ModMyPi MCP23017 pHAT - 16 Channel I/O Expansion (Zero)

SKU: CE05840 Brand: ModMyPi

Retired Product

Replaced by: CE07494

This product has been replaced by: CE07494
This product is no longer available. This page is only for reference.

The MCP23017 pHAT from ModMyPi is the perfect I/O expansion pHAT for your Raspberry Pi Zero. The pHAT features a single removable MCP23017 DIP IC, which utilize two i2c pins (which can be shared with other devices if required), and in exchange gives your Raspberry Pi Zero an additional 16 GPIO ports! Each I/O pin can be configured as an input, output or an input with a pull-up resistor. The MCP23017 pHAT is stackable, featuring selectable i2c address jumpers which supports up to 8 independent addresses: This means you can add up to 128 additional I/O's to a single Raspberry Pi by stacking up to 8 MCP23017 pHAT's!

The MCP23017 pHAT can also be used to protect your Raspberry Pi! ModMyPi's used removable, rather than surface mount, MCP23017 DIP IC's which can act as a replaceable buffer for the Raspberry Pi's GPIO, essentially protecting your Raspberry Pi from damage via the GPIO ports. The MCP23017 pHAT is powered via the Raspberry Pi's GPIO port, but features an included (but unsoldered) terminal block for advanced users wanting to use an external 5V source, or stack multiple MCP23017 pHATs on a single Pi. The isolation jumper "PWR JUMPER" must be removed when using an external source.

The product comes fully assembled with the push-fit "plug & play" Single Shroud Header, Socket Header, and 14mm HAT Mounting Kit, so there's no soldering required, and you can get started in no time with ModMyPi's Wiki & Example Code!

Please Note. The external power terminal block is NOT soldered onto the board and is designed for advanced users only.

Features

1 x MCP23017 IC
Removable & Replaceable DIP Packaged IC's - If you damage one, simply replace!
Selectable i2c Address Jumpers - Supports up to 8 Independent Addresses
16 Port GPIO Expander Board with Configurable I/O's (Input/Output/Input w/ Pullup)
Jumper Isolated Terminal Block 5V Input
Stackable (Up for 8 MCP23017 pHATs, and up to 128 I/O's)
pHAT Compliant

Contains

1 x Fully Assembled MCP23017 pHAT with 1 x MCP23017 IC
1 x Mounting Kit: 4 x M2.5 14mm F/F Stand-offs & 8 x M2.5 5mm Bolts
1 x 40 Pin "Single Shroud" Header
1 x Unsoldered Two Point Screw Terminal Block

MCP23017 Features

16 bit remote bidirectional I/O port
High-speed I2C interface
Three hardware address pins to allow up to eight devices on the bus
Configurable interrupt output pins - active-high, active-low or open-drain
INTA and INTB can be configured to operate independently or together
Configurable interrupt source - based on input changes, so you don't need to keep polling the chip
Polarity Inversion register to configure the polarity of the input port data
External Reset input
Low standby current: 1μA max.

MCP23017 Specifications

Bus Frequency: 1.7MHz
Chip Configuration: 16bit
IC Interface Type: I2C, Serial
Interface Case Style: DIP
No. of I/O's: 16
No. of Pins: 28
Supply Voltage Max: 5.5V
Supply Voltage Min: 1.8V

Downloads

This product is listed in:

Retired

Product Comments

Start the conversation

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

$3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
$6+ for Standard Post (typically 6+ business days, tracked)
$10+ for Express Post (typically 2+ business days, tracked)
Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

$11+ for Pack and Track (3+ days, tracked)
$16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review