The AltIMU-10 v6 is an inertial measurement unit (IMU) and altimeter that features the same LSM6DSO gyro and accelerometer and LIS3MDL magnetometer as the...
The Pololu AltIMU-10 v5 is an inertial measurement unit (IMU) and altimeter that features the same LSM6DS33 gyro and accelerometer and LIS3MDL magnetometer as the MinIMU-9 v5, and adds an LPS25H digital barometer. An I²C interface accesses ten independent pressure, rotation, acceleration, and magnetic measurements that can be used to calculate the sensor’s altitude and absolute orientation
The MinIMU-9 v6 is an inertial measurement unit (IMU) that packs an LSM6DSO 3-axis gyro and 3-axis accelerometer and an LIS3MDL 3-axis magnetometer onto a...
The LSM6DSO combines a digital 3-axis accelerometer and 3-axis gyroscope into a single package. The sensor provides six independent acceleration and...
The LSM6DS33 combines a digital 3-axis accelerometer and 3-axis gyroscope into a single package. The sensor provides six independent acceleration and...
This carrier for ST’s LPS331AP digital barometer measures pressures from 260 mbar to 1260 mbar (26 kPa to 126 kPa) with absolute pressure accuracy over temperature down to ±2 mbar (0.2 kPa) and typical RMS noise of 0.02 mbar (0.002 kPa) in high-resolution mode. These pressures can easily be converted to altitudes. The board has a 3.3 V linear regulator and integrated level shifters that allow it to work over an input voltage range of 2.5 V to 5.5 V, and the 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards. The sensor offers I²C and SPI interfaces.
This sensor is a carrier/breakout board for the ST L3GD20H three-axis gyroscope, which measures the angular rates of rotation about the roll (X), pitch (Y), and yaw (Z) axes. Angular velocity measurements with a configurable range of ±245°/s, ±500°/s, or ±2000°/s can be read through a digital I²C or SPI interface. The board has a 3.3 V linear regulator and integrated level-shifters that allow it to work over an input voltage range of 2.5 V to 5.5 V, and the 0.1″ pin spacing makes it easy to use with standard solderless breadboards and 0.1″ perfboards.
Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, and BMP280... now Adafruit have got the next generation, the Adafruit BMP388 Precision Barometric...
The CMPS11 is our 3rd generation tilt compensated magnetic compass. It packs a 3-axis magnetometer, a 3-axis gyro and a 3-axis accelerometer. A Kalman filter combines the gyro and accelerometer to remove the errors caused by tilting of the PCB. The CMPS11 presents a result of 0-3599 representing 0-359.9 or 0 to 255.
Use this Bit to control your circuits with movement. The accelerometer senses how quickly you speed it up or slow it down. Snap it to a bargraph on a mounting board. Then give it a wave to visualize your movements.
Bosch has been a leader in barometric pressure sensors, from the BMP085. BMP180, BMP280, BMP388... now Adafruit have got the next generation, the Adafruit BMP390 Precision Barometric Pressure and Altimeter Breakout. As you would expect, this sensor is similar to its earlier versions but even better. The BMP390 has better precision than ever, which makes it excellent for environmental sensing or as a precision altimeter. It can even be used in either I2C and SPI configurations.
This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 MEMS accelerometer from Analog Devices, the LilyPad Accelerometer can detect joint movement as well as inclination and vibration.
This module integrates high-precision gyroscopes, accelerometer, microprocessor of high-performance and advanced dynamics solves and Kalman filter algorithms that...
Breakout board for the Analog Device ADXL345. The ADXL345 is a small, thin, low power, 3-axis accelerometer with high resolution (13-bit) measurement at up to ±16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.
The LIS3DH is a very popular low power triple-axis accelerometer. It's low-cost, but has just about every 'extra' you'd want in an accelerometer: Three axis sensing...
If your project is need of an accelerometer, take a look at this module. On-board is an ADXL345 triple axes accelerometer with high resolution (13-bit) up to ±16 g. The digital output data is formatted as 16-bit twos complement and accessible through either a SPI or I2C.
If you need a low-power, low-cost accelerometer with analogue output, take a look at this module. powered by the triple-axis ADXL335 accelerometer with a measurement range of up to ±3.6 g.
This Triple Axis Accelerometer with Bosch BMA220 is an ultra small triaxial, low-g acceleration sensor breakboard with SPI and I2C interface, aiming for lowpower consumer market applications. It allows measurement of accelerations in 3 perpendicular axes and thus senses tilt, motion, shock and vibration in cell phones, handhelds, computer peripherals, man-machine interfaces, virtual reality features and game controllers.
A reference design for the RP2040 Stamp, also a full-fledged RP2040 Uno form-factor development board! The Carrier is a reference design for the RP2040...
Heads up! Our forum has separate search to our main website. You are about to be redirected to our forum and when you arrive you can search for forum only content using the icon shown below. Click continue to search our forum.
Please continue if you would like to leave feedback for any of these topics:
Website features/issues
Content errors/improvements
Missing products/categories
Product assignments to categories
Search results relevance
For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.
Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.
Makers love reviews as much as you do, please follow this link to review the products you have purchased.