Search results for: 'i2c header'

Perfect for prototyping, the straight male header is a super common header type so grab a few and put your ideas to the test!

Perfect for prototyping, these straight male headers are a super common header type so grab a few and put your ideas to the test!

Perfect for prototyping, the stacking header lets your signal and power flow through your project, grab a few and put your ideas to the test!

This Gravity: I2C HUB module is designed to connect up to 8 I2C devices to a main-controller, which allows you easily to hook up multiple I2C devices in project...

This is a super small, 2x5 pin male PTH header. This header is in the common configuration for JTAG applications. Each pin has a spacing of 1.27mm in between each...

Connect your own PCB to a Raspberry Pi with this normal-height female header. The female header part is about 8.5mm tall, good for small HATs that do not to clear...

This module enables galvanically isolated bidirectional I²C communication between two devices while supplying regulated, isolated power to the target. The...

This USB-to-I²C adapter enables a PC or other USB host to act as the controller on an I²C bus, reading and writing data from I²C target devices connected...

These stackable headers are made to work with the SparkFun Qwiic Shield for Arduino Nano or any comparable shield to connect the shield with a Arduino Nano footprint...

This module enables galvanically isolated bidirectional I²C communication between two devices while supplying regulated, isolated power to the target. The...

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the through-hole version of the SMT GPIO Header for...

I2C Breakout shield for the TinyPICO & TinyS2...

Expand the power of your Nano projects with easy cable connectivity. The Arduino Nano Connector Carrier brings plug-and-play simplicity to the Nano family, making it faster than ever to prototype with Qwiic, Grove, and Modulino modules, and to unlock new potential with onboard microSD storage.

Simple shrouded 10-pin connector. Good for preventing cable connection mishaps. Use for programming, data, power, or any other kind of connection. 2x5 pins on 0.1" centers.

The Adafruit TCA4307 Hot-Swap I2C Buffer breakout here solves that problem. It's specifically designed to take a non-hot-swap protocol (I2C) and protect the controller from wayward peripherals messing with the bus during attach/detach.

The fully-featured robot motor expansion board supports multiple motors and servos. Perfect for Raspberry Pi Zero/Zero W/A+/B+/2B/3B/3B+/4B. ...

This is a SMD 4-pin right angle male header. We use this header on our Graphic LCD Serial Backpack.

A Raspberry Pi mini HAT designed to help you take the best possible care of your plants. It can tell you how well they're hydrated, attract your attention...

This USB-to-I²C adapter enables a PC or other USB host to act as the controller on an I²C bus, reading and writing data from I²C target devices connected...

This is a simple 2x3 male PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between each other.

The I2C Switch from AB Electronics UK is a 4 channel bidirectional I2C switch controlled via the I2C-bus. It is designed for use on all Raspberry Pi models with the 40 pin GPIO connector.

I²CMini is an easy-to-use, open-source tool for controlling I²C devices over USB, 100% compatible with I²CDriver. Its a small friend that will make working with I2C a breeze, especially if they have a Qwiic/Stemma QT or even Grove I2C connector!

This module enables galvanically isolated bidirectional I²C communication between two devices. The bidirectionality applies to both SDA and SCL, which...

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won’t work. The surface mount side of the legs are staggered for stress relief.

The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access...

If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Dev Breakout is a great landing spot. The SparkFun SAMD21 Dev Breakout is an Arduino-sized breakout for the Atmel ATSAMD21G18, a 32-bit ARM Cortex-M0+ processor with 256KB flash, 32KB SRAM, and an operating speed of up to 48MHz. This dev breakout provides you with an Arduino hardware option that solves the problems of low storage limits and dynamic memory stack overflows that have plagued the previous iterations of the Arduino family. Yes, the SparkFun SAMD21 Dev Breakout is even fully supported in the Arduino IDE and libraries for the Arduino Zero!

These are standard 0.1" spaced header pins that can be surface mounted for applications where through-hole pins won’t work. The surface mount side of the legs are staggered for stress relief.

Simple shrouded 6-pin connector. Good for preventing cable connection mishaps. Use for programming, data, power, or any other kind of connection. 2x3 pins on 0.1" centers.

This is a simple 3 pin female PTH header. This header is in a configuration that makes it ideal to be used with the MyoWare Muscle Sensor line. Each pin has a spacing of 0.1" in between each other.

This is a simple 2x8 male PTH header. This header is that you will find commonly used to interface with a basic 8x2 character LCDs. Each pin has a spacing of 0.1" in between each other.