Search results for: 'arduino cable'

Unplugging USB devices just to remove power is a thing of the past with this handy little microUSB extender.

Grove is a convenient plug-and-play system with the specialized interface, but that doesn't mean it couldn't be used in an open ecosystem like a breadboard

The Gravity 4Pin IIC/I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 30cm length. One side is PH2.0-4p connector and the other side is XH2.54...

Extend your servo's reach with this 1m Servo Extension Cable. Featuring male and female JR Style connectors, it's perfect for robotics, RC vehicles, and other DIY/Maker projects. Enjoy seamless connections and added flexibility in cable management – a must-have for any enthusiast's toolkit.

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded.

This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact. Functionality has remained the same.

Just about all electronics use a UART serial port with RX and TX pins for debugging, bootloading, programming, serial output, etc. But it's rare for a computer to...

This is a simple jumper adapter cable that comes pre-terminated with a female JST connector on one end and a breadboard hookup pigtail on the other. This cable makes it easy to connect components with a JST connector to a breadboard or an Arduino-based device’s pins.

Are you a maker in the midst of a STEMMA dilemma? This 100mm long cable is a fantastic chimera-cable fitted with STEMMA QT 4-pin JST SH on one end, and Arduino MKR...

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when putting an Arduino...

A compact time-of-flight proximity sensor to accurately measure distances.

This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more “Beefy” voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.

Connect this to that with an IDC cable! This cable has 6 pins (2x3) in 0.1"x0.1" spacing. Often used for programming AVRs. 6" long with two sockets crimped onto...

Three push buttons (plus three orange LEDs) for interactive projects, menu navigation or quick control inputs.

The SparkFun 3.3V FTDI Starter Kit gives you just what you need to get started with FTDI FT232RL USB to serial IC. The pinout of the included board matches the FTDI...

This here is your standard A to micro-B USB cable, for USB 1.1 or 2.0. Perfect for connecting any development board, microcontroller, mobile phone, or other device...

What do you do if you find that the line length is not enough when you do a project with Boson Kit? Or you find out the interface of Boson module is not matched...

As technology changes and adapts, so does Adafruit. This USB Type A to Type C cable will help you with the transition to USB C, even if you're still totin' around...