Search results for: 'Solarbotics GM2 224:1 Gear Motor Offset Output'
- 228:1 Plastic Gearmotor, Offset OutputSKU: POLOLU-1118 Brand: PololuThis 228:1 gearbox with brushed DC motor has a low-current motor and provides power and speed that is comparable to an RC servo at a fraction of the cost. At 6 V, it has a free-run speed of 45 RPM and a stall torque of approximately 100 oz-in. Though the product picture shows two gearmotors, this product is for a single motor.Special Price $13.66 AUD, inc GSTRegular Price $16.07 AUD, inc GSTDelivered by May 2nd
- Solarbotics GMW (GM2/3/8/9 Gear Motor Mount - ONE mount)SKU: POLOLU-601 Brand: PololuThis sturdy plastic wheel for the GM2, GM3, GM8, and GM9 gearmotors can also be used as a wheel adapter for other wheels or as a mount for other mechanisms via four mounting holes. The wheel also fits on Pololu plastic gearmotors.Special Price $2.32 AUD, inc GSTRegular Price $2.73 AUD, inc GSTDelivered by May 2nd
- Hobby Motor - GearThis is our new Hobby Motor now with a 6mm, 10 tooth, gear to make your basic projects a little simpler to manage. It works well for basic things like making a fan or spinning something pretty fast without much resistance.$3.75 AUD, inc GSTAs low as $3.56 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- 180:1 Mini Plastic Gearmotor, Offset 3mm D-Shaft OutputSKU: POLOLU-1594 Brand: PololuThis compact, inexpensive plastic gearmotor (brushed DC motor with a 180:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range. The gearbox has a 0.38″-long, 3 mm-diameter D-shaped output shaft that is offset from but parallel to the motor shaft, and a built-in safety clutch helps protect the gears from excessive loads. Key specs at 4.5 V: 80 RPM and 80 mA free-run, 30 oz-in (2.2 kg-cm) and 0.8 A stall.$10.50 AUD, inc GSTAs low as $9.98 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- Solarbotics RM2 (high-power motor for GM2/3/8/9)SKU: POLOLU-611 Brand: PololuNeed more power out of your gear motor? This is a high-power brushed DC motor that fits in the same form factor as used by the GM2/3/8/9 style gear motors.
- Bipolar Stepper Motor with Planet Gear Box (18kg.cm)SKU: FIT0349 Brand: DFRobot
This is a bipolar stepper motor with a planetary gearbox (gear ratio: 5.18) and uses a standard 8mm-diameter D type output shaft, with a 1.8° step angle (200 steps/revolution).
- Hobby Motor with Encoder - Metal Gear (DG01D-E)SKU: ROB-16413 Brand: SparkfunThe DG01D-E is a single hobby motor with a hall speed encoder. This motor requires a voltage between 3-9V, has a gearbox ratio of 1:48 and a speed of 90RPM at 4.5V...
- Turbo Metal Gear Worm Motor (6V 40RPM 10kg/cm)SKU: FIT0489-B Brand: DFRobotThe turbo metal gear worm motor uses a metal gear box for durability and a high torque output. Due to the special mechanical structure of the worm drive the motor output shaft is self locking and can not be rotated.
- Turbo Metal Gear Worm Motor (6V 160RPM 2.8kg/cm)SKU: FIT0489-A Brand: DFRobotThe turbo metal gear worm motor uses a metal gear box for durability and a high torque output. Due to the special mechanical structure of the worm drive the motor output shaft is self locking and can not be rotated.
- Turbo Metal Gear Worm Motor (12V 40RPM 8kg.cm)SKU: FIT0489-D Brand: DFRobotThe turbo metal gear worm motor uses a metal gear box for durability and a high torque output. Due to the special mechanical structure of the worm drive the motor output shaft is self locking and can not be rotated.
- Turbo Metal Gear Worm Motor (12V 160RPM 2.2kg.cm)SKU: FIT0489-C Brand: DFRobotThe turbo metal gear worm motor uses a metal gear box for durability and a high torque output. Due to the special mechanical structure of the worm drive the motor output shaft is self locking and can not be rotated.
- DC Micro Metal Gear Motor w/Driver - 50:1SKU: DFR0429 Brand: DFRobotAn ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecting it to the MCU and learning the relevant electronic theory can be confusing and frustrating when you just need something to work quickly. We hope that using the DC Micro Metal gear motor changes this.$22.45 AUD, inc GSTAs low as $21.33 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- DC Micro Metal Gear Motor w/Driver - 30:1SKU: DFR0430 Brand: DFRobotAn ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of finding the right motor driver, connecting it to the MCU and learning the relevant electronic theory can be confusing and frustrating when you just need something to work quickly. We hope that using the DC Micro Metal gear motor changes this.
- Hobby Motor with Encoder - Plastic Gear (Pair, Red)SKU: ROB-24053 Brand: SparkfunThe motor requires a voltage between 4.5-9V, has a gearbox ratio of 1:48 and a speed of 140RPM at 4.5V...$38.14 AUD, inc GSTAs low as $36.23 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- TT Motor Bi-Metal Gearbox - 1:90 Gear RatioSKU: ADA3801 Brand: AdafruitThese durable (but affordable!) gearbox motors (also known as 'TT' motors) are an easy, low-cost way to get your projects moving. This is a TT DC Bi-Metal Gearbox...
- TT Motor All-Metal Gearbox - 1:90 Gear RatioSKU: ADA3802 Brand: AdafruitThese durable (but affordable!) gearbox motors (also known as 'TT' motors) are an easy, low-cost way to get your projects moving. This is a TT DC All-Metal Gearbox...
- Devastator Tank Mobile Platform (Metal DC Gear Motor)SKU: ROB0128 Brand: DFRobotThe Devastator tank platform is constructed from high strength aluminium alloy and is extremely solid and durable. Due to the popularity of this platform we have released a new and improved version 2 that includes the following features:
- Solarbotics Squid Hunting CarouSol KitSKU: CE05946 Brand: SolarboticsExplore the fusion of art and science with Solarbotics Squid Hunting CarouSol Kit: an intricate solar-powered display of a steampunk submarine and a giant squid. Harness SolarEngine technology for an eco-friendly educational experience, perfect for hobbyists and STEM enthusiasts.
- Vibration Motor 11.6×4.6×4.8mmSKU: POLOLU-2265 Brand: PololuThis tiny DC motor has a shaft with an offset mass that vibrates when it rotates. Motors like this are commonly found in cell phones and other devices that use vibration for tactile feedback. The motor has 1.5″ leads and is encased in a removable rubber sleeve that gives it flat surfaces for mounting and prevents it from chattering against whatever it is mounted to. It is intended for operation around 3 V (2.4 V to 3.5 V recommended).
- Stepper Motor with CableThis is a simple, but very powerful stepper motor with a 4-wire cable attached.
- N20 DC Motor with Magnetic Encoder - 6V with 1:100 Gear RatioSKU: ADA4639 Brand: AdafruitThe first step in a robotics project is to get a motor spinning. Once you've done that you quickly learn that not all motors go the same speed, even if they are the same part number! There are always variations that relate to voltage, environment, and manufacturing changes. So, the second step is to figure out how fast it's going!
- N20 DC Motor with Magnetic Encoder - 6V with 1:298 Gear RatioSKU: ADA4641 Brand: AdafruitThe first step in a robotics project is to get a motor spinning. Once you've done that you quickly learn that not all motors go the same speed, even if they are the same part number! There are always variations that relate to voltage, environment, and manufacturing changes. So, the second step is to figure out how fast it's going!
- N20 DC Motor with Magnetic Encoder - 6V with 1:50 Gear RatioSKU: ADA4638 Brand: AdafruitThe first step in a robotics project is to get a motor spinning. Once you've done that you quickly learn that not all motors go the same speed, even if they are the same part number! There are always variations that relate to voltage, environment, and manufacturing changes. So, the second step is to figure out how fast it's going!
- N20 DC Motor with Magnetic Encoder - 6V with 1:150 Gear RatioSKU: ADA4640 Brand: AdafruitThe first step in a robotics project is to get a motor spinning. Once you've done that you quickly learn that not all motors go the same speed, even if they are the same part number! There are always variations that relate to voltage, environment, and manufacturing changes. So, the second step is to figure out how fast it's going!$26.85 AUD, inc GSTAs low as $24.97 AUD, inc GST
Out of Stock
Sign up to get notified when it's available to order.
- Gravity: N20 Micro Metal Gear Motor with Integrated Drive (3V-6V, 1:150/133RPM)SKU: DFR1114 Brand: DFRobotGravity: N20 Miniature Metal Motor is a simplified motor control with integrated drive, PWM servo control, and low power consumption. Ideal for robots,...Special Price $18.20 AUD, inc GSTRegular Price $23.23 AUD, inc GSTAvailable with 7 to 10 day lead time
Solarbotics Paris Flyer CarouSol Kit Speed Build
We had a lot of fun making this speed build video for the Paris Flyer CarouSol Kit by Solarbotics. If you aren't already familiar, Solarbotics makes a great line of DIY electronics kits made from laser cut materials. They range from quite s...
Motor Drivers vs. Motor Controllers
If you’ve ever built a robot with wheels, or any motorised parts really, you’ll have come across the issue of needing to drive it from your microcontroller. Because a standard chip is only able to output a small amount of curren...
DC Motor Control with an Arduino
Electronics is fun, so far we have covered off on communicating between devices, making LEDs flash and LCD screen operation. However using electricity to control some form of movement in your project is a fun and interesting aspect to inves...
How To Control A Motor with the Raspberry Pi
In this tutorial, we are going to connect a Motor to the Raspberry Pi and create a hypnotic self-spinner. We are first going to look at how to wire the Raspberry Pi to the motor controller and the motor. We will then look at using the raspb...
Makerverse Motor Driver, 2 Channel - Application Guide
Introduction The Makerverse Motor Driver has been updated to a v20 design which now features a 5V output pin instead of the VM pin. Some images and in-video descriptions in this guide may be outdated This guide covers the use of the Maker...
How to use Stepper Motors and DC Motors with a Raspberry Pi - Adafruit DC & Stepper Motor HAT
This guide will demonstrate exactly how to control Standard Stepper Motors and DC Motors with a Raspberry Pi Single-Board Computer. To do this as seamlessly as possible we will utilise a HAT. HAT stands for Hardware Attached on Top. HAT bo...
Servos, Steppers or Solenoids? | Choosing an Actuator to Move Your Project
In this guide, we go over some common ways of adding motion to your project with actuators such as stepper motors, servos and linear actuators, to help you choose which one is most appropriate for your situation. The start of this guide c...
Layer Heights when Resin 3D Printing | Accurate 28mm Scale Models or Maximum Printer Output
Speed or Perfection? That choice is what an understanding of Layer Heights whenever Resin 3D printing is going to provide you. Any Traditional Resin 3D Printer worth its salt will let you print with Layer Heights between 10 Micron to 100 Mi...
Arduino Projects with Robotics Using the Sparkfun RedBoard
Welcome to the final Project Set of the Sparkfun Inventors Kit! This Project Set focuses on Robotics with the final Circuit being an Autonomously Driving Vehicle! New components introduced in this tutorial are: DC Motor/Gearbox Mo...
Using Relays with Particle
So, you want to control things with your Particle Photon and/or Electron do you? Well, a relay is a perfect way to do that. Whilst there are many ways to control an electrical signal from digital logic such as transistors and optoisolators,...
