SparkFun Artemis Development Kit

SKU: DEV-16828 Brand: Sparkfun

The SparkFun Artemis Development Kit is the latest board to be released around the SparkFun Artemis Module and it allows access to more software development features...

$82.10 AUD, inc GST

$74.64 AUD, exc GST

Available with a lead time
Expect dispatch between May 26 and May 27

Quantity Discounts:

6+ $71.65 (exc GST)
12+ $69.41 (exc GST)

The SparkFun Artemis Development Kit is the latest board to be released around the SparkFun Artemis Module and it allows access to more software development features than previous Artemis based boards. Recommended software used to program the Artemis DK are the Arduino IDE, Arm® Mbed™ OS CLI, and AmbiqSDK. An updated USB interface (MKL26Z128VFM4 Arm® Cortex-M0 MCU, from NXP) allows the Artemis Dev Kit to act as:

Mass Storage Device (MSD): Used to provide drag and drop programming to the Artemis Module.
Human Interface Device (HID): Used for the debugging interface to the Artemis Module.
Communication Port (COM): Used to provide a serial communication UART between the Artemis and the USB connection (PC).

The Artemis Module provides a Cortex-M4F with BLE 5.0 running at 48MHz with an available 96MHz turbo mode and power as low as 6uA per MHz (less than 5mW). The SparkFun Artemis Module is fully FCC/IC/CE certified with 1M flash and 384k RAM you'll have plenty of room for your code. The flexibility of the Artemis module starts with our Arduino core. You can program and use the Artemis module just like you would an Uno or any other Arduino. Additional functionality stems from the ability of the Artemis Dev kit to run RTOS such as the Arm Mbed OS, or the AmbiqSDK.

Attached to the "Qwiic" I²C bus, we've added a LIS2DH12TR MEMS accelerometer (for things like gesture recogntion), a digital MEMS microphone, and an edge camera connector for the Himax CMOS imaging camera (not included) to experiment with always-on voice commands, and image recognition with TensorFlow and machine learning. All of the Artemis Development Kit pins are broken out to 0.1" spaced female headers (i.e. connectors). There are also two rows of breakout pins with .1" pitch spacing for headers; and a .08" pitch spacing to clip on IC-hooks, used by most logic analyzers. Additionally the Silk on the back of the Artemis DK acts as a chart to show pins by functionality (peripherals, ADC, PWM, UART0, & UART1) and act as an aid while developing software. The board is powered & programmed via USB-C, and includes a Qwiic connector to make I²C easy and is fully compatible with SparkFun's Arduino core to be programmed under the Arduino IDE. The Artemis DK Kit with Camera is the easiest way to get started with all the accessories you need.

Features

Compatible with Arduino, Mbed-CLI, and AmbiqSDK Development Programs
Power:
- 5V Provided Through the USB-C Connector
- 1.8V, 3.3V, and 5V Available on Power Header
Interface Chip (MKL26Z128VFM4 ARM^® Cortex^®-M0 MCU):
- Drag and Drop Programming
- SWD Interface
- JTAG Programming PTH
Artemis Module:
- Apollo3 ARM^® Cortex^®-M4F MCU
- BLE 5.0 with FCC Certification
- 24 Breakout I/O Pins
  - Eight 14-bit ADC Pins
  - Eighteen 16-bit PWM Pins
  - Two Independent UART Ports
  - Three Peripheral I²C/SPI Buses
- JTAG Programming PTH
Sensors:
- 3-axis Accelerometer (LIS2DH12)
- PDM Microphone (SPH0641LM4H-1)
- Camera Connector (for the Himax HM01B0 Camera)
Qwiic Connector
- On Primary I²C Bus

Documents

Schematic
Eagle Files
Board Dimensions
Hardware Component Information:
- Artemis Module:
- Interface Chip:
  - MKL26Z128VFM4 Datasheet
  - MKL26P64M48SF5 Reference Manual
- PDM Microphone (SPH0641LM4H-1) Datasheet
- Accelerometer (LIS2DH12) Datasheet
- SparkFun Qwiic Connect System
GitHub Hardware Repository
GitHub Repository for Apollo3 Board Support Packages (BSP)
- DAPLink Bootloader: kl26z_artemis_dk_if.bin
- DAPLink Interface Firmware: kl26z_bl.bin
Development Platforms for Artemis Module:
- SparkFun Ambiq Apollo3 Arduino Core
  - .json file needed for the SparkFun Ambiq Apollo3 Arduino Core: https://raw.githubusercontent.com/sparkfun/Arduino_Apollo3/master/package_sparkfun_apollo3_index.json
- Mbed™ OS
- AmbiqSDK
- pyOCD

Product Comments

Start the conversation

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

$3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
$7+ for Standard Post (typically 6+ business days, tracked)
$11+ for Express Post (typically 2+ business days, tracked)
Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

$12+ for Pack and Track (3+ days, tracked)
$16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!