Wire Light LED Strand - 12 Cool White LEDs + Coin Cell Holder

SKU: ADA894 Brand: Adafruit

Retired Product

Search for an alternative
This product has been retired. It is no longer available, but this page has been kept for reference.

Add sparkle to your project with these lovely silver wire LED strands. These strands are very interesting, they use two silver wires that are coated so they don't short if they touch, then tiny 1000mcd LEDs are bonded onto the wires and coated with epoxy. The result is a very flexible silver wire with sparkly "fairy" lights that are much less visible than normal LEDs. They're still just LEDs, but in a fun new form-factor! They're even waterproof - you can dunk these or have them outdoors, just be sure to protect the battery holder.

Each strand comes with 12 LEDs, approximately 5cm/2 inches apart for a 2 foot long strand of wire. At one end of the magnet wire, a double stranded-core wire is soldered on and heat-shrinked to protect it. A 2 x CR2032 coin cell holder with on/off switch is on the other side. Of course, if you want you can just cut the coin cell holder off and solder on a 3xAAA battery holder or 3xAA battery holder. To solder to the magnet wire, scrape off the coating first.

Requires 2 x CR2032 batteries to run. Does not come with batteries, We do stock CR2032 batteries if you want to use them as is. Runs for about 8 hours continuously on two CR2032's.

Please note: There are no series resistor installed in the strand, if you want to use another supply you will need to calculate and solder in a resistor. The reason that two 3V coin cells can be used to drive LEDs with a forward voltage of about 3.2V is that coin cells have an internal resistance that makes up for the lack of a choke resistor. If you want to drive these via a 6V power supply, you'll want to put in a 20-220 ohm (or larger) resistor in series to avoid burning out the LEDs. If you want to use a 4.5V power supply, use 10-100 ohms (or larger).

Technical Details

  • LED strand is 26 inches (660mm) long, LEDs are spaced 5cm/2" apart
  • 1000mcd brightness per LED, Forward voltage of 3.2-3.4V @ 20mA
  • Connecting wire is 8 inches (203mm) long
  • Battery holder is 2" x 0.9" x 0.22" (51mm x 23mm x 5.6mm)
  • Weight without batteries: 6.44g
  • Weight with batteries: 12.44g

This product is listed in:

Retired

Product Comments

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

  • $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
  • $6+ for Standard Post (typically 6+ business days, tracked)
  • $10+ for Express Post (typically 2+ business days, tracked)
  • Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

  • $11+ for Pack and Track (3+ days, tracked)
  • $16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review

Guides

The Maker Revolution

The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...

Projects

Raspberry Pi Video Looper Display Installation | Overshare Video Festival

IntroductionA suspended ceiling display of forty repurposed screens and displays, each screening cr...
IntroductionA suspended ceiling display of forty repurposed screens and displays, each screening cr...

Mailbox Delivery Notification System

Introduction During the Covid lockdown, I needed something to do. The Postman or woman does not de...
Introduction During the Covid lockdown, I needed something to do. The Postman or woman does not de...

PiicoDev Schematic System

Introduction: Hi everybody. Over the past few weeks, I have been working on an intuitive system th...
Introduction: Hi everybody. Over the past few weeks, I have been working on an intuitive system th...
Feedback

Please continue if you would like to leave feedback for any of these topics:

  • Website features/issues
  • Content errors/improvements
  • Missing products/categories
  • Product assignments to categories
  • Search results relevance

For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.

Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.

Makers love reviews as much as you do, please follow this link to review the products you have purchased.