Control Large GoBILDA DC Motors With a Raspberry Pi - Pololu Motoron HAT
This guide will demonstrate exactly how to control any large DC Motors that we stock with a Raspberry Pi Single Board Computer, through code or through a Bluetooth Controller. To clarify (in my mind) a large DC Motors runs at 12+ Volt...
Our Siglent SDG1032X Arbitrary Function Generator Review
Let's take a look at the new Siglent SDG1032X Arbitrary function generator. We're looking at yet another example of the closing gap between hobbyist and pro gear - the growing feature set and capabilities of entry-level equipment continues ...
Getting Started with Saleae: Tips and Tricks
Well hello there, if you’ve been looking at the amazing line-up of Saleae gear and wondered how to get started with it all, then you’ve come to the right place. Today we’re going to take a look at getting your Saleae setup...
Never Have Filament Grinding Again - Ultimaker
Filament grinding is very unlikely to occur if your running an Ultimaker S5 3D Printer with Ultimaker materials or 3rd party supported materials. Filament grinding occurs when the knurled feeder gear slips against the filament instead of sm...
How to Use Speakers and Amplifiers with Your Project
A popular question that we get all the time is ‘How do I choose a speaker or amplifier to go with my project?’. It’s a good question, and if you’re not familiar with the terminology, it can seem a bit daunting to kno...
Digital to Analogue Conversion with Raspberry Pi
Raspberry Pi right? It’s amazing! Raspberry Pi has taken the world by storm and changed the way that people think about computing. The Raspberry Pi 3 builds on this with some amazing new features, however one feature that is still ab...
How to Use DC Regulators/Converters
So, you might have the best project in the world, an amazing idea and design, but no matter how clever your circuitry or how advanced your prototype is, unless you can power your project correctly, it all counts for nothing. Often you will ...
Automating Test-Equipment with Python
The full example-code is reproduced at the bottom of this article. Performing manual measurements (in bulk) is for suckers and undergraduate students. Thankfully, most lab gear comes with a digital interface like USB or Serial and you can ...
PiicoDev Servo Driver PCA9685 | Getting Started Guide
This guide will help you get started with a PiicoDev® Servo Driver module. We'll take a tour of the module and walk through some examples to drive common servos. Servo motors are integrated motors that contain their own power circuitr...
Controlling Stepper Motors with the Arduino
Stepper Motors are a bit of a halfway mark between DC Motors and Servo motors, but they find a sweet spot that allows them to be perfect for certain applications. There are still a few main differences to be aware of when it comes to workin...
Potentiometers and the Arduino Uno
Variable resistors come in all shapes and sizes, and they all do the same basic job. They allow you precisely control voltage/current flow within a circuit. The most common type of variable resistor we see in DIY electronics is the Potentio...
Circuit Playground Express Workshop for Educators and Beginners
Welcome to the Circuit Playground Express Workshop! This workshop is geared toward educators and coding beginners, who want to get started programming with this easy to use platform. We will go over everything you need to know to get you st...
Makerverse Load Cell Kit Guide | Measure Weights and Forces
Introduction Welcome to the guide for the Makerverse Load Cell kit. With this hardware you will be able to make a set of scales capable of measuring weights up to 3kg with a precision as low as 0.1g! To follow along you will need: ...
Arduino Projects with Motion (Using Sparkfun RedBoard)
Arduino Projects with Motion (Using Sparkfun RedBoard) Welcome to the Third Project Set from the Sparkfun Inventors Kit V4.0 Guide! In this tutorial, we will explore the operation of a Servo Motor and an UltraSonic Sensor in combination wi...
Natural Disaster Sensor Project for Micro:bit
The Micro:bit is a feature-packed development board that’s perfect for the classroom or the beginner programmer. Each Micro:bit has a built-in radio that can transmit and receive signals sent from other Micro:bits. The radio has a ran...
How to use a PiRelay HAT for Raspberry Pi - Multiple Relay Control with Voice or GUI
This guide will teach you exactly how to use a Raspberry Pi Single Board Computer to independently control 4 relays. A Relay is an electrically operated switch. This is all possible thanks to the PiRelay V2 HAT from SB Components. These re...
DIY Magnetic Encoder
The PiicoDev Magnetometer unlocks a lot of sensing abilities for your project. In this guide we'll walk through how to sense an angle with a small magnet and print the angle on a PiicoDev OLED. This guide covers what the sensor is r...
Arduino Projects with an LCD (Using Sparkfun RedBoard)
Arduino Projects with an LCD (Using Sparkfun RedBoard) Welcome to Project Set 4 in the Sparkfun Inventors Kit Guide! In this tutorial, we will look into using Liquid Crystal Displays (LCD's) to print data. This ability allows us to remotel...
Choosing a Benchtop Power Supply
If you're looking for a benchtop power supply, but you're unsure of what you should be looking for in a decent supply for your workspace, we have got you covered with this guide. We will look at the specifications to look out for in a power...
PWM Expanders for Particle
Welcome, have you had a good day? Fantastic, unless of course, you haven’t had a good day so far, in which case don’t worry, it’s about to get better! Today we’re going to be learning about adding PWM channels to...
MOSFETs for Makers: Getting Started with High-Power Control
In this guide, we’ll learn how to harness the power of MOSFET transistors to easily control higher-powered components like solenoids, motors, and Peltiers with a microcontroller. First, we will cover an easy-to-follow example using s...
What is LattePanda?
If you’ve been around electronics for a while you’ll have noticed the trend of single board microcomputers targeted at hobbyists through to industrial projects, the most popular platform being the Raspberry Pi. Now the Raspberry...
PiicoDev Potentiometer - Getting Started Guide
This guide will help you get started with a PiicoDev® Potentiometer - an intuitive input device that allows you to easily interact with your project. PiicoDev Potentiometers are available in two flavours: Rotary and Slider. We'll ...
Getting Started with Servos | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Servo is, when we might use one, how to choose a Servo, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A Positional Servo, such as the Feetech FS90 Micro Servo A Con...
Tune your First Layer - Z Offsets
Out of the box, a LulzBot 3D Printer comes tuned to perform exactly as you need it to. But over time we flash new firmwares, take our printers cross country, swap tool heads, perform cold pulls and a whole swathe of other things that could ...
How to Use Rotary Encoders
Hello and welcome to our tutorial on using rotary encoders. Today we’re going to be taking a look at what is a rotary encoder, how does it work, why we would use it over other sensory inputs and creating code to use them. Rotary encod...
What Are DotStar LEDs (APA102/SK98225)?
So in case you haven’t heard yet, digital LEDs are the go-to solution for any project that uses RGB LEDs and you want to avoid the rat's nest that ensures when using multiple RGB LEDs, each colour requiring its own connection. Digital...
Rigol DG1022 vs Siglent SDG1025 vs Siglent SDG1032X - Function Generator Shootout
In this article I'll compare three popular Arbitrary function generators. They are all about the same price point and popular among makers. The models up for review are: Rigol DG1022 (data)
...
PiicoDev Magnetometer QMC6310 - Guide for Raspberry Pi Pico
Let's get started with the PiicoDev® Magnetometer. In this guide, we'll connect the Magnetometer to our Raspberry Pi Pico, get it working as a compass, and read the magnetic field strength of a nearby magnet. Finally, we'll remix the c...
How to use a NFC Reader with Raspberry Pi
Near Field Communication (NFC) is used all and everywhere. As it stands there are over two billion NFC-enabled devices (many of them smartphones) in use today. This basically means over 20% of the world’s population has access t...
Getting Hands-on with Sensors
What good is a robot if it can’t interact with the environment around it? Sensors are the backbone of almost every electronics project as they allow your program to make decisions based on external stimuli. We’ve got sensors for...
PiicoDev Magnetometer QMC6310 - Guide for Raspberry Pi
Let's get started with the PiicoDev® Magnetometer. In this guide we'll connect the Magnetometer to our Raspberry Pi, get it working as a compass, and read the magnetic field strength of a nearby magnet. Finally, we'll remix the code to ...
Raspberry Pi vs. LattePanda
Ah, what a glorious time we live in, where we have to compare which micro-computer is going to best suit our needs. If you’ve been in the maker sphere for just a short time, you’ll be sure to have heard of Raspberry Pi the mirac...
ONESIE Family - 3D Printable Cases for Raspberry Pi 4 Model B
The ONESIE family of cases come in three distinct models; Stealth, Maker and Hats. This will be a guide introducing the ONESIE family, the 3D printable monocoque stealth cases for Raspberry Pi 4 Model B, talk about what makes them di...
Raspberry Pi Pico Workshop for Beginners
Welcome to the Raspberry Pi Pico Workshop, where you will learn everything you need to know to hit the ground running and start making your own projects with the Raspberry Pi Pico and MicroPython. This workshop is designed for complete beg...
Controlling Servo Motors with Arduino
Servo motors are extremely useful in so many different applications; it’d be good to learn how to control them! Solenoid and DC motor control have been shown already; for the most part, they are both pretty straightforward (only powe...
PLA 3D Printing Tips
PLA is Poly-Lactic Acid filament, and it's usually the go-to choice for people looking to print larger models or for longer periods of time. The important properties of the material dictate the reasons for using it; it doesn't warp at all a...
Raspberry Pi and the IQaudio DAC+ | Volumio and Raspberry Pi OS | Hi-Fi on a Ras-Pi
Flawless high-quality audio output on a Raspberry Pi Single Board Computer! All is achieved by the IQaudio DAC+ HAT. This dedicated DAC lets you enjoy high-quality, distortion-free, artifact-free, low noise, and high-bitrate audio playback...
Face and Movement Tracking Pan-Tilt System with Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS ...
Making Boxes in Fusion 360 for Laser Cutting
When making a box with a laser cutter, its entirely possible to make your design as a single flat drawing through careful planning and measurement – but who wants to do that!? This is a guide to making a box quickly and easily using F...
DIY 10W Bluetooth Speaker - No Code Needed – How to use a Bluetooth 4.2 Audio Receiver Board with Onboard Amplifier (MH-M38)
Let's turn it up to 11! Today we are getting right into Bluetooth Audio Receivers in particular the MH-M38. The MH-M38 is a stereo audio receiver with loudspeaker outputs (and an inbuilt amplifier) that can play music from a smartphone/com...
Pycom GPy & FiPy Cellular LTE Firmware Update
There are three levels of firmware upgrades that are required on Pycom gear. First, performing an upgrade on the firmware of any of the Pycom microcontrollers is a simple affair. Download the Pycom Firmware Update application as linked in t...
Assemble a goBILDA Outlaw Chassis Kit - Plus Raspberry Pi and 8BitDo Control!
If you want a high-end robotics platform that is easy to expand with it does not get better than goBILDA! GoBILDA is a complete build system designed for makers, students, and educators. From curated kits, to many structural alum...
Arduino Workshop for Beginners
Welcome to the Arduino Workshop, where you'll be able to follow our guided course which covers everything you'll need to know in order to create your own Arduino projects and become a leveled up maker. My name is Sam and along with being ...
Loading and Unloading Filament for Ultimaker 3D Printers
Installing filament into your Ultimaker 3D printers will quickly become an intuitive process. But until that happens I'll be here to help run down the process and to teach you exactly how to do it whilst keeping your awesome 3D printer safe...
I SPI with Raspberry Pi
I SPI with my Raspberry Pi, something beginning with…S! Serial-Peripheral-Interface (SPI)! Welcome to our Raspberry Pi SPI communication tutorial. Today we’re going to look at how to use the SPI bus on our Raspberry Pi ...
Getting Started With Inertial Measurement Units | Exploring Degrees Of Freedom
In this guide, we'll be learning about sensors that measure inertial movement, how they work, how to choose the right sensor type, and how to get the most out of their readings. Hardware mentioned in this guide: PiicoDev Accelerometer ...
