empowering creative people

  1. Logic Level Converter Bi-Directional BOB-12009 Sparkfun Australia

    Logic Level Converter Bi-Directional

    SKU: BOB-12009
    If you’ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level converter from our previous versions is that you can successfully set your high and low voltages and step up and down between them safely on the same channel. Each level converter has the capability of converting 4 pins on the high side to 4 pins on the low side with two inputs and two outputs provided for each side. Learn More
    $4.05 AUD, inc GST
    AUD, inc GST
    $4.05 AUD
  2. Breakout Board for USB microB BOB-12035 Sparkfun Australia

    Breakout Board for USB microB

    SKU: BOB-12035
    This simple board breaks out a micro-B USB connector’s VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popular micro-B USB to your project, but don’t want to put up with soldering the tiny connector, this is the board for you. Learn More
    $2.70 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $2.70 AUD

  3. MAX3232 Breakout BOB-11189 Sparkfun Australia

    MAX3232 Breakout

    SKU: BOB-11189
    The ‘must have’ IC for TTL/CMOS projects finally has its own breakout board! This is the RS232 converter IC that is capable of running at 3V and communicating with 5V logic. Learn More
    $7.40 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $7.40 AUD

  4. Breakout Board for RJ45 BOB-00716 Sparkfun Australia

    Breakout Board for RJ45

    SKU: BOB-00716
    RJ45 connectors are the kind that are used for Ethernet jacks, but they make great general purpose connectors when you need a lot of conductors. This is a small PCB that brings out the pins of the RJ45 connector to an in-line 0.1" footprint. Use with break-away headers for breadboarding or create your own RJ45 cable. Check the related items for Ethernet cable and connectors to go with it! Learn More
    $1.97 AUD, inc GST
    AUD, inc GST
    delivered by
    Mon 12th of Dec

    $1.97 AUD

  5. Breakout Board for microSD Card POLOLU-2597 Pololu Australia

    Breakout Board for microSD Card

    SKU: POLOLU-2597
    This simple board breaks out the pins of a microSD card connector to a 0.1″ pin spacing that is compatible with standard perfboards, solderless breadboards, and 0.1" connectors. Learn More
    $4.72 AUD, inc GST
    AUD, inc GST
    delivered by
    Wed 14th of Dec

    $4.72 AUD

  6. Adafruit ATWINC1500 WiFi Breakout ADA2999 Adafruit Australia

    Adafruit ATWINC1500 WiFi Breakout

    SKU: ADA2999
    Connect your Arduino to the Internet with this fine new FCC-certified WiFi module from Atmel. This 802.11bgn-capable WiFi module is the best new thing for networking your devices, with SSL support and rock solid performance - running Adafruit's adafruit.io MQTT demo for a full weekend straight with no hiccups (it would have run longer but Adafruit had to go to work, so they unplugged it). Adafruit like these so much, they've completely replaced the CC3000 module on all Adafruit's projects. Learn More
    $37.53 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $37.53 AUD

  7. RS-485 Breakout BOB-10124 Sparkfun Australia

    RS-485 Breakout

    SKU: BOB-10124
    This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply. Learn More
    $15.19 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $15.19 AUD

  8. Breakout Board for microSD Transflash BOB-00544 Sparkfun Australia

    Breakout Board for microSD Transflash

    SKU: BOB-00544
    Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested. Learn More
    $6.19 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $6.19 AUD

  9. SSOP to DIP Adapter 16-Pin BOB-00498 Sparkfun Australia

    SSOP to DIP Adapter 16-Pin

    SKU: BOB-00498
    8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any pin count up to 28 pins. Designed to be used with 0.65mm pitch devices but can also be used with 0.025" pitch devices (comes out to ~0.635mm). We’ve made these 0.635mm devices fit just fine. Can be used with packages from 0.200" (5mm) up to 0.450" (11.4mm) in width. Breaks out SSOP pins to standard .6" (600mil) and .3" (300mil) DIP width to be used in any DIP socket or bread board. The 8 and 16 boards have a 300mil spacing. The 20 and 28 pin boards have 600mil spacing between the DIP pins. Learn More
    $2.70 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $2.70 AUD

  10. SparkFun USB to Serial Breakout - FT232RL BOB-12731 Sparkfun Australia

    SparkFun USB to Serial Breakout - FT232RL

    SKU: BOB-12731
    This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip. Learn More
    $20.38 AUD, inc GST
    AUD, inc GST
    delivered by
    Fri 9th of Dec

    $20.38 AUD

Set Ascending Direction

1-10 of 43

Page:
  1. 1
  2. 2
  3. 3
  4. 4
  5. 5