Search results for: 'pad'

This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand, it's just a...

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.

This is hot! Literally! Apply 5-12VDC and the stainless steel fibers in this heating fabric will warm up, creating a little heating pad. On one hand, it's just a...

This is a 10 pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are perfect for short-term monitoring of Neurofeedback and Biofeedback purposes. They are to be used once and are very handy because of integrated, latex-free gel. Each pad adheres very well to the skin and the snap connector can be pushed on or removed from the electrode lead with no issue.

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.

The SparkFun Qwiic Directional Pad adds a 5-way directional pad to your I2C bus!...

Beguiled by a fancy new chip that is only available in a SOIC or (T)SSOP pinout? This breakout PCB set will make your life much much easier and get you prototyping...

The 4x4 Keypad is a general purpose 16 button (4x4) matrix keypad. It comes ready to work, simply peel-off the adhesive backing, stick it to your surface and plug it in.

Protect the finish of your project with these add-on Jaw Pads. For for 201, 203, 207 and 209

Now, it is time to add a more fancy interactive way to your project. This DFRobot touch kit comes with three types touch sensors. An ipod styple wheel touch, a keypad touch which supports backlit and a grid touch pad which can recoginze something unique.

This is a translucent silicon rubber button pad with 16 buttons originally inspired by the folks at monome.org. Each button has a hole underneath that accepts either a 3mm or 5mm standard LED. The idea is that you can create a button interface of your choice with the ability to display simple colors under each button. Mainly, we wanted to use our tri-color LEDs to create a full RGB color for each button.

This is a translucent silicon rubber button pad with 4 buttons orignally inspired by the folks at monome.org. Each button has a hole underneath that accepts either a 3mm or 5mm standard LED. The idea is that you can create a button interface of your choice with the ability to display simple colors under each button. Mainly, we wanted to use our tri-color LEDs to create a full RGB color for each button.

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possible to reduce the deflection of the pad.

This Felt Padding is for if you want extra cushioning for your DIY keeb. This is specifically designed for the common "GH60" / 60% keyboard...

This a simple breakout board for the button pads. Each LED and button is brought out to the side connectors. The connectors are soldered to the back side of the PCB. We recommend trimming the connector leads on the button side as short as possible to reduce the deflection of the pad.

This cleaning pad has just the right amount of abrasion for cleaning your PCB board after milling. We have testest this scouring pad extensively with our Bantam Milling Machine finding it to clean away any burr's whilst leaving the copper board with a smooth finish with no scratch marks.

This is a small, 5-way directional pad. When connected to a microcontroller, push the 5-way tactile switch toward a direction (up, down, left, right, or...

Keybow MINI is a 3-key version of Pimoroni's wildly-popular Keybow mini mechanical keyboard. Like its older sibling, Keybow MINI has RGB-illuminated, hot-swap, mechanical switches, and clear key caps. It's the perfect way to add a tiny macro pad to your desk, or to use as a little osu! controller.

PGY TECH 110CM Landing Pad for Drones

This breakout board is the simplest way to create a project with mutiple capacitive touch sensors. No microcontroller is required here - just power with 1.8 to 5.5VDC...

For the times when you need to jot down a few thoughts or diagrams but don't necessarily need a whole honkin' spiral notebook, ...

This antistatic mat & kit is ideal to prevent any static discharges when working on your next electronics project.

Repair your torn or damaged vacuum base pad!

Repairs can be tough. You don't need missing screws making it worse. iFixit designed this mat to make repairs easier. You won’t lose screws and won’t forget which...

This flexible pocketed mat is perfect to insert any of the pre-made cards such as the Australian Resources.

This transparent pocket mat allows you to place cards, images or other flat objects into the pockets to further enhance your Bee-Bot or Blue-Bot adventures

The SparkFun ProtoShield Kit lets you customize your own Arduino shield using whatever circuit you can come up with and then test it to make sure everything is working...

The Adafruit Proto Under Plate PiCowBell is intended to be treated like a mini solder-less proto plate to simplify programming and sensor connectivity for...

A minimal but powerful RP2350 breakout board modelled on a Pin Grid Array, with the maximum exposed pins crammed into the smallest possible space...