Dust Sensor Module Kit - GP2Y1014AU0F with Cable

SKU: ADA4649 Brand: Adafruit
This simple dust sensor is a great way to add basic particulate sensing to your next project. It's not as fully featured as Adafruit's PM2.5 I2C/UART-based sensors, with just a single analog voltage output.
$16.70 AUD, inc GST
$15.18 AUD, exc GST

In stock, ships same business day if ordered before 2PM
Delivered by Tue, 5th of Aug

Quantity Discounts:

  • 10+ $14.57 (exc GST)
  • 25+ $14.12 (exc GST)
- +

5 from local stock, 1 supplier stock; your order will dispatch between Dec 1 to Dec 10. And yes, stock levels and lead times are accurate!

Shipping:

  • $7+ Standard (5+ days*, tracked)
  • $11+ Express (2+ days*, tracked)
  • FREE Pickup (Newcastle only - must order online*)

Shipping costs may increase for heavy products or large orders.

Exact shipping can be calculated on the view cart page.

*Conditions apply, see shipping tab below.

This simple dust sensor is a great way to add basic particulate sensing to your next project. It's not as fully featured as Adafruits PM2.5 I2C/UART-based sensors, with just a single analog voltage output. However, for the price, it can't be beat! The SHARP GP2Y1014AU0F Dust Sensor Module Kit particulate sensor uses an LED to bounce off of particles suspended in the air - much like you can clearly see how dusty the air is when a sun beam lights up your room!

This sensor has a few tradeoff's compared to Adafruits other PM2.5 sensors:

  • You need a fast GPIO toggle to trigger the measurements, for that reason it's only for use with Arduino or other non-interpreted languages. E.g. not for use with CircuitPython
  • You only get an analog voltage output that tells you how dusty it is - higher voltage = dustier, ranging from 0 to 0.5 mg/m3. It isn't precise!
  • You need to power it from 5V - however the output voltage can be read by a microcontroller that's running on 3.3V (the analog output maxes out at 3.6V)

Kit includes:

  • 1x GP2Y1014AU0F sensor
  • 1 x 6-pin pig-tail cable for interfacing with the sensor easily
  • 1 x 150 ohm resistor
  • 1 x 220uF capacitor

To use:

  • Connect Blue wire to 5V through a 150 ohm resistor (included)
  • Connect included 220uF capacitor between 5V and ground.
  • Connect Yellow and Green wires to Ground
  • Connect Write wire to a digital output (to control the LED)
  • Connect Black wire to an analog input (say A0)
  • Connect Red wire to 5V

Run Adafruits example sketch on any Arduino and open the serial monitor to read the values out.

Example usage schematic

SHARP GP2Y1014AU0F Datasheet

Product Comments

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

  • $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
  • $7+ for Standard Post (typically 6+ business days, tracked)
  • $11+ for Express Post (typically 2+ business days, tracked)
  • Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

  • $12+ for Pack and Track (3+ days, tracked)
  • $16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

40 Aruma Place
Cardiff
NSW, 2285
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review

Guides

The Maker Revolution

The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...

Configuring 8Bitdo N64 Controller Mapping

RetroPie is a fantastic system, and once you map your input device, it will take those mappings and ...
RetroPie is a fantastic system, and once you map your input device, it will take those mappings and ...

How to Build a RetroPie Console

Perhaps you’ve read our Gaming Kit for RetroPie tutorial on how to setup a RetroPie console an...
Perhaps you’ve read our Gaming Kit for RetroPie tutorial on how to setup a RetroPie console an...

Gaming Kit for RetroPie

Video gaming has evolved tremendously over the last decade, console games produce near real-life gra...
Video gaming has evolved tremendously over the last decade, console games produce near real-life gra...

Projects

Configuring 8Bitdo N64 Controller Mapping

RetroPie is a fantastic system, and once you map your input device, it will take those mappings and ...
RetroPie is a fantastic system, and once you map your input device, it will take those mappings and ...

How to Build a RetroPie Console

Perhaps you’ve read our Gaming Kit for RetroPie tutorial on how to setup a RetroPie console an...
Perhaps you’ve read our Gaming Kit for RetroPie tutorial on how to setup a RetroPie console an...

Gaming Kit for RetroPie

Video gaming has evolved tremendously over the last decade, console games produce near real-life gra...
Video gaming has evolved tremendously over the last decade, console games produce near real-life gra...
Feedback

Please continue if you would like to leave feedback for any of these topics:

  • Website features/issues
  • Content errors/improvements
  • Missing products/categories
  • Product assignments to categories
  • Search results relevance

For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.

Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.

Makers love reviews as much as you do, please follow this link to review the products you have purchased.