Search results for: 'standoff set'

These screw can be used to isloate your circuit board. It is suitable for all kinds of circuit boards, sensors, mechanical mounting.

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot chassis. This 10-pack of standoffs includes 10 sets screws and nuts for securing the top of the standoff to your project.

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation.

Totaling 380 pieces, this M2.5 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for...

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation.

This 210 piece brass standoff kit insures you'll always have a set handy...

Totaling 420 pieces, this M3 Screw Set is a must-have for your workstation. You'll have enough screws, nuts, and hex standoffs to fuel your maker tendencies for days on end!

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation.

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot chassis.

These screw can be used to isloate your circuit board. It is suitable for all kinds of circuit boards, sensors, mechanical mounting.

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation.

The 80mm length, M4-threaded, 8mm REX Standoff provides clearance, adjusts distances between parallel parts, and reinforces structures. You.....

14mm length standoffs can be used to add structural rigidity between parallel plates, as a stub-axle to run bearings and rotating...

Protect your Alchitry board by adding these stylish standoffs! The bolts protrude about 2mm below the board which is just further than the lowest part on...

A 30mm long aluminium standoff for M4 threaded screws

A 43mm long aluminium standoff for M4 threaded screws

A 60mm long aluminium standoff for M4 threaded screws

A plastic spacer with an inner diameter for 6mm

A 42mm long aluminium standoff for M4 threaded screws

A 40mm long aluminium standoff for M4 threaded screws

These 1/2"-long hexagonal female-female aluminum standoffs keep parts spaced 0.5 inches (13 mm) apart. They are like elongated, 3/16″-wide hex nuts, with 4-40 threads running through the entire length of each standoff. They are sold in packs of 4.

A 56mm long aluminium standoff for M4 threaded screws

A plastic spacer with an inner diameter for 4mm

A 22mm long aluminium standoff for M4 threaded screws

The 120mm length, M4-threaded, 8mm REX Standoff provides clearance, adjusts distances between parallel parts, and reinforces structures....

These nylon standoffs are ¾" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or just getting it up off the table.

These hexagonal male-female aluminum standoffs keep parts spaced 0.25" (6 mm) apart and are great for building a multi-level robot chassis. Both ends of these 3/16"-wide standoffs have 2-56 threads. The standoffs are sold in packs of 4.

A 24mm long aluminium standoff for M4 threaded screws

Stock your warchest with essential standoffs with the 8mm REX™ Standoff Bundle! Fancier parts might make the headlines, but the simple.....

A 38mm long aluminium standoff for M4 threaded screws

12mm length standoffs can be used to add structural rigidity between parallel plates, as a stub-axle to run bearings and rotating...

For those times where it would be helpful to have holes offset 4mm from the original locations. Offset standoffs have three mounting...

The 24mm height from base to center will cause parts to remain on pattern between the goRAIL and the surface that the standoffs are...

These hexagonal male-female aluminum standoffs keep parts spaced 1.25" (32 mm) apart and are great for building a multi-level robot chassis. Both ends of these 3/16"-wide standoffs have 2-56 threads. The standoffs are sold in packs of 4.

These 1/4"-long hexagonal female-female aluminum standoffs keep parts spaced 0.25 inches (6.4 mm) apart. They are like elongated, 3/16″-wide hex nuts, with 4-40 threads running through the entire length of each standoff. They are sold in packs of 4.

These hexagonal male-female aluminum standoffs keep parts spaced 1.5" (38 mm) apart and are great for building a multi-level robot chassis. Both ends of...

The 24mm height from base to center will cause parts to remain on pattern between the goRAIL and the surface that the standoffs are...

These hexagonal male-female aluminum standoffs keep parts spaced 1.0" (25 mm) apart and are great for building a multi-level robot chassis. Both ends of these 3/16"-wide standoffs have 4-40 threads. The standoffs are sold in packs of 4.

These hexagonal male-female aluminum standoffs keep parts spaced 1.25" (32 mm) apart and are great for building a multi-level robot chassis. Both ends of these 3/16"-wide standoffs have 4-40 threads. The standoffs are sold in packs of 4.