C Programming for Makers
Welcome to the C Programming Workshop for Makers! Here you'll be able to follow along with our series of easily digestible videos that cover everything you'll need to know to on your way with C programming and start making awesome projects....
Using Slicer for Fusion360 for Laser Cutting
Laser cutting is a very fast production and manufacturing method that has one limitation. You can only cut flat surfaces! Well don’t let that stop you from creating 3D objects and sculptures with a laser cutter, Fusion360 has a great ...
IoT with LoRaWAN, Pycom, The Things Network & Node-RED
Note: With the rollout of TTNv3, the "Setup" section of this guide no longer works - but we're keeping it here for posterity. Let us know on our forums if you need help getting started with the new method. In our two previous Pycom article...
Set Up a Geophone with a Raspberry Pi and an ADC (ADS1115)
Geophones are devices that generate electric signals proportional to the particle velocity in a sound/compression wave. More simply a Geophone is a super low frequency microphone for the ground. Geophones are used around the world to measu...
An Educators Perspective - Chibitronics
We have tailored guides on series circuits and basic switches, but that’s not even close to the limit of what you can learn and teach with Chibitronics. The Classroom Pack comes with all the components an educator would need to teach...
Raspberry Pi Workshop for Beginners
Welcome to the Raspberry Pi Workshop for Beginners! Here you'll be able to follow along with our series of bite-sized videos that cover everything you'll need to know to get started with your Raspberry Pi, and start making awesome project...
Choosing a Soldering Iron
Hello, and welcome to our tutorial where we’ll be looking at two different types of soldering irons and which one is going to be best for your workshop. We’ll be specifically looking at soldering irons, not how to solder, so for...
The Maker Revolution
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - the transition from a consumer buying goods to eventually having a major part in their creation. The Maker Revolution places strong emphasis...
Getting Started with Home Automation Using MQTT
What is MQTT? MQTT (Message Queue Telemetry Transport) is a simple and ‘lightweight’ way for internet-connected devices to send each other messages. This is important for home-automation because devices need to send messag...
Saleae Models Compared
Logic analysers are an incredibly valuable piece of test and measuring equipment, but sometimes it can be hard to work out exactly what you need, and what model is going to best suit your needs. If you’re not sure what a logic analyse...
OctoPrint Integration with Cura 2.6+ Lulzbot Edition
OctoPrint Integration is one of my favourite new features in Cura 2.6+: LulzBot Edition. In short, this integration means that you can print and control your 3D Printer via it's OctoPrint server. All from within your slicer window on your P...
Infinity Mirror Kit V1 - Assembly and tutorials
The Infinity Mirror Kit is a desk-top display that creates a dazzling optical illusion - a tunnel of light that tears through space! Note: This tutorial is for the Infinity Kit V1. We updated have updated to the Infinity Kit V2 as of ...
Prototyping a Circuit: Methods and Tools
Ah prototyping, the backbone of maker electronics, well really all electronics. Any successful device, product, or idea doesn’t just appear as a finished concept, it goes through stages of product and one of those is prototyping. In f...
How to Use Breadboards
Hello makers, if you love to prototype circuits and create electronic designs, then you’ll be familiar with the humble solderless breadboard. It’s where most electronic projects begin and is a familiar sight for tinkerers and in...
Circuit Scribe for Educators
Educators everywhere are lining up to have the most recent, high-tech teaching tools to introduce STEM learning in the classroom. With the rate that modern technology is advancing, educators can often feel overwhelmed with the sheer number ...
Setting up and Using the Adafruit 16-Channel Servo HAT for Raspberry Pi
This guide will teach you how to control up to 992 5V Servos through the GPIO pins on your Raspberry Pi! But more practically, without stacking multiple HATS (Hardware Attached on Top), this guide will teach exactly how to control sixt...
Getting Started With Relays | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Relay is, why we might use one, how to choose a Relay, and finally how to use one with a Raspberry Pi Pico. To follow along you'll need: A 5V SPDT Relay - I'll be using a 5V Single Channel Relay M...
8Bitdo NES30 Pro Controller Review
Today, we’re looking at the 8Bitdo NES30 Pro. It’s a newer controller from 8Bitdo and one that I’m really excited about. It’s an interesting gamepad, with the styling and form factor taking cues from both the classic...
How to Conserve Battery Life with IoT Projects
If you’ve ever created a project that uses batteries, you’ll be well aware how hard it can be to decide on elements in the project which can affect the battery life. You end up ‘umming’ and ‘ahhing’ for a...
Learning Arduino in Australia
Core Electronics is the official supplier for Arduino products Australia wide. We stock components from both Arduino.cc (Genuino) and Arduino.org (Arduino). Sourcing our products directly from Arduino ensures you are supporting the team beh...
Geting Started with CAD for 3D Printing
If you've picked yourself up a 3D printer, you've no doubt printed yourself a heap of models from Thingiverse by now. It's great fun and the best way to learn how to control the options you have available through Cura; scaling, rotating and...
PiicoDev Magnetometer QMC6310 - Guide for MicroBit
Let's get started with the PiicoDev® Magnetometer. In this guide, we'll connect the Magnetometer to our micro:bit, get it working as a compass, and read the magnetic field strength of a nearby magnet. To follow along, it's best to...
Getting Started with Rotary Encoders | Examples with Raspberry Pi Pico
In this guide, we'll learn what a Rotary Encoder is, when and why we might use a Rotary Encoder, and how to use a Rotary Encoder with a Raspberry Pi Pico. To follow along all you'll need is: A Rotary Encoder - we recommend using our br...
How to Pair and Map 8Bitdo SF30 Pro Controller with RetroPie
8Bitdo have brought joy to many retro-gaming enthusiasts with their SF30 Pro Bluetooth controller. It’s a fantastic piece of gear, and one of our favourite controllers to use with a RetroPie setup. We’ve covered off on our thoug...
PiicoDev Ecosystem Compatibility
PiicoDev is the open-source and best-documented platform specifically designed with rapid prototyping and maker education in mind. As fellow community educators, we have infused PiicoDev with ideas to ensure that every home project, school...
Our littleBits Gizmos and Gadgets Kit (2nd Edition) Review
The new Gizmos and Gadgets revision 2.0 from littleBits is here and we've decided to review the kit for any budding inventors (or inventor's parents) out there. The v1.0 kit was impressive enough, we were interested to see what littleBits c...
Our Arduino SPI Tutorial
SPI stands for Serial Peripheral Interface and it is a way to send data between microcontrollers and other small devices. It is a synchronous data bus, meaning it uses a clock to regulate the data transfer. SPI is also Full-Duplex com...
How To Setup Raspberry Pi Zero W Headless WiFi
So what does it mean to run headless?A computer setup without a monitor is said to be running headless. You might want to do this if you're installing your Pi into some project, or want to keep power-usage and cost minimal. This kind of se...
Our Rigol DP-832 Power Supply Review
The Rigol DP-832 is a 3-channel, benchtop power supply suitable for a serious maker, makerspace or product developer. In this video I'll take you on a tour of the supply's operation and give my two cents on things I like and dislike. ...
Makerverse Real Time Clock with Supercapacitor Backup - Raspberry Pi Pico Guide
Introduction This guide covers the basic use of the Makerverse Supercap Real Time clock on the Raspberry Pi Pico using our RV3028 MicroPython module. The MicroPython module implements some commonly used features of the RV3028 RTC but is no...
Makerverse Essentials Kit Guide | Build Circuits and Code with MicroPython
IntroductionWelcome to the guide for the Makerverse Essentials Kit. This kit provides the fundamental hardware required to construct many of the kits in the Makerverse Kits range along with providing hardware which will continue to be usef...
Remote Sensing with Particle Electron
Hey guys, how much fun are microcontrollers? They’re your own miniature slave to do your bidding in whatever way you choose, however as fun and all as using them to do math and crunching numbers, the real joy is seeing them interact w...
How to Choose a Bluetooth Module For Your Project
Alright, so we know that Bluetooth is awesome, and if you don’t, take a read of our Introduction to Bluetooth tutorial. But how exactly do we go about implementing Bluetooth communication in our projects? Well, fortunately for us, th...
Cura 2: Lulzbot Edition for Intermediate Users
After some serious touch time your LulzBot 3D Printer and the quick print options in Cura 2, it's more than likely that you want to make more specific changes to the way 3D Models are printed. Whether it be, changing the support type and st...
Support Material: Printing and Removal
By default, FFF/FDM 3D Printers require the 3D Models they print to grow up from the Print bed at an angle of 45 or more. This is by far the biggest limitation of all 3D Printers. To print models that don't follow that rule, and have parts ...
Raspberry Pi Pico W | Overview, Features and Specs
IntroductionLet’s take a look at the Raspberry Pi Pico W - a WiFi-enabled development board from Raspberry Pi. This overview article will explore the Pico W features and specifications. As always, there are additional resources at th...
PiicoDev Real Time Clock (RTC) RV-3028 - Getting Started Guide
This guide will help you get started with a PiicoDev Real Time Clock. We'll set and read the time/date, observe the power-backup capability, and configure the RTC with an alarm. A Real-Time Clock (RTC) is a timekeeping device that accurat...
3D Printing Better Print-in-Place Mechanisms
Print-in-Place mechanism is one of the special things about additive manufacturing that all other manufacturing methods just cannot replicate. They use various hinges, linkages and joints to create moving parts that are printed as a single ...
Infrared Sensing, Hardware Interrupts, and the Arduino
Infrared (IR) is a great way of using non-visible light to control electronics, and there are a bunch of modules that we can use with our Arduino. However, what do we mean when we are talking about infrared and electronics? Well, IR remotes...
Our Raspberry Pi Compute Module 3 Review
A new day is upon us, and it is glorious. After all, it’s not often that a new Raspberry Pi board is released. As you’re probably aware, the current iteration of the popular Raspberry Pi microcomputer is the Raspberry Pi 3. It h...
Our Overview of Makeblock mBot
Looking for the best way to get into robotics? Checkout Makeblock's mBot. This all in one robot is the perfect introduction to basic robotics, with its simple yet robust design, mBot is built with education in mind. The mBot kits modul...
Powerboost your LiPo Batteries
We're going to pick up where the LiPo Battery tutorial left off and look closer at the Adafruit Powerboost modules for charging your LiPos. We talked about the rules of using these batteries and how to make sure you don't set your project a...
Effective Ways To Detect People Using Common Sensors
In this guide, we'll look at common methods of detecting people and some of the different sensors you can use to detect people in your next project.Sensors covered in this guide: PIR Sensor RCWL-0516 Microwave Radar SEN0395 mmWave Rad...
Raspberry Pi Pico W vs. Pico | What's the difference?
IntroductionThis article will compare the Raspberry Pi Pico, and Pico W. Aside from the obvious difference (the Pico W has wireless connectivity), there are a few smaller and more subtle differences that are worth considering.Physical Comp...
Our recommendation on Breadboard Power Supplies
So, you’re looking for the right way to power your breadboard? You’ve found that your Arduino Uno just doesn’t quite have the juice to power up your circuit. It's likely that the microcontroller can output around 400mA whe...
Writing Code Onto MicroPython Boards
You have your shiny new MicroPython or Circuit Python board and you have Installed the Firmware and connected to REPL, but now you want to put your code onto the board. To do this we need to send the files over serial. Luckily Adafruit has ...
Wings of the Feather
The Feather boards are the brains of your project, we took a closer look at the different models in our Birds of Feather article, check that out first (especially if you have no idea what the difference is between a feather and a wing). You...
