Home
Shop
Retired
Blend V1.0 - a single board integrated with Arduino and BLE (Seeed Studio)

Skip to the beginning of the images gallery

Blend V1.0 - a single board integrated with Arduino and BLE (Seeed Studio)

SKU: SS113030018 Brand: Seeed Studio

Retired Product

Search for an alternative

This product has been retired. It is no longer available, but this page has been kept for reference.

Blend is an integrated developement board, we have "blend"ed Arduino with Bluetooth 4.0 Low Energy (aka BLE or Bluetooth Smart) into a single board. It is targeted for makers to develop low power Internet-Of-Things (IoT) projects quickly and easily.

Blend is 100% compatible with sketches and Shields that work with Arduino Leonardo. The micro-controller unit (MCU) is Atmel ATmega32U4 and the BLE chip is Nordic nRF8001. Blend runs as BLE peripheral role only, it allows BLE central role devices to establish connection with.

Current supported BLE central devices:

iOS 7

•iPhone 4s

•iPhone 5 (all models)

•iPod touch 5

•iPad 3/4/mini/Air

Android 4.3 or above (4.4 recommended for stability) with Bluetooth 4.0 hardware support

•Nexus 4

•Nexus 5

•Nexus 7

•(please report any other Android devices supported)

Windows Phone 8.1

•Nokia Lumia 630

•(please report any other Windows Phone devices supported)

Windows 8.1 with built-in Bluetooth 4.0 or USB dongle

Mac OSX 10.9.2 with built-in Bluetooth 4.0 or USB dongle

Linux with BlueZ 5.1 with built-in Bluetooth 4.0 or USB dongle

Features

UtilizeNordic Bluetooth Smart SDK for Arduino
Software development using Arduino IDE
Works with our free Android AppandiOS App
Support 5V and 3.3V operating voltage
Selectable REQN and RDYN pins, from pin 0 to 3, 6 to 11
Flexible RF RESET pin, pin 4 or 5
Over-the-Air download of sketch to Blend (available soon)
Besides the on-board PCB antenna, option to use SMA connector for external antenna (soldering is required)

Specification

Microcontroller	Atmel ATmega32U4
Wireless Chip	Nordic nRF8001
Operating Voltage	3.3V or 5V
Input Voltage	5V (USB) 6.5-12V (DC input or VIN)
	Note: Use only one power source at a time, otherwise you will damange the board.
Clock Speed	16MHz
Connectivity	Bluetooth 4.0 Low Energy micro-USB Serial (TX/RX) I2C SPI
Flash Memory	32KB (of which 4 KB used by bootloader)
SRAM	2.5KB
EEPROM	1KB
Dimensions	73 x 54 x 12mm (120 x 73 x 25mm with packaging)
Weight	19g (37g with packaging)
I/O Pins	20

How It Works

The nRF8001 chip communicates with ATmega32U4 through the ACI (Application Controller Interface). The ACI is similar to SPI but not actually works as SPI. SPI is consist of MOSI, MISO, SCK and SS, whereas ACI is consist of MOSI, MISO, SCK, REQN and RDYN.

Since the nRF8001 chip may receive data anytime even not selected by SPI master (Atmega32U4), so the SS line is not needed.

For the ACI, data exchange still through MOSI and MISO, and SCK provides the clock generated by master.

When master wants to request data from BLE Shield, it puts the REQN to low until RDYN line is put to low by BLE Shiled, and then master generates the clock to read out the data. After reading out the data, master will release the REQN and BLE Shield release the RDYN, put them to high.

If the nRF8001 has data to transmit to master, it will put the RDYN to low to indicate master, even though the master has not requested data and REQN is idle. If the master detectes a low level condition on RDYN, it will put REQN to low and generate the clock to read out the data. After reading out the data, both REQN and RDYN will be put to high. Note that REQN is controlled by master while RDYN is controlled by the nRF8001 chip.

Operate at 3.3V or 5V

According to the Atmega32U4 specification, the MCU can run at either [email protected] or 16MHz@5V. Normally, you should set the voltage selection switch to 5V to run the board at 16MHz. However if you need to connect to shields or external components, such as sensors or MCU, which accept 3.3V only, you should change the operating voltage to 3.3V using the voltage selection switch.

Note that while Blend is running at 3.3V, the Atmega32U4 will still run at 16MHz which is outside Atmel's specification, the CPU is overclocked (we have not seen any issue so far).

Support

For questions about Nordic Bluetooth low energy SDK for Arduino, please visit Nordic Developer Zone.

All other questions regarding Blend, please visit our Blend Forum.

This product is listed in:

Retired

Product Comments

Start the conversation

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

$3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
$6+ for Standard Post (typically 6+ business days, tracked)
$10+ for Express Post (typically 2+ business days, tracked)
Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

$11+ for Pack and Track (3+ days, tracked)
$16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

Unit 18, 132 Garden Grove Parade
Adamstown
NSW, 2289
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review