Search results for: 'alignment pins'

Connect this to that when a 22-pin FPC connector is needed. This 20 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on...

Connect this to that when an 18-pin FPC connector is needed. This 50mm long cable is made of a flexible PCB. It's A-B style which means that pin one...

Connect this to that when a 22-pin FPC connector is needed. This 5 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on...

Connect this to that when a 22-pin FPC connector is needed. This 10 cm long cable is made of a flexible PCB. It's A-B style, meaning that pin one on...

A 22-pin, 200mm flat, flexible cable with 0.5mm pitch. These cables are A-B style, so pin one on one side will match with pin one on the other side. Use...

Connect this to that when a 24-pin FPC connector is needed. This 10 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as...

Connect this to that when a 18-pin FPC connector is needed. This 25 cm long cable is made of a flexible PCB. It's A-B style which means that pin one...

A 22-pin, 100mm flat, flexible cable with 0.5mm pitch. These cables are A-B style, so pin one on one side will match with pin one on the other side. Use...

Connect this to that when a 24-pin FPC connector is needed. This 25 cm long cable is made of a flexible PCB. It's A-B style (sometimes referred to as...

A 22-pin, 50mm flat, flexible cable with 0.5mm pitch. These cables are A-B style, so pin one on one side will match with pin one on the other side. Use...

Add a stylish navigational aid to your project with our fully assembled ANO scroll wheel encoder breakout!...

With the Breadboard breakout for the BBC micro:bit you can plug a microbit into a standard 2.54mm pitch breadboard, across the center, just like a standard IC.

That new Raspberry Pi 400 computer you just got has a row of 2x20 pin headers on the right side - those are the GPIO (general purpose input/output) pins, and for those of Adafruit who like to hack electronics, they are where the real fun lies

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a 40-pin FPC to Right Angle 2x20 IDC Male Plug Header Adapter.

Here is an easy solution for extending your Raspberry Pi's GPIO capabilities. This is a 40-pin FPC to Straight 2x20 IDC Male Plug Header Adapter

These shrouded, 2-pin JST XH-style male connectors have right-angle leads and match the female connector on the 2-pin female XH-style cable, and they also work with other many other 0.1″-pitch female connectors, such as Pololu's female premium jumper wires. They are sold in packs of four units.

If you love power adapters or toys & gadgets that have magnetic connections, you can now experiment with these futuristic connectors easily. It's...

Add connectors to your micro metal gearmotors with these boards that feature side-entry, 2-pin male JST SH-type connectors. These boards are compatible...

A conveniently sized, labelled proto-board add-on for your Raspberry Pi Pico, perfect for permanently attaching your custom circuits!

This 2x20-pin strip, right-angle female header is a perfect companion piece to Adafruit's 2x20-pin Dual Male Header. It's a great way to add right-angle capability to a 2x20 pin circuit board either by attaching the right-angle male headers to the board and having a right-angle female header or connecting the female header to Adafruit's 2x20 Dual Male headers.

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for any Particle Mesh or Feather board, so that you can easily interface with Seeed's...

Beguiled by a fancy new chip that is only available in a SOIC or (T)SSOP pinout? This breakout PCB set will make your life much much easier and get you prototyping...

The SparkFun Qwiic Shield for Teensy provides you with a quick and easy way to enter into SparkFun's Qwiic ecosystem with your Teensy boards. This shield is sized...

Convert your thin ZeroCam ribbon cable to a full-sized Raspberry Pi 4/3/2 camera FPC.

The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat’s nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.

Add quadrature encoders to your 20D mm metal gearmotors (extended back shaft version required) with this kit that uses a magnetic disc and Hall effect...

Add connectors to your micro metal gearmotors with these boards that feature side-entry, 2-pin male JST SH-type connectors. These boards are compatible...

This accessory for the Bus Pirate 5 makes it trivial to program bare flash memory chips without clips or soldering. SOP8 150mil and 208mil are the most...

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft....

This side-entry screw terminal block has a pitch of 0.1" (2.54 mm), and can be used as alternatives to standard 0.1" male or female headers on many PCBs...

In a province somewhere in Tamriel, you've been stuck in a dank, dirty dungeon cell for who knows how long. You shake your chains at a rat scurrying across the stone...

This side-entry screw terminal block has a pitch of 0.1" (2.54 mm), and can be used as alternatives to standard 0.1" male or female headers on many PCBs...

If you want to connect multiple EL wires/strips/panels up to one inverter, these splitters are quite useful. There is one male connector (goes to the inverter) and...

These side-entry screw terminal blocks have a pitch of 0.1" (2.54 mm), and can be used as alternatives to standard 0.1" male or female headers on many...

Enhance your Raspberry Pi projects with this dual-access GPIO extension board, featuring both vertical and horizontal pin headers for flexible GPIO access on all 40-pin Raspberry Pi models including Pi 5, 4, and Zero.

You'll have no need for a screwdriver with this terminal! This is a 4-pin Latch Terminal with 5mm pitch pins. Each pin is rated up to 250V @ 11A and will line up...

A set of female header pins for PYBv1.0, PYBv1.1, PYBLITEv1.0 and PYBLITEv1.0-AC.

This side-entry screw terminal block has a pitch of 0.1" (2.54 mm), and can be used as alternatives to standard 0.1" male or female headers on many PCBs...

If you love power adapters or toys & gadgets that have magnetic connections, you can now experiment with these futuristic connectors easily. It's...