Ultimaker Cura - An Overview for Makers
This will be a guide giving an overview of Cura, the open-source 3D printing slicing application from the smart cats at Ultimaker. Put simply Ultimaker Cura is a software which allows you to turn the computer file of your design into a reci...
Swell Python Scripts with the Turtle Library
Time to flex some of the coding muscles we have gained. Using the knowledge we have with Python, this guide will go through the creation of interesting and dynamic graphic animations. The first codes in this tutorial are generators for geo...
Say Cheese with Raspberry Pi Camera
Ever thought it would be cool if your Raspberry Pi could see the world like you do? You’re in luck, camera support is an integral part of the Raspberry Pi hardware, it comes with a built in CSI connector for connecting camera ...
How to Debug MicroPython Code
When you are working on microcontrollers it can be very difficult to know what your code is doing, with MicroPython we can use REPL (Read Evaluate Print Loop) to see the debug output and run python commands in real time. This tutorial ...
Capacitive Touch Keyboard with MakeCode: Adafruit Circuit Playground Express
On the lower left-hand portion of every Adafruit Circuit Playground Express, there is a small onboard speaker and class D amplifier. This allows you to make some pretty loud sounds! The amplifier is also connected to the true analog output ...
I2C with Raspberry Pi
Hello there, how’s your day been? Good? Fantastic! Not so good? Don’t worry it’s about to get a lot better, because today we’re going to take a look at how to use the I2C interface on our Raspberry Pi to control I2C ...
How to Drive High Power LEDs – 3W Aluminum Backed Star LEDs
High power LEDs (Light Emitting Diodes) have different requirements that need to be met when compared to regular LEDs. Current regulation using only resistors is impractical so it is necessary to use a switched-mode voltage and current reg...
How to Build an Arduino Library
Have you ever wanted to simplify or automate a task using an Arduino? Yes? Well, have you ever wanted to simplify the code required for that task into a neat collection of easy-to-use functions? Also yes? Then this tutorial is for you! In t...
Arduino Projects with Sound (Using Sparkfun RedBoard)
Project Set 2 – Sound Welcome to the second Project Set from the Sparkfun Inventors Kit V4.0 Guide! In our last Project Set, we explored the basics of the Arduino IDE, some electrical and electronic concepts and looked at vario...
Micro:bit Soil Moisture Sensor
The Micro:bit is great for small portable projects like a soil moisture sensor. In this tutorial, we will walk through how to program a Micro:bit to make a reliable and consistent soil moisture sensor that will give consistent readings. The...
Moving From Arduino to Particle
In case you haven’t noticed, Internet of Things is the phrase on everyone’s lips right now; why make a device, when you can make an IoT device? And the good folks at Particle.io have made it easier than ever to create your own...
How to Use Ultrasonic Sensors
ECHO…echo…echo…echo… We’ve all had fun shouting into a cave or large space and hearing our voice coming back to us at some point during our childhood. And if you’re like me, a fully grown adult who...
PiicoDev Air Quality Sensor ENS160 | Getting Started Guide
The PiicoDev® Air Quality Sensor is based on an ENS160 multi-gas sensor that detects Volatile Organic Compounds (VOCs). These measurements are run through some algorithms to produce standardised outputs like Air Quality Index (AQI...
Controlling a Solenoid with an Arduino
In this tutorial, we will look at the basics of Solenoids and how they work. Then we will design a small circuit that can drive a Solenoid from the input/output pins on your Arduino board. We covered a whole bunch of rotational motion co...
What is Raspberry Pi?
Hi there! If you’re wondering what all the hype and interest surrounding Raspberry Pi is about, you’ve come to the right place. The original Raspberry Pi debuted in 2012, and is a credit card sized computer that has ports for U...
MicroPython for Micro:bit Workshop
Welcome to the MicroPython for micro:bit workshop! This workshop is aimed at makers who want to start programming with MicroPython, we will be using the micro:bit as it is very easy to use so we can cover the important concepts that will ap...
Capacitive Touch with Makey Makey
The Makey Makey introduces the concept of using everday objects like fruit, lead pencil drawings, play dough etc. to interact with your computer via USB. The Makey Makey acts like a HID device over USB, which means that it behaves just like...
Exciting Features - Ultimaker Cura
Ultimaker Cura is an excellent slicing software to get the best out of your 3D printers and make the greatest models it possibly can, but it can do so much more! Cura is a brilliant means to inspire and expand your own creativity particular...
Control Structures with Python
Welcome to the next step of comprehension for the fireball programming language of Python. This guide will provide you with tools to help aid conceptualisation of the control flow within your programming scripts. The control flow is th...
How to network XBee and the Arduino
Want to setup a wireless XBee network between some Arduinos and your PC? We're going to show you how. We will be using Series 1 XBee modules alongside some XBee Explorer USB modules from Sparkfun to set up our own Personal Area Network (PAN...
Relay Operation and the Arduino Uno
If you could operate your switch without physically toggling it on and off, you would open yourself up to an entire section of electronics. Relays are one of the best ways of doing this. A relay is essentially just a switch, controlled by a...
Zero To Maker Workshop | Fab Academy (Our Experience)
Welcome to 'Zero to Maker,' a workshop that will walk through and introduce a ton of tools and skills to help Makers of all skill levels! In this series, Jaryd and Liam will be completing projects as a part of the 2024 Fab Academy and...
Python and MicroPython - Compare and Access
Both Python and MicroPython are powerhouse programming languages. Each of them is capable of supporting your programming needs to almost the limits of your imagination. Both languages are transportable, open-source, growing in popularity, c...
Logic Level Converters for Particle
So you’ve got your Particle Photon or Electron, you’ve got your sensors and external components and you’re ready to build an IoT device to make the world your slave. But hang on a minute, the sensor you have only operate...
Object and Animal Recognition With Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto yo...
Pan-Tilt Hat with Raspberry Pi - Quick Start Guide
Pimironi Picade Pan-Tilt Hat lets you mount and control a pan-tilt module right on top of your Raspberry Pi palm-sized computer. Setting up a Pan and Tilt system has never been easier with absolutely no soldering required! Pe...
Let's take a look at Makey Makey!
Makey Makey is a compact circuit board which allows you to create circuits using anything you like and connect them up to a computer. You use alligator clips to connect things to the Makey Makey, and then your Makey Makey connectors to a co...
Arduino Boards, Compared
We're going to compare each of the Arduino Boards available to Maker's and Electronics Enthusiats. We'll discuss the features of each board, provide an informative pinout diagram with tonnes of detail, and toward the end of the article, pro...
Controlling Standard Servos with Raspberry Pi
This guide will teach you how to control any small and big servos with a Raspberry Pi 4 Model B (worth noting any Raspberry Pi Board with GPIO pins can be able to be used in this scenario. Servos are an immensely useful way to turn ele...
Pycom Pysense Getting Started Guide
The Pysense expansion board from Pycom has many sensors. In Pycom Pytrack Getting Started, I showed how with some Processing code we can see the real-time position of the board in 3D. That project works with the Pysense too. How about we sh...
Makerverse Audio Kit Guide | Play Music and Generate Tones
IntroductionWelcome to the guide for the Makerverse Audio Kit. This kit will allow you to build a music player, a musical keyboard, and a sound effect soundboard! To follow along you will need: The Makerverse Audio Kit The Makerverse ...
Fingerprint Scanner with Raspberry Pi Single Board Computer - Unlock with Biometrics!
Let's unlock Biometric Control on our Raspberry Pi Single Board Computers! Biometric Technology uses unique physical or behavioral attributes that are individual to each person and not (easily) replicable. Extraordinarily everyone on Earth...
Switches, Debouncing and the Arduino
When we boil it down, everyday interactions with electronics are usually limited to controlling stuff with switches. Whether it be turning on the lights, switching on your laptop or turning on the kettle, all examples of how a physical sw...
Create a Smartphone App for Particle Without Coding
By now you’re probably loving the platform that is Particle and all these crazy ideas of how to create the next big IoT thing (Internet of Things thing…hmm), but for many inventors, the stumbling block is integrating your creat...
All About Electrical Switches
On and Off. It’s the basis for all electronics, from the most sophisticated computer network to a simple circuit. Electronics is all about using one thing, to control another, input and output, on and off. Even the transistors inside ...
Getting Started with Particle Electron
In another tutorial we looked at the Photon board from Particle, and whilst Wi-Fi is awesome for many applications, it restricts you to a localised connection. Particle have once again come to rescue and provided us with a cellular solution...
Working with the Particle IDE
In case you haven’t heard, the Internet of Things (IoT) is upon us. More and more devices everyday are being connected to the internet to communicate to people and other devices. Particle have seen the DIY/maker community’s desi...
How to use Solar LiPO Chargers
Every day, Solar energy bombards Earth with about 173,000 terawatts of power. That's close to the yearly electricity bill for Planet Earth. Solar energy is free power from the stars. So the question stands, why aren't we using it more? Pric...
Analog Electronics Crash Course
Welcome to our beginners tutorial on analog electronics. Living in the digital age that we do, it’s easy to disregard the world of discrete analog components, however these concepts form the basis for everything from your mobile phon...
USB Keyboard-Mouse with Teensy
Hey all! By now you should have heard about all the wonderful Teensy Boards produced by Paul Stoffregen and the PJRC team but, in case you haven't, they're a collection of high-speed, ARM-based microcontrollers that...
Real Time Scanning and Storing QR Codes With Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS ...
Plant_io Basic Setup Guide | Automatically Water a Seedling Based on Soil Moisture
What We'll AchieveThis guide will help you set up a Plant_io controller to automatically irrigate a plant of your choice. This example focuses on germinating seeds, but this is only one option. Along the way we'll: Assemble a hardware pl...
Python Variables and Types
Continuing our Python journey deeper into this dynamo of a programming language we will take a leap into variables and types. Variables are one of the most fundamental concepts and exist in pretty much all programming languages. Variables a...
Three Golden Rules for Choosing a Power Supply (No Maths!)
Often the last consideration in a maker project, the DC power supply is the heartbeat of many electrical projects and the correct selection requires some consideration. Power supplies go by a lot of different names, you can call them Wall ...
RaspController - Use Your Phone to Control Your Raspberry Pi
There are many different ways to use your mobile phone to remotely control and manage any Raspberry Pi and one of the best options out there to date is the phone application RaspController (you can also find it for free in the Google P...
Controlling a Solenoid with Raspberry Pi and a Relay
Here is how to control a 12 Volt Solenoid with a Raspberry Pi using a 5 Volt Relay. Solenoids are an immensely useful way to turn electrical energy into a linear motion. Solenoids come in a variety of different specifications with 5 Volt an...
How to Use HC-05 Bluetooth Modules
So we’ve taken a look at what Bluetooth is in our Introduction to Bluetooth tutorial, and hopefully, you’ve found our Choosing a Bluetooth Module For Your Project tutorial useful in deciding which Bluetooth module is right ...
GlowBit™ rainbow Quickstart Guide for micro:bit
Let's do some creative projects to get familiar with the GlowBit™ rainbow and micro:bit. The animation runs for 10 seconds, and can be started by pressing either of the micro:bit's buttons In this guide we will: Wi...
Detect Speed with a Raspberry Pi, Camera and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto your Mi...
Waveshare 5.5 Inch AMOLED Screen for Raspberry Pi
Ever wanted a pocket computer with a Full HD screen (1080x1920)? Love tiny GPIO screens like this 3.5 Inch from Waveshare but want one that is a little bigger and higher resolution so that it is easier to read? Or want a really premi...
