Search results for: 'jst to male header cable'

This cable will let you turn a JST PH 3-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. Adafruit are carrying these to match...

If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin...

If you're fancying to connect to the debug port on a Pico WH, or the two ports on a Pico Debug Probe or anything else with a JST SH compatible 3-pin...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. Adafruit are carrying these to match...

This cable is ideal for connecting your encoder to a Roboclaw motor controller as well as male pins on Arduinos and Raspberry Pi's.

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared...

For a really long time Adafruit assumed that the JST PH didn't have a free-hanging male header version. But then Adafruit found this JST-PH 2-pin Male Cable, and Adafruit were like...

These simple boards serve as adapters between a JST SH-style 2-pin male connector and breadboard-compatible 0.1"-pitch through holes.

This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and female connectors on the other. The cable insulation is...

This simple board serves as an adapter between a JST PH-style 5-pin, side-entry connector and breadboard-compatible 0.1"-pitch through holes. The PH...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

This simple board serves as an adapter between a JST SH-style 6-pin male connector and breadboard-compatible 0.1"-pitch through holes. It works with our ...

These simple boards serve as adapters between a JST SH-style 2-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

These simple boards serve as adapters between a JST SH-style 5-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

These simple boards serve as adapters between a JST SH-style 4-pin male connector and breadboard-compatible 0.1"-pitch through holes.

These simple boards serve as adapters between a JST SH-style 3-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

These simple boards serve as adapters between a JST SH-style 4-pin male connector and breadboard-compatible 0.1"-pitch through holes. They work with our...

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based device’s pins.

This 3 Pin JST-SH Cable is a 30cm cable for solderless Serial Wire Debug (SWD) connections for Raspberry Pi Pico, Pico H, and Pico WH boards. It features...

A handy little cable that connects to the JST connector on the underside of HyperPixel 4.0, allowing you to use I2C devices with your Raspberry Pi at the same time as the display.

You might have seen these cables used in computers. They are typically used to bring USB connections from a motherboard to the external case, or the rear expansion slots. They have a 0.1" spaced 4-pin header on one end and a USB A connector on the other.