended right-angle leads. They can be used with female JST XH-style connectors, and they also work with other many other 0.1″-pitch female connectors, such as Pololu's female premium jumper wires. They are sold in packs of two units.

Downloads

A 30mm Hitec Linear Servo (16.1mm/sec, 5.2kg Thrust)

A 30mm Hitec Linear Servo (7.5mm/sec, 12.4kg Thrust)

This machined aluminum bracket allows the Concentric LD series linear actuators to be mounted to a structure. Complete mounting hardware is included. Two brackets are required for mounting each actuator.

This is a high quality 2-pin screw terminal. Very useful when you want to connect 24-18AWG wires to your circuits.

"Simplicity is the ultimate sophistication" - Leonardo da Vinci This 1/4" screw to 1/4" screw is very simple but you'll find it an essential adapter for video/photo...

The servo Bit is something that we're really excited about – a controllable motor that can swing back and forth! It has two modes: in “Turn” mode, the input from other littleBits determines the position of the arm – try using a dimmer to set the angle you want. In “Swing” mode, the servo will move back and forth on its own – the input controls how fast it goes. Attach a flag to the arm to make a signaling machine!

These Clincher connectors from Amphenol FCI can be used to terminate Flat Flexible Cables (FFCs) to an easy-to-use standard header. Simply insert the end of the...

Screw Terminals with 3.5mm pitch pins. Comes in 2 or 3 positions and have the really cool feature of slide-locking together to form any size you need (4, 5, up to 20 without problems). Rated up to 125V @ 6A. Terminal can accept 30 to 20AWG wire. 3.5mm/138mil pin pitch will not fit standard 0.1" perf boards but this is the most common pitch screw terminal.

This 2501-0001-0002 Pulley Bracket is designed for use with the 2500-0014-0336 Viper Slide. This pack includes four pulley brackets and.....

This one's going out to all the makers and designers who use DIN railing in their builds. This adapter plate is perfect for simplifying complex wiring. It's pretty...

This lightweight plastic mounting plate is designed specifically for the RockBLOCK 9704 SMA, providing an easy and secure way to integrate the device...

This 48mm length control arm can be bolted to a goBILDA hub or other goBILDA component which has the 16mm square pattern. A ball linkage,...