The cloudBit is the easiest way to create internet-connected devices. You can now snap the internet to anything! Retrofit your thermostat to control it remotely, or set up a sound-triggered alarm system that texts you alerts--the possibilities are endless. No programming, soldering or wiring required.
- Build anything, including a DIY Nest, SMS doorbell, and hundreds more ideas online!
- Connect everything! Your entire littleBits library can talk to the internet and vice versa
- Automate with IFTTT to connect with any web service, like Facebook, Gmail and Twitter, or hardware like NEST and Phillips HUE
- Remote control and readout to control your circuits across the room or across the world
- Code with the cloud API or the littleBits Arduino module for further customization [optional]
- Includes usb power module, wall adapter and cable for robust installations
Check out littleBits Tips and Tricks for more ideas on using the cloudBit.
New to littleBits? Check out the cloudBit Starter Kit!
The cloudBit is a single board computer running Linux. We use an USB WiFi adapter for networking, and once commissioned we automatically connect to the littleBits cloud. Once connected the cloudBit sends the littleBits cloud samples of the voltage on the input bitSnap™ with 10-bit precision, and the littleBits cloud is able to instruct the cloudBit to set the voltage on it's output bitSnap.
The RGB status LED lets you know what the cloudBit is doing. When it is purple the cloudBit is booting up, when it is yellow it is trying to connect to the WiFi access point, and when it has successfully connected to the littleBits cloud it turns green.
In order to tell the cloudBit what WiFi router to connect to you place it into "commissioning mode" by pressing and holding the setup button until the status LED turns blue.
When the cloudBit operates in commissioning mode it acts as an 802.11 access point and web server. When instructed by the user's browser the cloudBit scans for access points and returns the results to the browser for selection. Once the user sets up an access point the cloudBit enters normal mode.
When it operates in normal mode it attempts to connect to the configured access point and then communicates with the littleBits cloud over a TLS socket. If the cloudBit does become disconnected the status LED will turn red briefly, and then yellow as the cloudBit tries to automatically reconnect.
Once connected the litteBits cloud can instruct the cloudBit to output any voltage between 0V and 5V or any interval of time between 0 and 32 seconds.
Under The Hood
For the cloudBit we built an embedded Linux system based around a Freescale i.MX23 ARM926EJ-S processor. It has 64MB of RAM and boots a heavily modified version of the ArchLinux distribution from a 4GB SD card. The cloudBit uses an 802.11b/g/n USB adapter for networking, the Freescale's on-chip ADC and DAC for the input and output pins, and the GPIO pins for the setup button and the status LED. We've left pads on the bottom of the board so that you can connect to the cloudBit's serial console using 3.3V UART (8-N-1, 115,200 baud) and poke around.
The cloudbit currently supports networks with the following security standards: Open (no encryption), WEP, WPA and WPA2.
This product is listed in:
Documentation and Resources:
- The Maker Revolution
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - the transition from a consumer buying goods to eventually having a major part in their creation. The Maker Revolution places strong emphasis on free (...
- What is the better tech, innoBits or littleBits?
We get a lot of interest from parents and educators surrounding littleBits and innobits. Especially the difference between the two products. Both are magnetically connected electronic building blocks. Both products empower people to invent and create...
- The One Wand to rule them all!
Wands are cool, right? That's what Trinity, Adele, and April were thinking of our recent littleBits Workshop, down at the Core Electronics Knowledge Factory. Their inspiration for this project came straight from the films, in particular, the magic wands that Harry and co use throughout the Saga. They went a bit above a typical wand though, using a pressure sensor alongside a fan, buzzer, and bar graph to make their wand light up...
- littleBits Death Eater Skull!
Remote Controls are magical enough to recreate this awesome Death Eater Skull. You can switch it on from across the room and make it glow an evil green! Jake and Nathan built this invention at a littleBits Workshop down at the Core Electronics Knowledge Factory. At first, they tweaked an RGB LED Bit to be the perfect green and after some additions and problem solving they ended up with this remotely controlled Skull lamp. Just a...
Exact shipping can be calculated on the view cart page (no login required).
We deliver Australia-wide with these options:
- $3 for Small Items (3-7 days, not tracked, only available on selected small items)
- $6.95 for Standard Post (2-4 days, tracked)
- $9.95 for Express Post (Overnight for most of Australia, 2+ days for rural, tracked)
- Pickup - Free! Only available to customers who live in the Newcastle region (only after we email you to notify your order is ready)
International Orders - the following rates are for New Zealand and will vary for other countries:
- $11.49 for Pack and Track (3+ days, tracked)
- $16.50 for Express International (2-5 days, tracked)
If you order lots of gear, the postage amount might increment based on the weight of your order.
Our physical address (here's a PDF which includes other key business details):
Unit 18, 132 Garden Grove Parade
Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.