Getting Started with MQTT on Raspberry Pi Pico W - Connect to the Internet of Things!
IntroductionIn this guide, we'll get a Raspberry Pi Pico W to send and receive data to the cloud using the MQTT protocol. To follow along, all you'll need is: A Raspberry Pi Pico W Understand how to connect the Pico W to WiFi Underst...
Temperature Sensing With Raspberry Pi
Is it hot in here, or is it just my Raspberry Pi? A Raspberry Pi sitting on a desk doing nothing is kind of boring. However, a Raspberry Pi that can measure the temperature and make decisions based off that information is awesome! The Rasp...
Makerverse Nano Power Timer
Introduction The Makerverse Nano Power Timer is an ultra-low current consumption power controller designed to periodically turn on a battery powered microcontroller. It is perfect for maximising the battery life of data-logging sensor...
Capacitive Touch Keyboard with CircuitPython: Adafruit Circuit Playground Express
On the lower left-hand portion of every Adafruit Circuit Playground Express, there is a small onboard speaker and class D amplifier. This allows you to make some pretty loud sounds! The amplifier is also connected to the true analog output ...
How to Build a RetroPie Console
Perhaps you’ve read our Gaming Kit for RetroPie tutorial on how to setup a RetroPie console and wondered what’s required to actually build one, or heard about it and not been sure what you need. Well, today is your lucky day bec...
Using your Arbitrary Waveform Generator
By now you are aware that when it comes to measuring electronic signals, oscilloscopes are what you are going to be using. However, if you were providing a circuit with a particular signal, a function generator is the perfect tool for tha...
Internet of Things with Pycom and Adafruit IO - From Zero to Hero
Introduction We’re going from zero to hero. Starting from nothing we’ll get a WiPy communicating with Adafruit IO, an IoT service out on the Internet. We’ll be able to send data from the device to the cloud and control th...
How to use GPS with Arduino - Parse and Log NMEA Sentences
Now that we've investigated and explained how How GPS Receivers work we can apply that understanding to some real-world applications of of the ideas. To start, we can use any GPS receiver, an Arduino Uno and some male-to-female Jumper ...
Infrared (IR) Controlled Lights with CircuitPython: Adafruit Circuit Playground Express
The latest Circuit Playground board, the Adafruit Circuit Playground Express comes equipped with an onboard IR transmitter and receiver! This can be used to communicate with TVs and other household devices. You can also use infrared remote ...
Installing Python Packages
So, you want Python to do something very functional but do not feel like writing heaps of code to achieve that functionality? Then look no further, this guide will teach you exactly how to do that by utilising Python Packages. Python P...
How to Use a Logic Level Shifter/Converter
So you’ve got your microcontroller/development board ready to go, you’ve got your sensors and external components and you’re ready to build an IoT device to make the world your slave. But hang on a minute, the sensor you h...
Cameras Compared for Raspberry Pi
There are so many types of cameras modules and lenses that are plug-and-play for Raspberry Pi Single Board Computers and that number is steadily increasing. From day to night, you can keep track, photograph, and record your surrou...
Pycom Expansion Board - Getting Started
Where do I start? If you’re new to programming Python is a great place to start! I’ve seen Python taught to primary school age children and I have used Python in a Machine Intelligence course at university. It’s no wonder...
How to use Force Sensitive Resistors with a Raspberry Pi and a ADS1015 ADC
Force-sensitive resistors (FSR) are remarkable electrical components and are proper unsung heroes in the Makers World. Name me a better variable touch input device which has basically no moving parts, all whilst being available in such a t...
What Are NeoPixel LEDs?
So in case you haven’t heard yet, digital LEDs are the go-to solution for any project that uses RGB LEDs and you want to avoid the rat's nest that ensures when using multiple RGB LEDs, each colour requiring its own connectio...
Our littleBits Rule Your Room Kit Review
"Yes, I would recommend this a friend." That's the verdict of 90% of people who pick up the Rule your Room Kit from littleBits. We love it so much, we're most definitely recommending it to you and your family. But you don't need to take ...
DIY Solder Stencils with a Laser-Cutter
When it comes to assembling a prototype Printed Circuit Board (PCB), there are a couple of options for applying solder-paste: Paste each individual pad by hand with a syringe, or; Use a stencil to paste all pads in one pass. The firs...
Pycom Pytrack Getting Started
In this getting started guide we’ll use the Pytrack from Pycom to detect our location on Earth using the onboard GPS module and use the accelerometer to control a 3D model on the PC. I put a WiPy onto my Pytrack, connected it to ...
All About EL Products
Electroluminescent wire, often referred to as EL wire, is a thin copper wire coated in phosphor which will produce light when alternating current is applied to it. The light emits a similar feel as if it were a neon light or ...
Pycom GPy Getting Started
warning: Pycom has updated their libraries and the code listed below may not work. If you discover this and find a fix, please post it on our forum and we'll send you a $25 store credit along with a huge thank you. Go to Forum Thread. ...
PiicoDev Button | Getting Started Guide
Buttons are a ubiquitous user interface - of course, you've seen them everywhere! The humble button is often the fastest way to create a control interface for your project too. This guide will help you get started with a PiicoDev® Butt...
Pimoroni Blinkt: Setup and first script
Not quite sure how to get started with your Pimoroni Blinkt module? Let's set one up and have a play around! We'll guide you through the installation, open up some examples and try our hand at writing a simple program. You'll need: A Ra...
Raspberry Pi High Quality Camera – First Pictures and Videos
[Note - Terminal Commands talked about here have been superseded with the new 'Bullseye' Raspberry Pi OS. Link here for new 'Bullseye' camera commands. If you want to use the commands found on this page download and flash the old 'Bu...
Arduino vs. Raspberry Pi
One of the big questions in DIY electronics circles is which DIY platform is going to be the best for me? And the two biggest platforms right now is Arduino and Raspberry Pi. Whilst at first glance they might seem the same; circuit board ...
How to Rotate Raspberry Pi Video Display / Screen
Like many things in the Raspberry Pi ecosystem, functions such as rotating the display output can be a little unintuitive at first. Or perhaps you’re not sure how to get rid of that annoying black outline on your screen. So, we’...
Serial Monitoring with Tera Term
Monitoring what’s happening inside your microcontroller is an invaluable tool for prototyping and debugging. One of the best ways to do this is to send/receive data over a serial port. Most microcontrollers have a serial port that can...
Makey Makey in the Classroom
Hey guys, if you’re looking to get the creativity and fun of Makey Makey into classrooms or workshops, then you’re in the right place! Makey Makey is an incredible tool for educators to get kids thinking about how they can use t...
Infrared (IR) Controlled Lights with MakeCode: Adafruit Circuit Playground Express
The latest Circuit Playground board, the Adafruit Circuit Playground Express comes equipped with an onboard IR transmitter and receiver! This can be used to communicate with TVs and other household devices. You can also use infrared remote ...
Power Supplies for your Project
Ever had the issue where you have dozens of old phone chargers and appliance plug packs piled up in a rats nest of AC-to-DC mayhem? We tend to breeze right past these square, black power supplies, not knowing what's happening under the hood...
Logic Level Converters for Raspberry Pi
So you’ve got your Raspberry Pi, you’ve got your sensors and external components and you’re ready to build a world-conquering robot beyond compare. But hang on a minute, the sensor you have only operates on 5V and you vagu...
Flash MicroPython Onto An ESP32
The ESP32 family of microcontrollers are incredibly powerful (2 Cores on a Microcontroller!) and when combined with the awesome writability of MicroPython can be used for all kinds of projects. The ESP32 generally does not come with MicroP...
Arduino, Learn the Lingo
Getting into the Arduino environment is a lot of fun but with so many acronyms and slang terms its easy to get confused. Knowing this first hand, I have put together a glossary of sorts for terms relating to Arduino, if you are new to the A...
Character Displays with Particle
Crunching numbers is fine, but sometimes you really need to visualise what’s going on in the tiny brain of your Photon. There are numerous different ways to visualise data or text on a microcontroller from binary LEDs, to HDMI display...
Pycom Expansion Board 2.0 Overview
It would be good to have some understanding of Pycom microcontroller boards before reading this article. We won’t go into what capabilities each microcontroller board has. If you’d like an introduction, try our Pycom WiPy Overvi...
Getting set up with Node-RED on the Raspberry Pi
What is Node-RED? Node-RED is a tool originally created by IBM for flow-based programming, and has built-in support for the Raspberry Pi and it's GPIO capabilities. It runs on top of Node.js, and can be accessed with just a web browse...
Our Overview of Makeblock's Ultimate Kit 2.0
The aptly named Ultimate Kit 2.0 is the final kit in the line-up of educational robots from Makeblock. With over 160 independent mechanical parts and modules, the Ultimate Kit 2.0 answers the call for almost limitless creative freedom. Matc...
Pycom Bluetooth
Bluetooth is a low-power radio technology used to link devices wirelessly. Most commonly recognised as the way to link a mobile phone to a car or speaker, it has many uses beyond that. The "low power" aspect is not a shortcoming, as a large...
4G and GPS HAT For Raspberry Pi - Waveshare SIM7600X
Love your Raspberry Pi but wish it had even more connectivity akin to your mobile phone. Then the Waveshare 4G HAT is the solution for you! HAT simply means Hardware attached On Top. With this installed on your Raspberry Pi Single Board Co...
Wi-Fly with Feather Boards
I’ll level with you; the idea of microcontrollers and wireless networks was a little daunting to me initially. How on earth was I going to connect and control it with Wi-Fi?! But when I eventually I waded into the world of networking ...
Arduino Projects with Light (Using Sparkfun RedBoard)
Now that your RedBoard is set up on its baseplate and the Arduino IDE is installed on your computer, we can begin our first Arduino-based Project Set! The First Project Set explores light and the type of electrical component we will be usin...
Upgrade your Project for the Raspberry Pi 4
The New Version of the Raspberry Pi 4 has started going out to makers everywhere. If you are wanting to upgrade your old RPi3 project to take advantage of all the cool new features there are a few steps we are going to have to take first to...
Lightning Sensor with a Raspberry Pi Single Board Computer - 40 KM RADIUS RANGE!
What if I told you that you could have the power to detect a lightning strike from 40km away? You'd probably think I've gone mad watching too many Marvel movies. But it is true! All thanks to the DFRobot Gravity: Lightning Sensor. Accessib...
How to get started with Circuit Playground
Have you heard about the Circuit Playground? It's the new all-in-one electronics platform from Adafruit. It was created to bring all the fun features of electronics and physical computing to makers, but It's dead-simple to use, solde...
How to Setup ATOM (Code / Text Editor) on Onion Omega2
In this tutorial, we will learn how to code for the Onion Omega2 on our PC, and then wirelessly upload our code using the ATOM text editor. The ATOM text editor is a powerful and easy to use text editor developed by the team at Github...
PiicoDev Atmospheric Sensor BME280 - Micro:bit Guide
Introduction This guide will help you read weather data (Temperature, Air Pressure and Humidity) from your PiicoDev Atmospheric Sensor and a Micro:bit. To follow along, it's best to have: A Micro:bit v2 (v1 does not...
Raspberry Pi Pico W | Connecting to the Internet
IntroductionIn this guide, we'll get a Raspberry Pi Pico W connected to the internet using WiFi. To demonstrate the connection we can query a webpage, or get the current time from a time service. To follow along, all you'll need is: A R...
Pycom FiPy Getting Started
Say you want to build a sun-tracking solar panel. You could add a tiny computer, like an Arduino, to control it. That might be all you need. But what if you need to connect to it to control it from somewhere else? Connecting it into your ho...
