This simple but effective enclosure will fit any 'classic Arduino' shaped development board - Adafruit have tested it for sure with the Arduino UNO R3, Adafruit Metro and...
Store your project safe and sound in this nice weatherproof box with a clear top. they picked up this box because Adafruit like the machinable ABS plastic body and tough...
Store your project safe and sound in this nice weatherproof box with a clear top. they picked up this box because Adafruit like the machinable ABS plastic body and tough...
Protect your electronic projects from rain and water splash using this waterproof IP68 enclosure. Made from high-quality ABS material, these boxes are sturdy and...
Here is a chic minimalist enclosure for your CLUE board! This case has been laser-cut specifically to accommodate the TFT display, tactile buttons, and capacitive pads.
These are our large, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it!
These are our small, beefy aluminum enclosures, which have been built tough enough to withstand a truck. This 2mm-thick, die-cast enclosure is rated IP54 against dust and splashing water. Because it’s aluminum, it’s easy to cut and drill so that you can add LCD screens, buttons and cable connections. If you want to “pretty up” your project, hit this with some fine-grit sand paper and buff it or just spray paint it!
These beefy, bright red plastic enclosures will give your widget the protection (and attention) it deserves. You’ve probably seen these used to enclose radio equipment or antenna baluns as they can be secured to a pole using U-bolts (not included). At about 3mm thick, this 74x158x90mm enclosure has plenty of space for gizmos, gadgets, widgets and doohickeys. The mounting flanges extend 19mm from either edge with two 50mm-spaced 7mm diameter holes.
These enclosures allow you to mount your micro gearmotor to other Actobotics products easily. Once your gearmotor is inserted, you can take advantage of the 0.77” hole pattern. These enclosures have a length of 1.14”, a width of 1”, and a thickness of 0.50”.
By popular demand, Adafruit now have a handy extension cord for all of Adafruit's JST-terminated battery packs (such as Adafruit's LiIon/LiPoly and 3xAAA holders). One end has a JST-PH...
This Romi Chassis accessory offers a convenient way to expand your Romi robot vertically by adding new tiers. The expansion plate has the same diameter as...
Stretch out your servo connections with this flexible servo extension cord. It has a 3 pin shrouded "male" connection to plug your servo into and then, 30cm later...
This panel mount USB-C extension cable enables you to more easily enclose a project that contains a USB-C port. The cable is 6" in length and includes two 14mm M3...
This 6-inch (150-mm), flat cable has 22-AWG wires and female “JR”-style connectors on both ends, the same kind of connector commonly found on RC hobby servos. It can be used to make connections between devices with 0.1" 3-pin male headers, such as between RC servo controllers or RC receivers and motor controllers with an RC interface. It can also be a convenient way to connect various 3-pin sensors to a robot controller.
This 12-inch (300-mm), flat cable has 22-AWG wires and female “JR”-style connectors on both ends, the same kind of connector commonly found on RC hobby servos. It can be used to make connections between devices with 0.1" 3-pin male headers, such as between RC servo controllers or RC receivers and motor controllers with an RC interface. It can also be a convenient way to connect various 3-pin sensors to a robot controller. The cable’s conductors each consist of 60 strands, making it more flexible than standard servo cables.
Heads up! Our forum has separate search to our main website. You are about to be redirected to our forum and when you arrive you can search for forum only content using the icon shown below. Click continue to search our forum.
Please continue if you would like to leave feedback for any of these topics:
Website features/issues
Content errors/improvements
Missing products/categories
Product assignments to categories
Search results relevance
For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.
Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.
Makers love reviews as much as you do, please follow this link to review the products you have purchased.