ESP32-C6-DevKitC-1-N8 Development Board (8 MB SPI Flash)

SKU: DFR1054 Brand: DFRobot

The ESP32-C6-DevKitC-1 development board is a powerful IoT development board that integrates Wi-Fi, Bluetooth LE, Zigbee, and Thread functions, making it...

$23.25 AUD, inc GST

$21.14 AUD, exc GST

In stock, ships same business day if ordered before 2PM
Delivered by Tue, 7th of Apr

Quantity Discounts:

6+ $20.08 (exc GST)
12+ $19.24 (exc GST)

ESP32-C6-DevKitC-1 is an entry-level development board based on ESP32-C6-WROOM-1, a general-purpose module with an 8 MB SPI flash. This board integrates complete Wi-Fi, Bluetooth LE, Zigbee, and Thread functions. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing, so developers can either connect peripherals with jumper wires or mount ESP32-C6-DevKitC-1 on a breadboard as per their needs. The board can be used in applications such as smart home, industrial automation, health care, consumer electronics, service robots, and IoT data loggers.

ESP32-C6-DevKitC-1 is built around ESP32-C6, a RISC-V 32-bit single-core CPU that operates at up to 160 MHz, and integrates a rich set of peripherals. Users can power off the CPU and make use of the low-power co-processor to constantly monitor the peripherals for changes.

ESP32-C6-DevKitC-1-N8 Development Board Components

Figure: Components

Key Component	Description
ESP32-C6-WROOM-1	ESP32-C6-WROOM-1 is general-purpose module supporting Wi-Fi 6, Bluetooth 5, and IEEE 802.15.4 (Zigbee 3.0 and Thread). It's built around the ESP32-C6 chip, and comes with an 8 MB SPI flash. ESP32-C6-WROOM-1 uses on-board PCB antenna. For more information, see ESP32-C6-WROOM-1 Datasheet.
Pin Header	All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board.
5 V to 3.3 V LDO	Power regulator that converts a 5V supply into a 3.3V output.
3.3 V Power on LED	Turns on when the USB power is connected to the board.
USB-to-UART Bridge	Single-chip USB-to-UART bridge provides transfer rates up to 3 Mbps.
ESP32-C6 USB Type-C Port	The USB Type-C port on the ESP32-C6 chip is compliant with USB 2.0 full speed. It is capable of up to 12 Mbps transfer speed (Note that this port does not support the 480 Mbps high-speed transfer mode).
Boot Button	Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.
Reset Button	Press this button to reset the system.
USB Type-C to UART Port	Used for power supply to the board and the communication with the ESP32-C6 chip via the on-board USB-to-UART bridge.
RGB LED	Addressable RGB LED, driven by GPIO8.
J5	Used for current measurement. See details in Section Current Measurement.

Block Diagram of ESP32-C6-DevKitC-1-N8 Development Board

Figure: Block Diagram

Pin Header: The two tables below provide the Name and Function of the pin headers on both sides of the board (J1 and J3). The pin header names are shown in the figure of ESP32-C6-DevKitC-1 Layout.

J1 Pin Layout of ESP32-C6-DevKitC-1-N8 Development Board

Figure: J1 Pin Layout

J3 Pin Layout of ESP32-C6-DevKitC-1-N8 Development Board

Figure: J3 Pin Layout

Pin Layout of ESP32-C6-DevKitC-1-N8 Development Board

Figure: Pin Layout

The differences between ESP32-C6-DevKitM-1 and ESP32-C6-DevKitC-1-N8

The ESP32-C6-DevKitM-1 is based on the ESP32-C6-MINI-1 (U) module, which has a 4 MB SPI flash, while the ESP32-C6-DevKitC-1-N8 is equipped with the ESP32-C6-WROOM-1 module, which has an 8 MB flash.

The amount of flash memory can affect the amount of data that can be stored on the board and the complexity of the programs that can be run on it.

Applications

Smart home
Industrial automation
Health care
Consumer electronics
Service robots
IoT data loggers

Specification

Processor: ESP32-C6 chip, RISC-V 32-bit single-core
ROM: 320 KB
SRAM: 512 KB HP SRAM 16 KB LP SRAM
Integrated 40 MHz crystal oscillator
8 MB SPI flash
Support Thread 1.3
Support Zigbee 3.0
Operating voltage/Supply voltage: 3.0-3.6 V
Recommended operating temperature range: –40 to 85°C

Documents

Parts List

ESP32-C6-DevKitC-1-N8 Development Board × 1

This product is listed in:

Wireless>Wifi>Microcontrollers

Product Comments

Start the conversation

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

$3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
$7+ for Standard Post (typically 6+ business days, tracked)
$11+ for Express Post (typically 2+ business days, tracked)
Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

$12+ for Pack and Track (3+ days, tracked)
$16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

40 Aruma Place
Cardiff
NSW, 2285
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!