Search results for: 'cr123a battery holder'

This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fair since that is what they have been primarily used for. However, with this battery holder you will gain the ability to incorporate 18650 cells into applications like robotics or prototyping by simply dropping one into this device and attaching the leads, that’s it.

Make a portable power brick with plenty of juice! Use Alkaline AA's for a 9V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 7.5V supply. Either one...

The 18650 lithium battery is a commonly used lithium battery in electronic products. It is often used in batteries of laptop computers and power banks. 18650, which...

This is an incredibly simple two cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fair since that is what they have been primarily used for. However, with this battery holder you will gain the ability to incorporate 18650 cells into applications like robotics or prototyping by simply dropping one into this device and attaching the leads, that’s it.

Battery holder for four AA cells arranged as two back-to-back two-cell holders.

This is a 9V battery pack with on/off switch and a pre-attached 5.5mm/2.1mm center-positive barrel plug. Use this to battery-power your Arduino (or other electronic...

Basic 20mm coin cell holder. Posts can be inserted into 0.1" perf board! Holds the common CR2032 type batteries.

This battery mount kit comes with the necessary hardware to mount a GB-14-0014 or GB-3100-0012-0020 battery to 1120 Series U-Channel or 1121 Series Low-Side U-Channel.

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is slim, and 3 AAA's add...

Battery holder for eight AA cells arranged as two back-to-back four-cell holders.

This tiny coin cell battery holder is ideal for small portable or wearable projects. It holds two 20mm coin cells (2032 are the most popular size) in series to generate...

This adorable little coin cell battery holder is great for small, portable, or wearable projects. It holds two 20mm coin cell batteries (also known as CR2032) in series to generate 6V nominal. 20mm coin cells are popular as they are used in keychain lights and remotes, so they are easy to get and fairly low-cost. They tend to have about 220mAh capacity.

Battery holder for 4 AAA cells.

Enclosed battery holder for six AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also...

This profile-matched Battery Mount provides a simple, secure way to fasten a 12V NiMH Nested Battery to your robot. Its six...

Battery holder for six AA cells arranged as two back-to-back three-cell holders.

This battery holder connects 2 AAA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is nicely slim, and 2 AAA's...

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The...

A 3xAA Battery Holder with a built-in lead that terminates in a 2.1mm DC jack, the lead and jack combined is approx. 150mm in length...

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.

This battery holder connects 2 AA batteries together in series for powering all kinds of projects. Adafruit spec'd these out because the box is fairly slim, and 2 AA's...

Enclosed battery holder for four AA cells. This holder features a lid that slides over the batteries and snaps into place to fully enclose them. It also features a switch that lets you open and close the electrical connection between the batteries and the holder’s leads.

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline cells.

Here's yet another addition to Adafruit's family of AA battery holders. It's a holder for five (5) AA batteries, with 5" wire leads. It's black and has a 2.1mm barrel plug...

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The...

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with friction. The metal housing connects to the positive side of the battery and the PCB pad underneath is connected to the negative side.