Search results for: 'cable gland housing'

This 200mm cable breaks out the four wires in a PiicoDev cable for manual wiring to breadboards or development boards. It's a 4-wire harness with an SH connector on one end and four Dupont-style connectors on the other.

Keep your projects safe and dry with this IP67 PC enclosure

This is a package of crimp pins for female housing pins with the pitch of 2.54mm.

Are you frustrated by the lack of customization options for your jumper wires? Look no further! Compatible with both male and female wires, these fully customizable...

These are our small, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it!

This 6-conductor, 75 cm (30") cable has 24 AWG wires and a 6-pin female JST PH-type connector (2mm pitch) on one end. The other ends of the wires are...

This 2-conductor, 12 cm (4.5") cable has 24 AWG wires and a 2-pin female JST PH-type connector (2mm pitch) on one end. The other ends of the wires are...

No, this isn’t a tank tread, this is a 0.5m long Cable Carrier with 10x15mm bits composing its main body and two screw fasteners at each end for efficient mounting. Sometimes called a “drag chain,” each carrier can be used in projects with a large number of moving parts to protect internally installed cables, pipes, or tubes so they can be bent and moved while remaining protected. Cable carriers can most commonly been found in 3D printers and CNC machines but they can be used in any situation where you need cables or tubes to bend without risk of them being damaged or wearing out prematurely.

These beefy, bright red plastic enclosures will give your widget the protection (and attention) it deserves. You’ve probably seen these used to enclose radio equipment or antenna baluns as they can be secured to a pole using U-bolts (not included). At about 3mm thick, this 74x158x90mm enclosure has plenty of space for gizmos, gadgets, widgets and doohickeys. The mounting flanges extend 19mm from either edge with two 50mm-spaced 7mm diameter holes.

Enhance your DeskPi RackMate setup with this 0.5U 10" cable entry panel featuring a dust-preventing brush strip, perfect for maintaining clean cable management and optimized airflow in your mini server rack.

These are our large, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it!

This is a 4-pin female housing pin with a pitch of 2.54mm.

These hard-to-find 6-pin (2×3) shrouded male headers are great general-purpose connectors and are perfect for AVR ISP programming and work with Pololu's 6-pin IDC sockets and 6-conductor ribbon cables with IDC connectors.

This 5-conductor, 30 cm (12") cable has 24 AWG wires and a 5-pin female JST PH-type connector (2mm pitch) on one end. The other ends of the wires are...

This 4-conductor, 12 cm (4.5") cable has 24 AWG wires and a 4-pin female JST PH-type connector (2mm pitch) on one end. The other ends of the wires are...

This 3-conductor, 75 cm (30") cable has 24 AWG wires and a 3-pin female JST PH-type connector (2mm pitch) on one end. The other ends of the wires are...

These semi-transparent plastic enclosures are handy for keeping electronics that need to live outside dry - great for nature cameras and greenhouse...