Three bench instruments in one battery-powered unit: an oscilloscope (100 MHz on a single channel), a True RMS multimeter and a signal generator.
Available with a lead time
Expect dispatch between Nov 27 and Dec 14
A two-channel digital oscilloscope with a True RMS multimeter and a 10 MHz signal generator built in, for finding faults in circuits at the bench or on a job site.
It replaces three separate instruments with one unit that stands on the bench and runs from an internal 5000 mAh battery, charged over USB-C. That makes it practical where mains power is awkward to reach, and in a teaching lab, one unit per station covers common test equipment: the scope, meter and generator.
The oscilloscope samples at 500 MSa/s with up to 1M points of memory. Bandwidth is 100 MHz with one channel active and 50 MHz with both channels on, so plan around 50 MHz when you compare two fast signals. You control it from a 4.3-inch (109 mm) IPS touchscreen, with physical buttons and rotary encoders for vertical, horizontal and main adjustment.
It comes ready to measure, with two P6100 x1/x10 probes, multimeter test leads and a BNC alligator clip lead. The 800 V maximum input applies only through a probe set to x10. FNIRSI does not state a limit for direct x1 input, and it publishes no CAT safety rating.
Follow fast edges and switching noise up to 100 MHz on one channel, with 500 MSa/s real-time sampling
Choose between longer records and finer detail with 10K, 100K or 1M points of memory depth
Measure power-supply ripple with less noise using the selectable 20 MHz bandwidth limit
Spot intermittent glitches and see how often a signal varies: persistence from minimum to infinite, shown as 128 levels of grey or colour temperature, at about 1200 waveforms captured per second
Read common signal values without counting divisions, using 13 automatic measurements and cursors
Combine channels with add, subtract, multiply and divide, and plot one channel against the other in XY mode
Catch one-off events with Auto, Normal and Single trigger modes on rising, falling or both edges
Drive a circuit under test from the 10 MHz DDS generator: up to 11 common waveforms, 0.1 to 3.0 Vpp, duty cycle 0 to 100%
Check voltage, current, resistance, capacitance, diodes and continuity on the 19,999-count True RMS multimeter, up to 1000 V DC, 750 V AC and 9.999 A
Watch a reading drift over time with Curve View, a live trend graph of measurements
Work away from mains power on the internal 5000 mAh lithium battery, recharged over USB-C
Property | FNIRSI 2D15P |
|---|---|
Oscilloscope channels | 2 |
Sample rate | 500 MSa/s |
Analogue bandwidth | 100 MHz (one channel); 50 MHz (both channels) |
Bandwidth limit | 20 MHz, selectable |
Memory depth | 10K, 100K, 1M points |
Input impedance | 1 MΩ |
Timebase range | 5 ns to 50 s |
Vertical sensitivity | 10 mV to 10 V/div |
Maximum input voltage | 800 V (probe set to x10) |
Coupling | AC, DC |
Trigger modes | Auto, Normal, Single |
Trigger types | Rising, falling, both edges |
Display modes | Dot, vector, colour temperature |
Persistence | Minimum, 2 s, 5 s, 10 s, 20 s, 50 s, infinite |
Waveform capture rate | Approx. 1200 waveforms/s |
Automatic measurements | 13 |
Analysis | Math (add, subtract, multiply, divide), XY mode, cursors, Curve view trend graph, waveform save and export |
Multimeter | 19,999 counts, True RMS |
DC voltage ranges | 1.9999 V / 19.999 V / 199.99 V / 1000 V |
AC voltage ranges | 1.9999 V / 19.999 V / 199.99 V / 750.0 V |
DC current ranges | 19.999 mA / 199.99 mA / 1.9999 A / 9.999 A |
AC current ranges | 19.999 mA / 199.99 mA / 1.9999 A / 9.999 A |
Resistance ranges | 199.99 Ω / 1.9999 kΩ / 19.999 kΩ / 199.99 kΩ / 1.9999 MΩ / 19.999 MΩ |
Capacitance ranges | 9.999 nF / 99.99 nF / 999.9 nF / 9.999 µF / 99.99 µF / 999.9 µF / 9.999 mF / 99.99 mF |
Other multimeter functions | Diode, continuity |
Signal generator | 1 channel, DDS |
Generator frequency | 0 to 10 MHz |
Generator amplitude | 0.1 to 3.0 Vpp |
Generator duty cycle | 0 to 100% |
Generator waveforms | Up to 11 common waveforms |
Display | 4.3-inch (109 mm) IPS capacitive touchscreen |
Controls | Physical buttons; rotary encoders for vertical, horizontal and main adjustment |
Connectors | 3x BNC (CH1, CH2, GEN); USB-C |
Architecture | FPGA + MCU + ADC |
Battery | 5000 mAh lithium, USB-C charging |
Firmware | Upgradeable (Windows 10/11 PC required) |
Operating environment | -5 to 40 °C, up to 80% RH |
Shipping weight | 1.10 kg |
FNIRSI manuals and firmware (the 2D15P is listed under Benchtop Oscilloscope Multimeter)
Firmware updates must be installed from a Windows 10 or 11 PC. FNIRSI warns that updating from macOS is not supported and can leave the unit unusable.
1x 2D15P oscilloscope, multimeter and signal generator
2x P6100 oscilloscope probes
1x multimeter test lead set
1x BNC alligator clip lead
1x USB data cable
1x user guide
This product is listed in:
Test Equipment>Digital OscilloscopesExact shipping can be calculated on the view cart page (no login required).
Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).
We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):
Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.
Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.
International Orders - the following rates are for New Zealand and will vary for other countries:
If you order lots of gear, the postage amount will increase based on the weight of your order.
Our physical address (here's a PDF which includes other key business details):
40 Aruma Place
Cardiff
NSW, 2285
Australia
Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.
Have a product question? We're here to help!
Makers love reviews as much as you do, please follow this link to review the products you have purchased.
Product Comments