GlowBit Matrix 4x4 - Python and MicroPython Guide
Introduction This guide will cover the basic functionality of the GlowBit Python library when driving a GlowBit Matrix 4x4 module. To follow along, it's best to have: A GlowBit Matrix 4x4 A Raspberry Pi Pico ...
Gaming Kit for RetroPie
Video gaming has evolved tremendously over the last decade, console games produce near real-life graphics, and playing with friends across the globe is easier than sending a text message. This is all well and good, but there are those of us...
Powering Portable Projects: Batteries
Want to make your project portable? We've put together a quick guide to get you up to speed on battery options and help you decide which batteries might be best for your project. Batteries are a whole different game to plug packs and bencht...
How to Run a Python Script Automatically on Bootup / Startup with Onion Omega 2
A common issue many makers face when they move from microcontrollers to Single-Board-Computers is how to get them to run a program automatically when they are powered on. People who have cut their teeth on Arduino, Micro:bit, and other micr...
LCD Screens and the Arduino Uno
Display devices are used to visually display the information we are working with. LCD (Liquid Crystal Display) screens are one of many display devices that makers use. We have libraries to control specific LCD functions which make it ridicu...
Data Logging with the Micro:bit and OpenLog
The Micro:bit by BBC is a great data collection tool, it just needs a little help remembering what it has measured! This tutorial is made for those Micro:bit projects where transmitting your sensor data over radio or Bluetooth to a computer...
Circuit Playground Express TV Remote
Have you ever lost or broken a TV remote before it's time? Have you ever wanted to spice up the way you change channels or inputs on your TV? Have you got a greedy housemate who always steals the remote off you? If any of these are the case...
PiicoDev Atmospheric Sensor BME280 - Raspberry Pi Guide
Introduction This guide will help you read weather data from your PiicoDev® Atmospheric Sensor and a Raspberry Pi single-board computer To follow along, it's best to have: A Raspberry Pi (model 3, 4, Zero ...
PiicoDev Atmospheric Sensor BME280 - Raspberry Pi Pico Guide
Introduction This guide will help you read atmospheric data from your PiicoDev® Atmospheric Sensor and a Raspberry Pi Pico To follow along, it's best to have: A Raspberry Pi Pico with pins soldered (pointing do...
How 3D Printing Works
3D Printing is one of the ways we can turn virtual 3-dimensional models into real world objects. It is an Additive manufacturing (AM) process, building models layer by layer. AM is the opposite of subtractive manufacturing which takes a blo...
What is a Kano Computer?
How many young people are able to assemble a computer, from scratch? Sure, adults can do it. There are even IT professionals and avid PC enthusiasts that take it to the next level; customizing everything down to the color of the Power LED a...
Pi To All The World With GPIO
So you’ve got your Raspberry Pi. You’ve gotten NOOBS setup on it, explored Raspbian a bit, and you’re feeling like a bit of a pro. Awesome! Now let’s get down to the nitty gritty side of things, what it’s ...
Fire-EdUp | Add our Own Code
It's time to make our own changes to the Fire-EdUp Platform's code! In this guide we'll modify the behaviour of the platform to create an audible alert under certain conditions. Follow along with the video below, and see the references be...
Color Matching with the Light Sensor and CircuitPython: Adafruit Circuit Playground Express
The Adafruit Circuit Playground Express comes equipped with an analog light sensor, but it can be used for much more than just sensing light or darkness! The light sensor has a similar spectral response to the human eye. Its connected to an...
How to Flash/Write Raspbian OS onto Raspberry Pi Compute Module 4 (CM4)
While the Raspberry Pi Compute Module 4s (CM4s) share a lot with the regular Pi 4 Model B, getting started with the flashing process can be quite different depending on which model you pick! This article aims to demystify that, so without f...
Understanding ESP32 Naming Conventions
Espressif is a constantly ground-breaking company that produces lots of really cool development modules which includes the ESP32. ESP32 Boards, ESP32 Dev-Kits, and ESP32 Modules (the part that gets soldered to the Board/PCB) are all about ...
Remote 3D Printing with OctoPi
Remote control of your 3D printer is a particularly appealing concept, especially if you've been forced into printing via USB in the past. Using your new 3D printer should be as simple as plugging it in, uploading some G-Code and pressing '...
Perfectly 3D Print All Types of Lithophanes and Add Colour
Of the many great objects you can create using any 3D printer lithophanes are definitely up there. Traditionally lithophanes were an etched or moulded artwork created on a very thin translucent porcelain that can been seen clearly only...
Which Raspberry Pi Case is Best For You?
What’s even better than the world’s most popular microcomputer sitting on your desk? When it’s sitting there in a case which protects it, makes it easier to use, and gives your desk some style. If you buy a Raspberry Pi i...
Makerverse Real Time Clock with Supercapacitor Backup - Raspberry Pi Guide
Introduction This guide covers the configuration steps required to use the Makerverse Supercap Real Time Clock module as a backup RTC on a Raspberry Pi. This is required for remote applications when Internet access is impractical and accur...
GUI with Tkinter in Python
Welcome to the next step on this Python voyage. Today we will be creating graphical user interfaces using the powerful Tkinter library. Graphical user interfaces are referred to as GUI and can be pronounced as Gooey. GUI is a visual way of ...
Our Adafruit Circuit Playground Express Overview
Adafruit has done it again with the new and improved Circuit Playground Express. This new version of the Circuit Playground is packed with even more sensors, and capacitive touch ready connection pads. This is a great board for makers ...
Visual Thermometer with CircuitPython: Adafruit Circuit Playground Express
The Adafruit Circuit Playground Express comes packed with sensors, and for this tutorial, we are going to learn to use the onboard thermometer (technically a thermistor)! We will take temperature readings with the thermometer and print out ...
Ultimaker 2+ 3D Printer and Ultimaker 2 Extended+ 3D Printer - Overview, Setup and First Print
This will be an overview, initial setup and first print guide for the Ultimaker 2 and Ultimaker 2 Extended . Quick links for the contents of this guide is seen below. Printer Overview Printer Characteristics ...
Identify Electrical Connectors
There are a ton of electrical wire connectors, too many to elaborate on in a single guide, however there are a couple of connectors that as a maker you will come across. Often when starting your way into the electronics world all you need ...
Solar Powered Raspberry Pi 4 Model B
This is going to be easier than you thought (or at least much easier than I thought)! Today we will create a Raspberry Pi 4 Model B UPS PiJuice System that will be completely powered by a Solar Panel. It's coming up to winter over here so I...
3D Printable VESA Mount for Argon One Case And M.2 Case
[Update 18-02-2021 - Made a Vesa Mount for the Argon One M.2 Case as well so nobody missed out] A quicky article for those who have their Raspberry Pi 4 Model B all tucked in snug by the very stylish Argon One Case but wish they could...
Laser Cut High Rise Case for the Arduino Uno
If you put a shield on top of an Arduino Uno there aren’t very many options available to protect it all inside a case. You can always make one yourself though, so that’s exactly what we did! This “High Rise” case for...
What is the better tech, innoBits or littleBits?
We get a lot of interest from parents and educators surrounding littleBits and innobits. Especially the difference between the two products. Both are magnetically connected electronic building blocks. Both products empower people to invent ...
GlowBit Stick 1x8 - Python and MicroPython Guide
Introduction This guide will cover the basic functionality of the GlowBit Python library when driving a GlowBit Stick 1x8 module. To follow along, it's best to have: A GlowBit Stick 1x8 A Raspberry Pi Pico or...
MOVE Mini Assembly Guide
The :MOVE MINI allows you to turn your micro:bit into a simple robot! In this guide, we will give you some tips and tricks for assembling the :MOVE mini. This is a DIY assembly item and takes 30-60 minutes to fully assemble. There is a grea...
Cool API Python Scripts
Let us set our codes free into the world wide web and design codes which access real world data! This real-world data will represent the current reality of the world around us. Application Programming Interface requests is the method that a...
Boards of a Feather
Have you ever used an Arduino board, and wanted to hook it straight up to a JST connected LiPo battery but knew it wouldn’t work? Or maybe you wanted a microcontroller with built-in wireless capabilities? Well, Adafruit has developed...
Pose Estimation and Face Landmark Tracking with Raspberry Pi and OpenCV
[Update – Until there is correct compatibility of OPEN-CV with the new Raspberry Pi ‘Bullseye’ OS I highly recommend at this stage flashing and using the previous Raspberry Pi ‘Buster’ OS onto yo...
GlowBit Matrix 8x8 - Python and MicroPython Guide
Introduction This guide will cover the basic functionality of the GlowBit Python library when driving a GlowBit Matrix 8x8 module. To follow along, it's best to have: A GlowBit Matrix 8x8 A Raspberry Pi Pico ...
Workaround for the RetroPie Bluetooth Security Bug
The Problem: You may find that while setting up RetroPie on your Raspberry Pi that pairing new Bluetooth controllers results in something like: During the "Please choose the security mode - Try the first one, then second if that fails",...
Raspberry Pi Pico with LoRaWAN and The Things Network - Makerverse LoRa-E5 Module - Transmit Weather Data into IoT
Feel restricted by your connectivity? Want to send data from a remote node 10km away from civilization? Or ~3km when you are in a built-up civilization. Feel the urge for Liberation? Then I have the solution for you! Using only hardware bu...
PiicoDev Ultrasonic Rangefinder | Getting Started Guide
Similar to how bats echo-locate and how submarines use sonar, the PiicoDev® Ultrasonic Rangefinder uses sound waves to measure the distance to an object. It sends out a high-pitched sound wave, which bounces off of the object and comes...
All About LEDs
Hello and welcome to our tutorial where we a look at all things LED. Now first of all, what is an LED? LED stands for Light Emitting Diode and is an electronic component used to convert electrical energy to light energy. This process is cal...
LittleBits Community & the Workshop Set
LittleBits have launched a global network of organizations to share and spread the word of littleBits. It's all to put the power of electronics in the hands of everyone. The 'chapters' are simply locations such as maker spaces and libraries...
How to make a Raspberry Pi NAS - A NAS-Berry that Runs Open Media Vault
Welcome to the best article on setting up an OpenMediaVault-based NAS on a Raspberry Pi Single Board Computer! This guide is the fastest and best way to go about it. Raspberry Pi single-board computers are purpose-built to run 24/7, with a...
FAQ on Lulzbot Support and Warranty
What level of support do I get with my Lulzbot products? For all technical support enquiries for anything Lulzbot related, Aleph Objects have support covered all-day long. Email [email protected] and the team over at AO will get back to ...
Using Teensy with Arduino IDE
If you’ve come looking for how to get your Teensy board up and running using the Arduino IDE, then you’ve come to the right place. Whilst you can use the standard Teensy loader application to flash compiled code directly to yo...
Writing SD Cards for your Raspberry Pi
To get your Raspberry Pi working, you'll need an SD card with a working operating system written to it. While NOOBs (New Out of Box Software) is a great headstart into the world of Raspberry Pi operating systems. It comes preloaded with Ra...
USB MIDI With Teensy
If you’re a musician or have had anything to do with the entertainment industry, you may have heard of the term MIDI before. MIDI stands for Musical Instrument Digital Interface and was created in the mid-80’s as a way to standa...
Our Recommendation for your first Benchtop Oscilloscope
You’ve been working on that project for days, even weeks, and you’ve gone through all the steps of the process; meticulously ensuring everything is above board. And yet, for some unexplainable reason, your circuit is acting out....
