empowering creative people

  1. 2A Motor Shield For Arduino DRI0009 DFRobot Australia

    2A Motor Shield For Arduino

    SKU: DRI0009
    This DFRobot Arduino Compatible Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mount onto standard Arduino Duemilanoveand Arduino Mega. Learn More
    $24.79 AUD, inc GST
    AUD, inc GST
    delivered by
    Tue 6th of Dec

    $24.79 AUD

  2. 1A Motor Shield For Arduino DRI0001 DFRobot Australia

    1A Motor Shield For Arduino

    SKU: DRI0001
    This Motor shield for Arduino uses L293 chip which allow to drive two 7-12V DC motors with maximum 1A current. This shield can be directly mount onto standard Arduino Duemilanove and Arduino Mega. Learn More
    $17.11 AUD, inc GST
    AUD, inc GST
    delivered by
    Tue 6th of Dec

    $17.11 AUD

  3. Motor Driver 1A Dual TB6612FNG ROB-09457 Sparkfun Australia

    Motor Driver 1A Dual TB6612FNG

    SKU: ROB-09457
    The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Learn More
    $13.03 AUD, inc GST
    AUD, inc GST
    delivered by
    Tue 6th of Dec

    $13.03 AUD

  4. 2A Dual Motor Controller DRI0002 DFRobot Australia

    2A Dual Motor Controller

    SKU: DRI0002
    This is the DFRduino Mega 2560 V2.0. It is fully compatible with Arduino Mega 2560 R2. This board features the ATmega8U2 programmed as a USB-to-serial converter and it has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU. Learn More
    $27.27 AUD, inc GST
    AUD, inc GST
    delivered by
    Tue 6th of Dec

    $27.27 AUD

  5. DC Motor Driver 2×15A - Lite DRI0018 DFRobot Australia

    DC Motor Driver 2×15A - Lite

    SKU: DRI0018
    This DC Motor Driver can be used in 4WD mobile robot platforms,Combat robots, smart car competition, to drive pumps, electric fans, conveyors, etc... Learn More
    $74.13 AUD, inc GST
    AUD, inc GST
    delivered by
    Tue 6th of Dec

    $74.13 AUD

  6. Big Easy Driver ROB-12859 Sparkfun Australia

    Big Easy Driver

    SKU: ROB-12859
    The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. It’s the next version of the popular Easy Driver board. Learn More
    $30.38 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $30.38 AUD

  7. Monster Moto Shield DEV-10182 Sparkfun Australia

    Monster Moto Shield

    SKU: DEV-10182
    This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of high-current motors! The VIN and motor out are pitched for our 5mm screw terminals (not included), making it easy to connect larger gauge wires. Learn More
    $106.32 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $106.32 AUD

  8. EasyDriver - Stepper Motor Driver ROB-12779 Sparkfun Australia

    EasyDriver - Stepper Motor Driver

    SKU: ROB-12779
    The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). The EasyDriver requires a 6V to 30V supply to power the motor and can power any voltage of stepper motor. The EasyDriver has an on board voltage regulator for the digital interface that can be set to 5V or 3.3V. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. Learn More
    $20.38 AUD, inc GST
    AUD, inc GST
    delivered by
    Tue 6th of Dec

    $20.38 AUD

Set Ascending Direction

8 Item(s)