Search results for: 'steel brackets'

While this incredibly robust Steel U-Bracket rocks the same height, width, and 2.5mm thickness of a 1-hole length of 1120 Series U-Channel,.....

Often times used to attach a threaded component to the slot on the side of goRAIL. This 7-hole bracket reaches out past the standard 32mm.....

A multitool among goBILDA® brackets, these 1-Hole Threaded Steel L-Brackets offer essential versatility with their countless possibilities.....

This Steel U-Bracket is a dimensional sibling to the 1-hole length of 1120 Series U-Channel. It differs only in its steel construction and.....

This steel angle pattern mount is an excellent solution for robust 90° joints as well as miter gear assemblies. And thanks to the.....

This Threaded Steel L-Bracket can be used as a robust 90° connector, as well as to create a linear junction between lengths of U-Channel......

This 2501-0001-0002 Pulley Bracket is designed for use with the 2500-0014-0336 Viper Slide. This pack includes four pulley brackets and.....

This Threaded Steel L-Bracket can be used as a robust 90° connector or as reinforcement to an existing junction. Both sides have three.....

This steel 90° bracket is a sturdy solution for right angles in your project. Its 16mm goBILDA pattern thru-holes not only surround.....

A 1-1 1137 Series Steel Flat Grid Bracket (2-pack)

A 1-2 1137 Series Steel Flat Grid Bracket (2-pack)

This steel 90° bracket is a sturdy solution for right angles in your project! The two primary thru-holes (located at 90° to one.....

A 2-1 1137 Series Steel Flat Grid Bracket (2 Pack)

This coated steel bracket lets you securely mount typical NEMA 23-size stepper motors to your project. The bracket features two slots for various mounting...

This bracket was designed specifically for the Glideforce Medium-Duty (MD) linear actuators. It is made from stamped, zinc-plated steel and has been...

This bracket was designed specifically for the Glideforce Industrial-Duty (ID) linear actuators. It is made from stamped, black powder coated steel and...

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 7.4 V, allowing for a holding torque of 9 kg-cm (125 oz-in).

This bracket was designed specifically for the Glideforce Light-Duty (LD) linear actuators. It is made from stamped, zinc-plated steel and has been tested...

The FTC Starter Kit is comprised of a massive amount of individual pieces with a retail value of over $1,651! But FTC Team budgets are...

A 2-1 1108 Series Flat Pattern Bracket

This tensioner bracket is excellent for taking up that extra bit of slack when working with round belts, timing belts or chains. The slot...

The FTC Starter Kit is comprised of a massive amount of individual pieces with a retail value of over $1,445! But FTC Team budgets are...

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 2 A at 4.5 V, allowing for a holding torque of 14 kg-cm (190 oz-in).

This NEMA 23-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 2.8 A at 2.5 V, allowing for a holding torque of 13 kg-cm (180 oz-in).

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 8.6 V, allowing for a holding torque of 14 kg-cm (190 oz-in).

This 4mm bore set-screw hub allows you to rotate a gear, sprocket, pulley, bracket or beam via a 4mm diameter round shaft. Its steel.....

This 6mm bore set-screw hub allows you to rotate a gear, sprocket, pulley, bracket or beam via a 6mm diameter round shaft or 6mm diameter.....

This 3mm bore set-screw hub allows you to rotate a gear, sprocket, pulley, bracket or beam via a 3mm diameter shaft. Its steel construction.....

This ¼” bore set-screw hub allows you to rotate a gear, sprocket, pulley, bracket or beam via a ¼” diameter shaft. Its steel construction.....

This 5mm bore set-screw hub allows you to rotate a gear, sprocket, pulley, bracket or beam via a 5mm diameter shaft. Its steel construction.....

A 200mm long Stainless Steel Threaded Rod

A 8mm long aluminium spacer with an inner diameter of 12mm

A 6mm long M4 Socket screw made from zinc-plated steel.

A 2mm long aluminium spacer with an inner diameter of 8mm

A 3x7 1139 Series Grid Plate

A 6mm Bore 1602 Series 1-Side, 2-Post Pillow Block

We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and is hand picked only at the peak of the season. Or how they are expertly hand-ground by a 6th generation master grinder. And how every nut passes a rigorous 19-point inspection process at each step of the process. And how each nut’s dimensional variations can only be measured on the sub-atomic level.

These 0.5mm thick stainless steel shims are intended to provide a small amount of necessary space between components in your assembly. .....

A 6mm Bore 1606 Series 2-Side, 1-Post Pillow Block