Micro:bit Temperature and Humidity Sensing
The Micro:bit has the ability to measure temperature by sensing the temperature of the silicon die inside the main CPU. This works because the Micro:bit runs cold, and the temperature of the CPU is usually a good approximation of ...
Using Copper Tape with Paper Circuits
What is a Paper Circuit? STEM technology has evolved into all kinds of fantastic forms with many brands bringing craft and electronics together in new and innovative ways. There’s plenty of products which make use of ‘paper cir...
Printing Perfect First Layers - Ultimaker Cura
If your utilizing a correctly set up Ultimaker S5 3D Printer you should have no issues with first layer printing. So long as there are print profiles available on Cura, which most likely it will, with a correctly set up 3D printer you will ...
Introducing CircuitPython: Adafruit Circuit Playground Express
CircuitPython is a variant of MicroPython that is designed with ease of use and simplicity in mind, and it works great with the Adafruit Circuit Playground Express. CircuitPython is based on the very popular Python programming language, the...
Our Review of the MOARstruder by Lulzbot
Toolheads for your 3D printer come in all shapes and sizes. The different models available from Lulzbot are all designed with a specific purpose in mind, usually to add a filament type to your 3D printing repertoire. Dual extruders enable y...
Integrated Computer Vision Package - OAK-D Lite With Raspberry Pi Set Up
If you ever needed a performance boost when running Machine Learnt AI Systems (like facial recognition) with a Raspberry Pi Single Board Computer then I have a solution for you. The OAK-D Lite. The Oak-D Lite is the Leatherman Multi-tool o...
Create Fantastic Finishes on 3D Printed Components
A special part of me enjoys it when people go ‘I cannot believe that was 3D printed’ and one of the best ways to get that reaction is through post-processing. Now not to belittle the beauty of a raw print result you can achieve ...
Plant_io Sensors Guide | Connect Sensors and Log Data
In the Plant_io Basic Setup Guide we assembled the Plant_io platform to automatically irrigate plants, and sprouted some seeds. As the project runs, a log file is updated with data captured at each interval. This simple log allows us ...
Chibitronics at Home - STEM Starter Kit
Now that we have dipped our toes into the Chibitronics environment, let's take a look at a more in-depth kit and see what kind of projects it offers. The Chibitronics STEM starter kit comes with: 1 Circuit Stic...
UNITRAC
The UNITRAC (UNIversal TRACtion system) is a simple 3D printable conversion for the Black Gladiator-Tracked chassis, It’s designed to transform the large wheelbase platform into a self-contained propulsion system that has all the torq...
GraviTrack Enhancements - Lights and Sound
Introduction Searching for solar panels and related items on the Core Electronics website; I came across the Solarbotics GraviTrack Marble Machine Kit. I thought the kit would be a good educational tool for the grandkids. The kit was a hit...
Roverling
Introduction
My first 3D printer was a CTC generation 2 clone of MakerBot ‘The Replicator Dual’, circa 2012. It died a little while back and has since been replaced ...
Robot Arm Upgrade Project
This project has been a long and tricky one for me, I purchased my robot arm kit from Jaycar many years ago with the intention of controlling it from the start. I used to work with industrial robots, so when I saw this robot kit for sale I...
IoT Pet Feeder
The objective of this project was to create an Internet of Things (IoT) device that could give pet access to a food bowl when a text message command was sent from a remote location. I had never done an IoT project before, so I wanted to ke...
Roverling Mk.ⅠⅠ
Introduction
A few months back I created a basic mobile platform using parts from an old 3D printer. It was fun but not very practical. I designed Roverling Mark II so I could experi...
Articulated Mule
Converting a Mule into an articulated 4 wheel vehicle. A 'Mule' is/was a hand trolley with a motorised elevatable platform. What for? Just for fun, want to be able to control it using the R2D2 droid inventor app via LittleBits boards, why ...
Quadbeest - A Flying Strandbeest
Introducing to you today, the Quadbeest, the next evolutionary step in the Strandbeest genealogy. It seemed to be about time for Strandbeests to evolve to take over the air, so I made it happen. Able to be controlled over a kilometre in the...
Bill of Materials
Auto Tracking Camera System
The purpose of this project is to design a system that will automatically track stars or satellites. The first version, described here, is specifically to track stars and operate a Raspberry Pi HQ camera to take a series of long-exposure im...
Ping Pong Launcher
I like to take on projects that give me an opportunity to learn new things. For this project, my two goals were to learn more about face detection algorithms and PID controllers but of course, there were so many more skills learned along th...
WiFi Garage Door Controller with Raspberry Pi Pico W
I strapped a Raspberry Pi Pico W to my garage door motor and now I can control my garage door from my phone! The Pico W hosts a simple webpage on my local network with three control buttons - one for Up, Stop and Down. Pressing one of...
Epoch Clock
I read somewhere about UNIX Epoch time and thought wouldn't it be neat to have a clock that showed time in this format? This project developed from that idea. I had a unused GPS module with serial output so I thought it would also be cool ...
Mini Desk Vacuum
Chances are if you are anything like me, being a maker is often an excuse to create as big of a mess as possible during the duration of a project. And after the project is finished? You are left with an enormous mess to clean up, taking awa...
Micro:bit based GlowBit Car
I made this car because at school there was a Lego We-Do tug-of-war competition but the cars only drove backward and I wanted to make a car that can turn and drive forwards. If you make this car don't throw away the chassis box because I ...
IoT House
These days we can do just about anything on our phone, we can control so many aspects of our lives using the technology in our pocket, but the most mundane aspects of our lives; opening the garage door, blindly reaching for the light switch...
WhyzaGC - Feather ESP32 addon to the MightyOhm Gieger Counter
This project is about adding a wireless Adafruit Feather HUZZAH ESP8266 or ESP32 v2 with Adafruit Featherwing 128x64 OLED to interface with the self-assembled MightyOhm Geiger Kit.
Introduction
I am always on ...Introduction
I am always on ...
Hands-free Selfie Camera Control
Ever wanted to record a video and be included in it? My children did. One does parkour, and the other loves to dance, both want to perfect their art by watching their moves during practice. They asked their inventor/tinkerer dad, "can you ...
IoT Chicken Shed (Arduino, Wifi)
If you have chickens and find you're not always available to close the gate at night or check the water levels each day, then why not use an ESP8266 to automate your chicken door and receive alerts door status and low water level, as well a...
SOLARBOI
Since I was young, I've always loved to explore. Over the years, I've tinkered with RC cars and played with planes, which were always plenty of fun. But I always dreamed of going out further - out into the real world, far beyond the confine...
Pico Baro V2
Introduction:
The inspiration for this project stems back to my childhood when I was curious to find out how the mechanical barometer worked.
Introduction:
The inspiration for this project stems back to my childhood when I was curious to find out how the mechanical barometer worked.
Arduino Tide Gauge
I used an Arduino and a US-100 ultrasonic sensor to make an extremely low-cost tide gauge. This project measures the tide by sensing the distance to water using a US-100 ultrasonic sensor. The device has a 3D printed base&nb...
Racing Simulator Motion Platform
Hi. My son and I have made our first Racing Simulator Motion Platform. It has been a challenge but we now have a playable situtationIt has been a long journey, starting off with info from the great people at www.xsimulator.net and a lot of ...
DIY Pi Buggy
The motivation behind this project came from a robotics and engineering club that I've been going to. I've been saving my money and building up an understanding of raspberry pi and electronics. The reason I chose this project was to get use...
The Euclidean
I'm an amateur musician but a pretty serious classical & jazz pianist, and this project arose out of my interest in exploring the difference between writing music for synthesisers and music for piano. I work as a mathematician, so...
The Amazon Alexa-Enabled Smart Pool System
This project is to allow remote control of my pool and associated lights with a dedicated display inthe house, a phone application and Amazon Alexa. Any and/or all of these input devices may be usedto control the pool. The pool temperature ...
safePower
I like working with the Pi Zero W and Pi 4 as they are very compact, very powerful and very cheap for the capability they offer. I want to use them on small projects, stand-alone, and can't always guarantee power. As we know most Pi's don't...
PowerPlay SSR Control
Introduction
The aim of PowerPlay is to provide an Arduino platform for managing downstream Solid State Relays (SSR) simply and safely. PowerPlay consists of a custom Arduino Shield, ...
Hydra Bluetooth Speaker
Wow - this is one monstrous sounding and great looking speaker - even if I do say so myself! This is basically a 2.1 (stereo + subwoofer) system made with 3D plastic parts. Both the full range and subwoofer speakers are based on closed (se...
Solar Charging Station
The aim of this project was to use the sun to charge some batteries with 1W and 2W Seeed solar panels. The DFRobot Solar LiPo Charger and a Sunflower Solar Power Manager were purchased. Initially, this was unsuccessful because I did no...
grinder_timer
Making a dumb coffee grinder slightly less dumb. This is a programmable timer tethered to a Rancilio Rocky coffee grinder. The Rocky is a "dumb" grinder and electrically very simple. Basically it's an ac motor with an on/off switch and a m...
LoRa P2P Wireless Gate Alarm
Introduction
My front gate is a long way from the house at around 300m. I don’t want people wandering around my property without knowing about it. This project uses two Raspberry Pi P...
Creating our own Raspberry Pi 3 Case
We've got a whole bunch of Raspberry Pi 3 Cases here at Core Electronics. From the Official Enclosure that's perfect for most uses, right through to the gilded PiBow Coupe from Pimoroni. All of the cases we see have one or two impressive fe...
mintyPi
This is an awesome project that takes about 6 hours to complete. Hours upon hours of endless fun thereafter! Ideally, some prior soldering experience is advantageous but if you take your time and practice before you start it's beginner fri...
Coffee Grinder With Arduino
Using a few bits and pieces, this ordinary coffee grinder now has two presets to run the motor for a programmable length of time. The idea being that the grinder running for a set amount of time will deliver a certain amount of coffee each ...
Camera Dew Controller
Introduction My passion hobby is night-time time-lapse photography and astrophotography/nightscapes. This means a lot of time spent outside in the dead of winter overnight and an issue that I faced was dew condensing on the lens. This is...
Backyard Birdcam
Introduction
I had been thinking about how best to capture clear close-up photographs of some of the many birds we see around our property for quite a while and mulling over a variet...
Autozem
Introduction So now everything is available in this day and age, and all those childhood dreams can now come true as parts, technology and software has come a long way. I had recently taken up the hobby, RC planes. Eventually I learnt ho...
IOT Shed
The driver behind this project is to allow the remote control of some of the equipment in my shed. I have a CNC router/laser cutter that uses my compressor and dust extractor whilst it is running, and well whats the point in having a comput...
Hyperweb: Interactive Art for Vivid Sydney
Hyperweb is a collaborative interactive sculpture installation at Vivid in Sydney. I designed and built a crowd sensing weather station that is used to control an audio "soundscape" within the piece. It also triggers light show events that ...
IoT Soundscape
I had been captivated by the sound levels of trains I could hear passing by Metford throughout the day/night. I wondered if a sound level sensor reporting data back over LoRa would help me understand when a train was noisy. I also like the ...
ATX Benchtop Power Supply
Despite having two high-quality variable (but analog) benchtop power supplies, I decided you can never have too many. I also specifically wanted a fixed, multi-output supply for standard project voltages such as 3.3V, 5V, 9V, 12V, ...
Despite having two high-quality variable (but analog) benchtop power supplies, I decided you can never have too many. I also specifically wanted a fixed, multi-output supply for standard project voltages such as 3.3V, 5V, 9V, 12V, ...
