Search results for: '1.5 mm'

Gracefully hold 18650 batteries with these durable ABS holders.

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection.

These switchmode plugpack adaptors are slim in size, lightweight, and feature manually selectable variable voltage outputs

This female to male DC power cable offers an easy solution for extending the length of a DC power supply.

This compact (0.6"×0.6") switching step-up (or boost) voltage regulator efficiently generates 5 V from input voltages as low as 1.3 V and handles...

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays.

These small tubes can be threaded on to a wire to provide RF or interference suppression at frequencies higher than the normal operating range of the equipment to be protected.

Convert 3.5mm plug to AV Stereo with this 1.5m cable

Used along with the solder sucker to clean up soldering messes. Wick really comes in handy when soldering or desoldering surface-mount parts. Even if you don't have...

These solid 1.25mm pitch connector cable pairs are great when you need something that can carry a couple amps of current and are easy to connect and disconnect.

Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out. Adafruit like this wire for being extremely supple and flexible, so it is great for wearables or projects where the wire-harness has to be able to deal with a lot of bending.

This connector is a single-row, 9-pin, right-angle female header strip designed to match 0.1" male headers. The order quantity must be a multiple of two.

There’s nothing worse than getting ready for a good hack and then realizing that you can’t even get the box open because you don’t have the right screwdriver. Sure, we all have a few Phillips-head drivers and maybe a few slotted drivers but what about Torx, Hex Socket or Tri-Wing? This kit has them all. Along with a large variety of interchangeable bits and a hard ABS plastic handle, the kit also includes a steel extension bar and a flexible extension neck that really comes in handy when you’re hacking in tight spaces. The plastic case keeps everything secure and organized with labeled sockets for each bit.

A 2mm long aluminium spacer with an inner diameter of 6mm

When 0.1" is too big, and JST PH's too chunky, this ultra-slim 1.25mm connector cable is a reliable alternative. These are 1.25mm pitch but have a nice clicky connection.

These 2×5-pin housings work with Pololu's wires with pre-crimped terminals to let you quickly make custom cables that mate with various 0.1"-spaced connectors, including male or female headers and solderless breadboards. They are sold in packs of 5.

This connector is a single-row, 2-pin, straight female header strip designed to match 0.1" male headers. The order quantity must be a multiple of five.

This fully-assembled pan-tilt kit is the perfect way to give your project full range motion with two micro servos. The pan-tilt can rotate roughly 180° from side-to-side...

These nine-pin housings work with Pololu's wires with pre-crimped terminals to let you quickly make custom cables that mate with various 0.1"-spaced connectors, including male or female headers and solderless breadboards. They are sold in packs of 5.

This force-sensing resistor (FSR) from Interlink Electronics is a passive component that exhibits a decrease in resistance when there is an increase in the force applied to the 1.5″ × 1.5″ (4 cm × 4 cm) active area, allowing you to create a sensor that is able to detect force or pressure. With a force sensitivity range of a few grams to a few kilograms, this sensor is optimized for use in human touch control applications.

Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wire wimps out. Adafruit like this wire for being extremely supple and flexible, so it is great for wearables or projects where the wire-harness has to be able to deal with a lot of bending.

These 20 mm long aluminum adapters convert a 6 mm diameter shaft to a 12 mm hex shaft that is compatible with many common hobby RC wheels. The set includes two adapters, two M4 screws for securing wheels to the adapters, four M3 set screws for securing the adapters to motor shafts, and one 1.5 mm Allen wrench for use with the set screws.

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. Adafruit use them by the dozen for making...

This connector is a single-row, 8-pin, straight female header strip designed to match 0.1" male headers. The order quantity must be a multiple of two.