Search results for: 'actuator mounting brackets'

This machined aluminum bracket allows the Concentric LD series linear actuators to be mounted to a structure. Complete mounting hardware is included. Two brackets are required for mounting each actuator.

This bracket was designed specifically for the Glideforce Light-Duty (LD) linear actuators. It is made from stamped, zinc-plated steel and has been tested...

This bracket was designed specifically for the Glideforce Medium-Duty (MD) linear actuators. It is machined out of a single piece of aluminum and has been...

This bracket was designed specifically for the Glideforce Industrial-Duty (ID) linear actuators. It is made from stamped, black powder coated steel and...

This bracket was designed specifically for the Glideforce Medium-Duty (MD) linear actuators. It is made from stamped, zinc-plated steel and has been...

This DC gearmotor has an integrated M3*25mm long rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 98RPM...

This bracket was designed specifically for the Glideforce Industrial-Duty (ID) linear actuators. It is machined out of a single piece of aluminum and has...

This 12 V high-speed light-duty (LD) linear actuator with a 5:1 gear reduction can lift loads up to 12 kgf [27 lbs or 120 N] and can withstand static...

This NEMA 17-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1.2 A at 4 V, allowing for a holding torque of 3.2 kg-cm (44 oz-in).

This gearmotor is a miniature high-power, 12 V brushed DC motor with long-life carbon brushes and a 986.41:1 metal gearbox. It has a cross section of...

This 12 V industrial-duty (ID) linear actuator uses an efficient ball screw drive to lift loads up to 450 kgf [1000 lbs or 4500 N] and withstand static...

This NEMA 17-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1.7 A at 2.8 V, allowing for a holding torque of 3.7 kg-cm (51 oz-in).

This NEMA 14-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 280 mA at 7.4 V, allowing for a holding torque of 650 g-cm (9 oz-in).

This DC gearmotor has an integrated M4*55mm threaded rod as its output shaft, turn it into a linear actuator. 6V rated voltage, the no-load speed could arrive 150RPM, equivalent to 1.75mm/s. The brass faceplate has two mounting holes threaded for M1.6 screws (1.6mm diameter, 0.35mm thread pitch), or you can use the mounting bracket or extended mounting bracket, which are specifically designed to securely mount the gear motor while enclosing the exposed gears.

This NEMA 23-size hybrid stepping motor can be used as a unipolar or bipolar stepper motor and has a 1.8° step angle (200 steps/revolution). Each phase draws 1 A at 7.4 V, allowing for a holding torque of 9 kg-cm (125 oz-in).

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft....

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft....

This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft....

This pancake bipolar stepping motor from Sanyo has a 1.8° step angle (200 steps/revolution). It offers a holding torque of 2.2 kg-cm (30 oz-in), and each phase draws 1 A at 5.9 V. This stepper motor’s flat profile (21 mm including the shaft) allows it to be used in places where more traditional stepper motors would be too bulky.