Borg Cube for Scouts STEM Camp
Introduction
What does one make for a Startrek-themed STEM camp for Scouts? Especially when given the Search and Rescue (SAR) activity base to run. Why this base you ask? Usually I run a radio d...Introduction
What does one make for a Startrek-themed STEM camp for Scouts? Especially when given the Search and Rescue (SAR) activity base to run. Why this base you ask? Usually I run a radio d...
ESP32 IR-Triggered Camera with Home Assistant Integration
I love the ESP line-up. I started by messing around with the ESP8266 and I completely fell in love with it. The 8266 is all I ever wanted from a microcontroller: WIFI connectivity, a decent amount of GPIO, a deep-sleep mode for batter...
IoT Mailbox
Getting letters and parcels is awesome, what’s not so awesome though is when you miss the postman and you don’t know if that important bit of mail arrived or not. Such a frustrating, yet mundane problem can be solved by creating...
Wifi Sniffer
This project started because I wanted to know the signal strength of the Wifi in various places around my house. I had set up a Pi Zero as a simple watering system controller. It would switch a solenoid on and off based on a 7 day schedule;...
3D-Printed GPS Speedometer
Introduction
I wanted a GPS speedometer that is portable, robust, and looks okay. I had been messing around with 3D printing and exploring GPS modules for a few years and wanted...
Math Scroller
I was looking for something educational to 3D-Print for my child in Thingiverse and came across the concept of the Math Spinner. I found the models lacked a method of checking the answer so I wanted to automate it. The core design is inspir...
Duck Off! A Duck Repellent Device
Introduction
We live on a rural property and have around 20 to 40 wild ducks around at any one time. We have a large dam and jetty, however it is almost unusable due to all the ...
Smart Watering System
Introduction This began as an idea after building a very basic single-channel unit. Commercial smart watering systems use a Wifi connection to the internet and get weather reports to determine the level of watering required. These systems...
YouTube Desktop Notifier
Do you get nightmares of losing your YouTube Subscribers? If you do, you are not the only one. Luckily I have made this "YouTube Desktop Notifier" to keep me up-to-date with my channels Subscriber and View Counts. This very simple DIY ...
Raspberry Pi Video Looper Display Installation | Overshare Video Festival
Introduction
A suspended ceiling display of forty repurposed screens and displays, each screening crowd-sourced content captured on mobile devices, installed in the entry to Testing Grounds...
Smart Home Makeover with HomeAssistant
IntroductionI wanted to bring ageing, and failing, Home Automation infrastructure into the modern age whilst retaining hardware investments already made. Our house had Universal Power Bus (UPB) dimmers and switches installed at build time...
Accurate IoT Clock With ESP8266
Being punctual is important. Hence accurate time is required. Clocks tend to miss out when it comes to accuracy especially when they are set by the user. So, why not get accurate time from the internet and use tried and tested hardware to ...
LoRaWAN Tank Level Sensor Node
My brother-in-law has a dairy farm in Victoria and many hours per week are wasted traversing the farm to check water tank levels, opening/closing valves, and other small tasks that could easily be remotely monitored and controlled. It was ...
House Power and Solar Monitor
I’ve had a Current Cost Power Monitor for a number of years which worked well until we put solar on the roof. The Current Cost can’t determine which direction the power is flowing and so power generation and con...
I’ve had a Current Cost Power Monitor for a number of years which worked well until we put solar on the roof. The Current Cost can’t determine which direction the power is flowing and so power generation and con...
The Great Doorbell Hack
Do you want a quick, easy, cheap RF remote control for your Raspberry Pi projects? Well, look no further than the front door! As you've probably got a half-duplex RF setup you've never considered using in a project before. Try this simple h...
Handheld UV Meter
UV is important to reptiles (and people) in processing vitamin D3 which is needed to absorb calcium. Without it reptiles often suffer from Metabolic Bone Disease (MBD) which leads to weak bones and can be fatal. Thankfully, pet shops have t...
8-Bit Breadboard Computer
This project is about how to build an 8 bit computer on breadboards, from 7400 series basic TTL. I am currently in the process of building mine, and will give an overview of what's involved. It is a great project that can teach you a lot ab...
Spirit In A Box Halloween Trick
Introduction
This project was born from the desire to craft a captivating and spine-tingling magic trick that would add an air of mystique to a Halloween and supernatural-themed party that ...
IR Break-Beam Stopwatch
This project is a simple stopwatch with a little bit of a twist! It operates like a conventional stopwatch… you can start and stop it, you can record lap times and you can review the lap times once you hit stop. The twist is th...
Desktop Infinity Mirror (Lasercut!)
A smaller version of our amazing Infinity-Mirror Table - the Desktop Infinity Mirror compresses all the colourful goodness into a picture frame-sized display. The entire design is made from laser-cut acrylic that we cut in-house. Check out ...
Fruit and Veggie Gaming Controller
In preparation for some Maker Faire's we were heading to last year, I wanted to combine the awesomeness of the Makey Makey platform, with the fun that is RetroPie. For those who don't know the Makey Makey, it's a fantastic platform that all...
Nintendo Wii Portable | Project G-Wii
Do you love your Wii and its ability to play all GameCube games perfectly but wish you could take it on the go like a Gameboy?
Well, I definitely did and if you're like me so do you. And here is the right place...
Do you love your Wii and its ability to play all GameCube games perfectly but wish you could take it on the go like a Gameboy?
Well, I definitely did and if you're like me so do you. And here is the right place...
Basic Weather Station
The aim of this project was to provide a cost effective and basic weather station for my backyard that can upload readings to Weather Underground. Part 2 of the project will be using this local data to trigger activities in and around my ho...
Datalogging Weather Station (Battery Powered)
This project will measure atmospheric conditions (Temperature, Humidity, Air Pressure) and log them to an SD card over a long period (months!) while running off a few AA or AAA cells. Usually, projects powered by an Arduino Uno are quite p...
ThingSpeak temperature & pressure logger
This project logs temperature and pressure observations to a ThingSpeak channel using an ESP8266 WiFi module.
For this project, I designed my circuit and ordered a PCB using easyEDA. The project gets power from a USB port and uses a...
For this project, I designed my circuit and ordered a PCB using easyEDA. The project gets power from a USB port and uses a...
littleBits Death Eater Skull!
Remote Controls are magical enough to recreate this awesome Death Eater Skull. You can switch it on from across the room and make it glow an evil green! Jake and Nathan built this invention at a littleBits Workshop down at the Core Electron...
Rad10
I wanted a self-contained internet radio with the following criteria: Reasonably compact/portable. Only required an external connection for power (i.e. wireless internet access). Simple controls for volume and mute-toggle.
Th...
Th...
12V Portable Battery Box
This project creates a functional 12-volt portable battery case for camping or other outdoor activities.The battery box provides a 12V cigarette lighter socket for running lights with an on/off switch for ease of use. There is also an Ander...
Simple Relay Timer
Introduction This project started because I needed to replace a water tap timer that had seen better days. The aim was to use a Raspberry Pi Pico and a couple of PiicoDev boards to do what the water timer did. The actual stopping a...
Vehicle GPS Logger and Speedometer
Purpose
To display time and speed to a driver while logging timestamped raw latitude, longitude and speed as returned by the GPS satellite network. This allows a driver to double-check th...
Accelerometer Controlled Animatronic Finger
This project incorporates two Arduino boards, in a Master/Slave setup. The master is one with an accelerometer (ADLX345) and the slave has a Servo attached (SG90). When tilting the accelerometer, the master Arduino tells the Slave Arduino t...
A Back to the Future Clock
This project started life as an alarm clock for my son made to look like the time circuit from the Back to the Future movies. The display can show the time in various formats, including the one from the movies of course. It's configurable v...
Particle Photon Weather Sensor
Recently I finished my first Particle Photon project. It’s basically a temperature, humidity, and barometric pressure monitor all in one! I’m not a programmer, but I know enough to tweak code when necessary. I have, on...
Cosplay Blaster
Hey guys! First time poster. I've been working on a blaster for my girlfriend's costume, and I thought I would share it with everyone. When triggered, it plays a selected sound effect and flashes the light. Pretty simple :)So, this is my fi...
AWS Lambda with Temperature data and the ESP32
In this project, I'm using an esp32 board combined with a thermistor, plus an Amazon Web Services Lambda API plus some web charting code for temperature sensing. Source code can be found in the GitHub repository: https://github.com/Acr...
Hot-Wire Bender for Acrylic
A simple, and affordable build that produces sharp, and consistent heat-bends. A nichrome wire heats a channel. Place the acrylic over the channel, wait for it to reach temperature, and pull the hingeing section to create a bend.
&l...
&l...
Water Tank Level Sensor
Update: Community member Chris has had a go at remaking this project after the original project contributor Denver made the original code repository private. GitHub links below will not work but the original project has been kept here for...
Wefted Waveforms
This project aims to fuse neopixel strips with papier mache and origami into a free-standing electro-sculpture. The freestanding structure is formed from wire mesh and papier mache. It is then painted and wired up with strips of LEDs conne...
Time lapsing in OctoPrint (Properly!)
Now that we have decked out our Lulzbot Taz 6 3D Printer with a really nice looking acrylic enclosure, I'm just about ready to turn on some serious 3D printing work. But before I dive into that endless pool of fun, it's a good time to take ...
Garage Door Sensor
This project uses a US100 ultrasonic distance sensor to detect instances of a garage tilt door being left open and sends an alert via the IFTTT mobile app. Additionally, the device logs temperature and pressure to a Thingspeak channel using...
p0wer - Control mains outlets over wifi.
As part of a larger home automation project, I wanted the ability to control some mains power outlets remotely. To achieve this, I interfaced the transmitter from an inexpensive 433MHz mains remote control kit with a raspberry pi zero w (vi...
Mailbox Delivery Notification System
Introduction
During the Covid lockdown, I needed something to do. The Postman or woman does not deliver mail every day as most bills come online. So I built this to notify me when the Pos...
IoT Plant Monitor
So, my wife wanted to have some small plants in the house. I didn’t, so we compromised, and got some plants. The only thing is that neither of us remembers to water them, so I wanted to build a sensor array to monitor the moisture con...
HUGE LED Pixel Panel
I’ve always been fascinated by LED screens and seeing beautiful colours mix and merge to create vibrant displays. I also love games, so what better way to combine the two than a giant LED pixel matrix which can play games, display aud...
Mini NES Style Game Console with Raspberry Pi
My son really wanted one of the mini NES when they were released, however he missed out. I already knew that you could use a raspberry pi as an arcade emulator, so I thought why not build him one.
I grew up playing old arcade machi...
I grew up playing old arcade machi...
The Hipster Coaster
We wanted to make a interactive display of the fun that can be had with DIY projects to take to Sydney Mini Maker Faire. We decided to do so by utilising the TinkerKit Braccio from Arduino.org, alongside some 3D Printing ingenuity, for an e...
Hogwarts Lights
Although there are commercially available lighting kits for Lego models, we found those that are available for this Hogwarts Castle can seem a little garish and don’t do the best job at concealing the wires. We felt that with t...
RPi Garbage Bin Reminder
Our local council picks up recycling bins one week and green waste the following week. Sometimes people forget which bins go out each week and perhaps they mistakenly put the wrong bins out. Not that that has ever happened to me of course! ...
LuMa 1 - The Neo Disco Ball
It is real and here it is! Including everything you need to make one a Luma 1 for yourself! So allow me to introduce you properly to the Luminator Mark 1. I'm talking all the ins and outs of this inside-out neo disco ball so you can ...
Makers love reviews as much as you do, please follow this link to review the products you have purchased.