Search results for: 'schottky diode'

1A Forward Current, 1.1V Forward Voltage Drop.

0.2A Forward Current, 1V Forward Voltage, Fast Switching Type.

This is a common MOSFET with very low on-resistance and a control voltage (aka gate voltage) that is compatible with any 3-5V microcontroller...

When you need to switch a lot of power, N channel MOSFETs are best for the job.

This is a boost converter. Supply voltage as low as 5v, it boosts to as high as 32v.

General Purpose Transistor - BC547

This here is a 10 pack of the classic 1N4001 power blocking diode. These are good for reverse polarity protection (put it between your DC power jack and circuitry...

Use this simple IR receiver for infrared remote control of your next project. With low power consumption and an easy to use package, it mates well with embedded electronics and can be used with common IR remotes.

1A Forward Current, 1.1V Forward Voltage Drop.

This module consists of two ideal diode circuits with their outputs connected to form a power ORing arrangement, which can be used for load sharing or for...

This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to control a high voltage side.

If you do anything with electronics, you’re probably already using transistors, but you’re probably using them in large, prepackaged clusters of just one type. The SparkFun Discrete Semiconductor Kit addresses your needs of only needing one or a couple transistors without you needing go and order a single transistor. Inside each kit you will find multiple types of semiconductors including PNP and NPN bipolar transistors, N-channel and P-channel MOSFETs, diodes, adjustable voltage references, and adjustable voltage regulators.

This simple device operates at 940nm and works well for generic IR systems...

The BPW34 is a tiny, general purpose PiN photodiode. This photodiode has a ton of uses, one of which is to use it is a mini solar cell to power your project. The cell is sensitive to a wide range of light wavelengths (430-1100nm), so it should produce power in a number of different settings. The rated open circuit voltage is 350mV (900nm, 1mW/cm2 light source), and short circuit current is 47μA.

Better grab your sunglasses, your sunscreen, and a bucket hat because this 3W RGB LED is so bright it's like like taking a beach vacation ON THE SUN. Maybe that's...

DO-41 Package.

This is a simple, subminiature size, axial lead mounted rectifier diode. Often used for reverse voltage protection, the 1N4004 is a staple for many power, DC to...

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.

This breadboard-compatible module is an alternative to bulky power switches. It uses a small integrated slide switch to control a high-side power MOSFET that can deliver continuous currents up to around 16 A at 4.5 V to 40 V. The board features reverse-voltage protection and also makes it easy to control the MOSFET with an external switch or the digital output of a microcontroller.

This is a very common signal diode - 1N4148. Use this for signals up to 200mA of current.

This breadboard-compatible module is an alternative to bulky power switches. It uses a small integrated slide switch to control a high-side power MOSFET...

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow.

The SparkFun MY1690X Serial MP3 Player Shield is an awesome decoder that can store music files onto a standard microSD card, allowing you to add music or...

Is your QT Py all alone, lacking a friend to travel the wide world with? When you were a kid you may have learned about the "buddy" system, well...