Raspberry Pi Compute Module 3+ 8 GB

SKU: CE06085 Brand: Raspberry Pi Guides (1)

Retired Product

Replaced by: Compute Module
This product has been replaced by: Compute Module
This product is no longer available. This page is only for reference.

The Compute Module is a Raspberry Pi in a more flexible form factor, intended for industrial application. CM3+ (Compute Module 3+) is the Raspberry Pi 3 B+-based revision of the original Compute Module. The big update to the CM3+ compared to the CM3 series is more eMMC Flash memory and the new heat spreader on the main processor which will let it run at full speed much faster without overheating.

The Compute Module contains the guts of a Raspberry Pi 3 B+ (the BCM2837B0 processor and 1GB RAM) as well as a 8GB eMMC Flash device (which is the equivalent of the SD card in the Pi). The Pi 3 B+ has a processor speed of 1.2GHz and runs at roughly 10 times the speed of the Pi 1 due to its quad-core CPU. This is all integrated on to a small 67.6mm x 31.1mm board which fits into a standard DDR2 SODIMM connector (the same type of connector as used for laptop memory).

The Flash memory is connected directly to the processor on the board, but the remaining processor interfaces are available to the user via the connector pins. You get the full flexibility of the BCM2837B0 SoC (which means that many more GPIOs and interfaces are available as compared to the Raspberry Pi), and designing the Module into a custom system should be relatively straightforward as the Pi Foundation has put all the tricky bits onto the Module itself.

A lite version of CM3+ is also available any eMMC Flash. The CM3+Lite brings the SD card interface to the Module pins so a user can wire this up to an SD card of their choice.

Technical Details

  • Processor: Broadcom BCM2837B0, Cortex-A53 64-bit Soc @ 1.2GHz
  • Memory: All boards come with 1GB LPDDR2 SDRAM as standard
  • On board flash memory is supplied as follows: CM3+/8GB (8GB eMMC Memory)
  • Multimedia: H.264, MPEG - 4 decode (1080p30), H.264 encode (1080p30), OpenGL ES 1.1, 2.0 graphics
  • Operating temperature: -20 to +70º C
  • Operating System: NOOBS 3.0.0 (released 16 November 2018) or later
  • Product Dimensions: 67.6mm x 31.1mm x 3.7mm / 2.7" x 1.2" x 0.1"
  • Product Weight: 9.0g / 0.3oz

This product is listed in:

Retired

Product Comments

Exact shipping can be calculated on the view cart page (no login required).

Products that weigh more than 0.5 KG may cost more than what's shown (for example, test equipment, machines, >500mL liquids, etc).

We deliver Australia-wide with these options (depends on the final destination - you can get a quote on the view cart page):

  • $3+ for Stamped Mail (typically 10+ business days, not tracked, only available on selected small items)
  • $7+ for Standard Post (typically 6+ business days, tracked)
  • $11+ for Express Post (typically 2+ business days, tracked)
  • Pickup - Free! Only available to customers who live in the Newcastle region (must order online and only pickup after we email to notify you the order is ready). Orders placed after 2PM may not be ready until the following business day.

Non-metro addresses in WA, NT, SA & TAS can take 2+ days in addition to the above information.

Some batteries (such as LiPo) can't be shipped by Air. During checkout, Express Post and International Methods will not be an option if you have that type of battery in your shopping cart.

International Orders - the following rates are for New Zealand and will vary for other countries:

  • $12+ for Pack and Track (3+ days, tracked)
  • $16+ for Express International (2-5 days, tracked)

If you order lots of gear, the postage amount will increase based on the weight of your order.

Our physical address (here's a PDF which includes other key business details):

40 Aruma Place
Cardiff
NSW, 2285
Australia

Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.

Have a product question? We're here to help!

Write Your Own Review

Guides

The Maker Revolution

The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...
The Maker Revolution celebrates the creation of new devices and the modification of existing ones - ...

Raspberry Pi Boards Compared

The Raspberry Pi has revolutionized the world of single-board computers, offering a platform for lea...
The Raspberry Pi has revolutionized the world of single-board computers, offering a platform for lea...

Projects

The Snooze Logger - A Wearable Sleep Position Monitor

Everyone needs a good night’s sleep!One of the factors affecting sleep quality is sleep posit...
Everyone needs a good night’s sleep!One of the factors affecting sleep quality is sleep posit...

Spectral Animations with a DIY MSGEQ7 I2C Device

Frequency Reactive LEDs, i2c Protocol, Raspberry Pi, and Other Adventures.Here at Pix Incorpor...
Frequency Reactive LEDs, i2c Protocol, Raspberry Pi, and Other Adventures.Here at Pix Incorpor...

VisionSphere: Camera Motion Detection for Raspberry Pi

A simple camera motion detection system for Raspberry Pi. Definitely written with Aussie's in mind ...
A simple camera motion detection system for Raspberry Pi. Definitely written with Aussie's in mind ...
Feedback

Please continue if you would like to leave feedback for any of these topics:

  • Website features/issues
  • Content errors/improvements
  • Missing products/categories
  • Product assignments to categories
  • Search results relevance

For all other inquiries (orders status, stock levels, etc), please contact our support team for quick assistance.

Note: click continue and a draft email will be opened to edit. If you don't have an email client on your device, then send a message via the chat icon on the bottom left of our website.

Makers love reviews as much as you do, please follow this link to review the products you have purchased.