PA Amplifier Stereo 2x500W

SKU: AA4172

Retired Product

Search for an alternative
This product has been retired. It is no longer available, but this page has been kept for reference.
Bridgeable “PA Series”. This monster Biema produces a massive 1500W into 8 ohms in Bridge mode, 750W per channel into 4 ohms or 500W per channel into 8 ohms. The massive power capacity together with enhanced engineering and design facilitates ultra service reliability, ensuring it is the perfect choice for both hire applications and for permanent installations. It performs tirelessly even in the most demanding applications and is ideal for nightclubs, sporting complexes, cinemas, mobile DJ’s, pub and club PA’s and bands. Engineered with two extra large heatsink tunnels cooled with thermally cued fans which reduce their speed at standby or low level inputs. To ensure superior reliability, the amplifier includes a host of protection circuitry permitting operation under the most demanding applications. Features include over-temperature shut down, short circuit protection and output limiting. Each channel includes its own recessed front mounted volume control, rear panel mounted XLR and 6.35mm jack balanced inputs with selectable sensitivity of 0.77V, 1.4V and 3.5V. Enabling input signals from a wide variety of source equipment. Speaker connections are made via heavy duty binding posts or industry standard heavy duty speaker connectors.

Features

  • Rugged heavy duty construction
  • 19” rack mount
  • Stylish cosmetics
  • 3 modes of operation - stereo, parallel and bridged
  • Selectable input sensitivity
  • Soft start limiter
  • Earth lift switch
  • Limiter on/off switch
  • XLR & 6.35mm balanced inputs
  • Binding post & industry standard heavy duty output speaker connectors
  • Front & rear carry handles
  • Clipping & overload/overdrive protect indicators
  • Recessed detent volume controls for each channel
  • Thermally cued fan forced cooling


Specifications

  • Output power (RMS): 2 x 500W (8Ω)
  • tested at 1kHz at <0.1% THD: 2 x 750W (4Ω), 1 x 1500W (Bridged 8Ω)
  • Freq. Response: 10Hz - 50kHz (-1.5dB)
  • Input sensitivity: 0.77V
  • Signal to noise ratio: >90dB
  • Dimensions (mm): ≈ 482W x 506D x 88H
  • Weight: 22kg
  • Note: Close up internal shot shown is for A 4180, however internals for both of these amplifiers look the same.

Downloads

This product is listed in:

Retired

Product Comments

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

  • $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
  • $7+ for Standard Post (typically 6+ business days, tracked)
  • $11+ for Express Post (typically 2+ business days, tracked)
  • Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

  • $12+ for Pack and Track (3+ days, tracked)
  • $16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review

Guides

The Maker Revolution

The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...

Projects

Spectral Animations with a DIY MSGEQ7 I2C Device

Frequency Reactive LEDs, i2c Protocol, Raspberry Pi, and Other Adventures.Here at Pix Incorpor...
Frequency Reactive LEDs, i2c Protocol, Raspberry Pi, and Other Adventures.Here at Pix Incorpor...

VisionSphere: Camera Motion Detection for Raspberry Pi

A simple camera motion detection system for Raspberry Pi. Definitely written with Aussie's in mind ...
A simple camera motion detection system for Raspberry Pi. Definitely written with Aussie's in mind ...

Arduino E-Paper Clock

This project started with a desire to have a modern digital clock that would use the natural light ...
This project started with a desire to have a modern digital clock that would use the natural light ...
Feedback

Please continue if you would like to leave feedback for any of these topics:

  • Website features/issues
  • Content errors/improvements
  • Missing products/categories
  • Product assignments to categories
  • Search results relevance

For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.

Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.

Makers love reviews as much as you do, please follow this link to review the products you have purchased.