Search results for: '4 pin cable'

This 4-wire cable is 50mm / 1.9" long and fitted with JST SH female 4-pin connectors on both ends. Compared with the chunkier JST PH these are 1mm pitch instead...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium female headers on the other. Compared with...

4 pin Female Jumper to Grove 4 pin Conversion Cable is being made available based on requests from customers to use Grove modules directly with Arduino...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the other. Compared...

Grove is a convenient plug-and-play system with the specialized interface, but that doesn't mean it couldn't be used in an open ecosystem like a breadboard

The Gravity 4Pin IIC/I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 30cm length. One side is PH2.0-4p connector and the other side is XH2.54...

The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards...

This 4-conductor, 12 cm (4.5") cable has 24 AWG wires and a 4-pin female JST PH-type connector (2mm pitch) on one end. The other ends of the wires are...

This 4Pin solderless strip connector comes with wire and adopts snap-down design at both ends, which makes a firm and easy connection of 10mm wide 4-wire...

This 4-conductor, 63 cm (25") cable has 28 AWG wires and 4-pin female JST SH-type connectors on both ends...

Are you a maker in the midst of a STEMMA dilemma? This 200mm long 4-wire cable is a fantastic chimera-cable fitted with STEMMA QT / Sparkfun Qwiic JST SH on one...

These solid 2.0mm pitch connector cable pairs are great when you need something that can carry a couple of amps of current and are easy to connect and disconnect.

These solid 2.5mm pitch connector cable pairs are great when you need something that can carry a couple amps of current, easy to connect and disconnect, and is just-about 0.1" pitch compatible.

This 4-wire cable is a little over 100mm / 4" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm pitch...

This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" male header plugs on the end. Adafruit are carrying these to match...

This 4-wire cable is a little over 200mm / 7.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH these are 1mm...

This cable will let you turn a JST PH 4-pin cable port into 3 individual wires with high-quality 0.1" female sockets on the end. Adafruit are carrying these to match up...

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection.

When 0.1" is too big, and JST PH's too chunky, these ultra-slim 1.25mm connectors are a reliable alternative. These are only 1.25mm pitch, but have a nice clicky connection.

This 4-wire cable is a little over 400mm / 15.7" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH...

The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards...

This 4-wire cable is a little over 300mm / 11.8" long and fitted with JST-SH female 4-pin connectors on both ends. Compared with the chunkier JST-PH...

For big projects with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. The only problem is that these supplies have...

If you're messing around with floppy drives, or disk drives, or other devices that are usually powered with a PC motherboard you'll often see...

Compared with the Electronic Brick system, the Grove System uses only 1 type of cable, (the Electronic Brick system uses 4). These cables are compatible...

These 4-wire cables are 15cm long and come as a set, one side has a JST SM type connector plug on the end. The other side has a matching JST SM type receptacle connector...

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers.

This 4-conductor, 75 cm (30") cable has 28 AWG wires and a 4-pin female JST SH-type connector on one end. The other ends of the wires are unterminated;...

This cable will make it super easy to use Adafruit's plug-and-play STEMMA QT boards with boards like Circuit Playground. On one end you get a Qwiic / STEMMA QT connector...

The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards...

The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards...

For big projects, with big power needs, an AT or ATX power supply is a handy place to grab 5V or 12VDC. Only problem is that these supplies have connectors that...

This 4-PIN solderless LED strip connector comes with 20cm wire connected to a DuPont-style female connector, and the other end employs snap-down design...

This 4-conductor, 63 cm (25") cable has 24 AWG wires and 4-pin female JST PH-type connectors (2mm pitch) on both ends...

This cable will let you turn a JST PH 4-pin cable port into 4 individual wires with grippy mini alligator clips. Adafruit are carrying these to match up with any of our...

The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards...